Miele T 9800 Descriptive Technical Documentation page 83

DTD no. 12-9800
Service function
Buzzer LED
Software status
Fault memory To
1)
read and delete,
refer to
Component test
Sensor test
Operating hours,090
2.6 Operating hours
meter
Table 4: Service mode summary
1)
Show saved faults in ascending order: Press the Start/Stop pad.
2)
Delete fault memory: Press the Start/Stop pad for more than 4 seconds (deletes all saved faultst).
3)
Select and activate components: Press the Start/Stop pad, after 1 s the component is automatically activated.
Pressing Start/Stop again switches the current component off and starts the next one. If component testing is stopped
and later called up again, the program resumes with the last component that was activated. The component test
switches off automatically 30 minutes after the last component is activated.
4)
In 1 rib sensing, only one rib is used for the reading.
5)
Select sensor and start the test: Press the Start/Stop pad.
05.12.2006, US_am
short
-
F 1, F 1, Heater bank NTC short circuit, refer to F
1 Short circuit in NTC temperature sensor
F 2, Heater bank NTC open circuit, refer to F 2
Open circuit in NTC temperature sensor heating/
F 3, Drying air NTC short circuit, refer to F 3 NTC
temperature sensor drying air (1R30)
1
F 4 Drying air NTC open circuit, refer to F 4 NTC
2)
temperature sensor drying air (1R30)
F 50, Motor stalls and heater is on for 3 s, refer to
F 50 Motor stalls and heater is on for 3 seconds,
F 55, Safety time exceeded, refer to F 55
Overriding time limit exceeded, approx. 180 min,
F 66, Air leakage fault, refer to F 66 Air leakage,
Drive motor/Fan motor (M5) on in a rhythm of 10 s left / 2 s
Heater relay (1K1/1) / Heater (R1) on and Drive motor/Fan motor
(M5) on in a rhythm of 10 s left / 2 s pause / 10 s right / 2 s
Check the residual moisture sensor (B3/1) for low ohmic status
(continuity). Requirement: Electrical connection between drum
3)
2
Check the residual moisture sensor (B3/1) for high ohmic status
(isolation). Requirement: No electrical connection between drum
Heater relay (2K1/1) on and Drive motor/Fan motor (M5) on
Heater relays (1K1/1, 2K1/1, 3K1/1) on, Heater (R1, R2, R3) on
5)
3
Door lock (A2): Door closed => Switch closed = > buzzer on.=>
Program/Power module (EPWL) operating hours:
Long flashing signal for the number of 1000s,
short flashing signal for the number of 100s. (12
4
times long + 6 times short = 12000 h + 600 h =
Descriptive Technical Documentation
Option
Drying LED
Program index XY
F 0, No fault, all ok.
heating/drying (2R30), 090 3.8
drying (2R30) , 090 3.9
circuit, 090 3.10
circuit, 090 3.11
090 3.12
090 3.13
090 3.14
All components inactive
pause / 10 s right / 2 s pause.
pause.
4)
and sensor rib.
and sensor rib.
Steady buzzer tone
LED displays flash (0.5 Hz)
and Drive motor/Fan motor (M5) on
All sensors inactive
. Door open => Switch open = buzzer off.
12600 h.
This information should not be duplicated or passed on without Miele approval. All rights reserved.
090-21
long shor
X
-
-
-
-
Short
-
Open
5
5
6
x000 h y00 h
Y
-
1
2
3
4
-
5
6
-
1
2
4
5
6
7
8
9
-
1