Table of Contents
Advertisement
Quick Links
The Brewmaster
®
Belt-Driven Ceiling Fans
Long Neck FP20
Net Weight 15 lbs
(6.8 kg)
Motor Assembly
Net Weight 15 lbs
(6.8 kg)
Short Neck FP10
Net Weight 11 lbs
(5.0 kg)
Suitable for use with Solid State Speed Controls
WARNING: Support Directly From Building Structure
Model No. FP10 / 20 Fan Series
Model No. FP1280**-220 Motor Series
OWNER'S MANUAL
READ AND SAVE THESE INSTRUCTIONS
Advertisement
Table of Contents
Related Manuals for Fanimation FP10 / 20 Fan Series
Summary of Contents for Fanimation FP10 / 20 Fan Series
- Page 1 Short Neck FP10 Net Weight 11 lbs (5.0 kg) Suitable for use with Solid State Speed Controls WARNING: Support Directly From Building Structure Model No. FP10 / 20 Fan Series Model No. FP1280**-220 Motor Series OWNER’S MANUAL READ AND SAVE THESE INSTRUCTIONS...
-
Page 2: Table Of Contents
Fanimation. 7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty. 8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must ac- company authorized returns and must be sent freight prepaid to Fanimation. -
Page 3: (Motor Assembly) Unpacking Instructions And Parts Identifi Cation
• Pulley Head Assembly and hardware parts (Figure 2) Fanimation. Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. -
Page 4: (Pulley Assembly) Unpacking Instructions And Parts Identifi Cation
Unpacking Instructions and Parts Identifi cation (cont’d) FP10 (Short)/FP20 (Long) Pulley Assembly and Hardware Parts Identifi cation FP20 Long Neck Pulley Assembly FP10 Short Neck Pulley Assembly Blade Holder to Hub Screws 10-32 x ½˝ (5) Wood Blade Holders (for use with FP1022, FP1026, Traditional Blade Holders FP1030 blade sets) (for use with Palm, Bamboo,... -
Page 5: Electrical And Structural Requirements
Electrical and Structural Requirements Your new ceiling fan will require a grounded electrical supply line of 220-240 VAC, 50 Hz circuit. Plywood (¾˝ thick min.) Backing Secured to INSTALLATION NOTE Structural Member Outlet Box Flush It is recommended that each fan and the motor have to Finished ¾˝... -
Page 6: How To Hang And Wire Your Ceiling Fan
& Flat Fanimation. Substitution of parts or accessories not Washer designated for use with this product by Fanimation could (4 places) result in personal injury or property damage. Contact your retail store for missing or damaged parts. - Page 7 How to Hang and Wire Your Ceiling Fan (cont’d) If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. ▲WARNING To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.
- Page 8 How to Hang and Wire Your Ceiling Fan (cont’d) 11. After the connections have been made, tighten the lag Ceiling Joist bolts to secure fan base assembly to the ceiling, making Junction sure that the electrical wires are completely inside the base assembly and not pinched between the base and the ceiling.
-
Page 9: Belt Splicing Instructions
Belt Splicing Instructions 1. Wrap the belting around the two pulleys that will be connected and overlap the belting as shown. Use the spring clamps provided to hold the belting in place temporarily. With the clamps remaining in the same place, grasp both ends of the belting and pull tight. -
Page 10: Mounting The Fan Blades
Mounting the Fan Blades CAUTION Side B Do not connect fan blades until the fan is completely installed. Hanging fan with blades connected may result in damage to the fan blades. Natural Palm Leaf, Woven Bamboo, Woven Wicker Fan Blade Blades 1. -
Page 11: Operating Your C3-220 Wall Control
Operate Your C3-220 Wall Control 1. Restore electrical power and operate your fan by rotating the control knob to desired setting (Figure 1): • 3 Position – low fan speed • 2 Position – medium fan speed • 1 Position – high fan speed •... -
Page 12: Trouble Shooting
Trouble Shooting ▲WARNING For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble Probable Cause Suggested Remedy 1. FAN WILL NOT START 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. -
Page 13: Exploded-View Illustration & Parts List, Motor Assembly
The Brewmaster Motor FP1280**-220 ® Exploded-View Parts List Ref. # Description Part # Brewmaster Motor Assembly FMA1280 Switch Cap Assembly PSW50 Flat Washer Switch Cap Base Motor Pulley Motor Housing M/S, Washer Hd, -24 x 3½˝, Black Motor Assembly Hex Nut, -24 x 4mm (4) Lock Nut, Nylon Insert, -24 x 5mm (4) -
Page 14: Parts List, Pulley Assembly
Parts List Ref. # Description Part # Pulley Assembly FP10 /FP20 Pulley with set screw Short Frame (Short model) Long Frame (Long model) Cushion, Bearing, Black Bearing Shaft Blade Holder (2) (Wooden Blades only) P1212 Bag, BH to Hub Screws,10-32 x ½˝,Black (5) HDWFP10HB Bag, Lag Bolt, ¼˝... -
Page 15: Exploded-View Illustration, Pulley Assembly
The Brewmaster Pulley Assembly Pack ® FP10__ / FP20__ (Short) (Long) Exploded-View NOTE: The illustration shown is not to scale or its actual confi guration may vary. Figure 2... - Page 16 10983 Bennett Parkway Zionsville, IN 46077 Toll Free (888) 567-2055 FAX (866) 482-5215 Outside U.S. call (317) 733-4113 Visit Our Website www.fanimation.com Copyright 2008 Fanimation 2008/02...