Glossary; Xv. Glossary - GE NetworX NX-4V2 Installation And Startup

XV.

GLOSSARY

Abort
If enabled, the NX-4V2 will wait the programmed number of seconds in location 40 prior to sending an alarm. During this delay time, the
"Cancel" LED will flash. To abort the report, type in a code and press the Cancel key. The LED will extinguish. If the report is not
aborted within the allotted time, the LED will extinguish when the report is sent. ADialer Delay@ must be enabled in the ACharacteristic
Select@ of locations 110-169. (Loc 40 & 110-169, pg 19 & 23-27)
AC Fail / Low Battery Report / Warning
The NX-4V2 can be programmed to report AC failure and/or Low Battery conditions to the central station. It can also be programmed to
sound the keypad immediately upon detection of the condition. The AC failure report/warning can be delayed. (Loc 37 & 39, pg 17)
AC Power / Low Battery Sounder Alert
If enabled, the NX-4V2 will beep the keypad sounder upon arming or disarming if the AC power is missing or a low battery has been
detected. (Loc 23, pg 15)
Arm / Disarm Codes
The NX-4V2 can have 8 four-digit codes or six-digit codes to arm/disarm the control. All codes must have the same number of digits.
The factory default for User #1 is
to enter the new arm/disarm codes. (Loc 41, pg 19)
Automatic Arming
If programmed, the NX-4V2 will Auto Arm at a specified time. At this time, the keypad will beep for 50 seconds before the panel arms.
The arming process will be stopped if a code is entered on the keypad. The NX-4V2 will attempt to arm after every 45 minutes of
inactivity until the next "opening" time (loc. 52), or until the system is armed. The 45-minute timer will be extended when there is activity
in the building causing the "Ready" LED to turn off and on. If closing reports are sent, the user code will be 97. (Loc 23 & 52-55, pg 15
& 21)
Automatic Bypass / Instant Arming
When enabled, the control panel can automatically bypass interior follower zones if an exit is not detected during the exit delay time.
Entry delay zones can also be made instant. (Loc 23, segments 1 & 3, pg 15)
Auto Cancel / Abort
If enabled, the Cancel and/or Abort features will be automatic (pressing the [Cancel] button is not required). The Cancel and Abort
features, in locations 23 & 40 respectively, must be enabled to permit this Auto feature to work. For proper operation of these features,
ADialer Delay@ must be enabled in the ACharacteristic Select@ of locations 110-169 Zone Types. (Loc 41, pg 19)
Auto Test
This feature will cause the panel to call the central station to report a communicator test at a specified interval. (Loc 51, pg 20)
Auxiliary Outputs
The NX-4V2 has 2 programmable outputs that can be used to activate relays, LED=s, etc. (See the terminal description on pg 6 and Loc
45-50, pg 19)
Auxiliary Power Over-current
The NX-4V2 will illuminate the "Service" LED on the keypad whenever too much current is drawn from any device powered by the
system. This condition can be reported to the central station. (Loc 37, pg 17)
Box Tamper
The NX-4V2 has an input for a normally closed tamper switch (see terminal drawing). The Box Tamper can be programmed to report
and/or sound the siren and/or the keypad. These terminals can be enabled or disabled in programming. (Loc 37 & 39, pg 17)
Built In Siren Driver
The NX-4V2 has a built-in 112db-siren driver. When desired, this built-in driver can be easily converted to a 1-amp voltage output
through programming. (Loc 37, pg 17)
Bypass Toggle
This feature will enable the end user to toggle (turn on or off) the bypass of an interior zone with the system armed by pressing the
[Bypass] key. (Loc 23, pg 15)
Call Back
When enabled, the control will use the call back phone number to call the download computer before beginning a download. (Loc 21,
pg 15)
Cancel
If enabled, the NX-4V2 will send a "Cancel" report if when the system is disarmed and the [Cancel] button is pressed within 5 minutes of
an alarm. Once the [Cancel] key is pressed, the "Cancel" LED will illuminate until the central station acknowledges the "Cancel" report.
ADialer Delay@ must be enabled in the ACharacteristic Select@ of locations 110-149. (Loc 23, pg 15)
Code Required Options
The NX-4V2 can be programmed to require a code for bypassing zones and/or initiating a download using the
function. (Loc 23 & 41, pg 15 & 19)
Communication Formats
The NX-4V2 can report in multiple formats. It is recommended that you use Contact ID or SIA formats if possible. If you wish to report to
a pager or in a 4+2 format to a central station, you must program each code to be reported. (Loc 56-83 & 111-169, pg 22-23 & 23-27)
Cross Zoning
This feature requires two or more trips on a zone or zones programmed as "cross zones" within a specified time before reporting an
alarm. During the time between trips, the NX-4V2 can be programmed to sound the keypad and/or the siren. The NX-4V2 can also be
programmed to report an alarm after two or more trips on the same zone. (Loc 37, 39, 40 & 110-149, pg 17, 19, 23-27)
NX-4V2 Control
ÎÏÐÑ
when using a 4-digit code, or
WWW.DIYALARMFORUM.COM
ÎÏÐÑÒÓ
for a 6-digit code. This code can then be used
NOTE: This feature must be disabled for UL installations
r98 r99
or
35