Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Fanimation The Caruso FP7000 Series
Summary of Contents for Fanimation The Caruso FP7000 Series
-
Page 1: Ceiling Fan
The Caruso ® Ceiling Fan Net Weight (without blades): 60 lbs (27.22kgs) *Select Finish Model No. FP7000** OWNER’S MANUAL READ AND SAVE THESE INSTRUCTIONS *Damp Location Model; Top of fan is marked, “Suitable For Use In Damp Locations”... -
Page 2: Table Of Contents
Fanimation. 7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty. 8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must ac- company authorized returns and must be sent freight prepaid to Fanimation. -
Page 3: Tools Needed For Assembly
Fanimation. Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. -
Page 4: Electrical And Structural Requirements
Electrical and Structural Requirements Your new ceiling fan will require a grounded electrical supply line of 120VAC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 100 lbs. Figure 1 depicts different structural confi... - Page 5 Fan Alignment And Hanger Bracket Installation (cont’d) INSTALLATION NOTE Be sure that the safety cable (along with the electrical supply wires) is pulled through the downrod when installing the downrod to the support bar. 4. Position the bottom end of the downrod inside the housing support located at the center of the support bar assembly.
-
Page 6: Assembling And Hanging The Ceiling Fan
Assembling and Hanging the Ceiling Fan CAUTION The fan must be hung with at least 7´ of clearance from floor to blades (vertical position as shown in Figure 1) INSTALLATION NOTE Do not connect fan blades until the fan is completely installed. - Page 7 Assembling and Hanging the Ceiling Fan (cont’d) 4. You have now completed the assembly of the downrod/ support bar/motors assembly. You can now proceed with with step 5 below. ▲WARNING Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard.
-
Page 8: Wiring And Control Options
2. Optional fan & light slide wall control (C6). Please see instructions provided with control. NOTE: If you are using a Fanimation Light Fixture with your fan, see Ceiling Fan Light Kit Installation Instructions (packed with light kit) for wiring. -
Page 9: How To Wire Your Ceiling Fan - C3-Ca Wall Control
How to Wire Your Ceiling Fan - C3-CA Wall Control If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. NOTE: If fan or supply wires are different colors than indicated, have this unit installed by a qualifi... -
Page 10: Installing The Canopy Housing
Installing the Canopy Housing NOTE: This step is applicable after the necessary wiring is completed. (see pages 8 and 9) ▲WARNING To avoid possible fire or shock, make sure that the electrical wires are completely inside the canopy housing and not pinched between the housing and the ceiling. 1. -
Page 11: Blade Attachment
INSTALLATION NOTE Attach the fan blades after hanging the fan body and wiring the fan to prevent blade breakage or damage. 1. Blade holders come packed in two different bundles, one blade holder set is marked with a red dot (5 pcs) and one blade holder set is marked with white dot (5 pcs). -
Page 12: Adjusting And Setting The Motor Head Angles
Adjusting and Setting the Motor Head Angles INSTALLATION NOTE BOTH MOTOR HEADS MUST BE SET AT THE SAME ANGLE! NOTE: This step is applicable after the necessary fan assembling, hanging and wiring is completed. CAUTION To reduce the risk of personal injury or damage to fan assembly, be sure to support the motor heads when adjusting or changing angles on the “knee-joint”. -
Page 13: Downrod / Blade Lengths Vs Motor Head Angle Specifi Cations
Downrod / Blade Lengths vs Motor Head Angle Specifi cations Vertical 15° 30° 45° 60° CARUSO 18˝ Blades “A” Motor Tilt Dim. Angle w/24˝ DR Vertical 54½˝ 15˚ 55˝ 30˚ 54½˝ 45˚ 52½˝ 60˚ 49˝ *22˝ Natural Palm Blades Are NOT To Be Used At The 60° Setting CARUSO ®... -
Page 14: Controlling Airfl Ow Patterns
NOTE: Choose one of the following color code blade & switch set-up combinations for the desired airflow direction as shown. INSTALLATION NOTE This section is applicable after the fan and the blades are completely installed. 1. Note the locations of the color code on the blade arm and the reversing switch. -
Page 15: Trouble Shooting
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connections in the switch housing. 1. -
Page 16: Parts List
Before discarding packaging materials, be certain all parts have been removed Contact your retail store for repair parts. When ordering repair parts, always give the following information. Parts List Model #FP7000** Description ˝ Cap Head Screw (1) How To Order Parts • Part Number •... -
Page 17: Exploded-View Illustration
The Caruso FP7000** ® Exploded-View NOTE: The illustration shown is not to scale or its actual confi guration may vary, wires omitted for clarity. - Page 18 10983 Bennett Parkway Zionsville, IN 46077 Toll Free (888) 567-2055 FAX (866) 482-5215 Outside U.S. (317) 733-4113 Visit Our Website www.fanimation.com Copyright 2008 Fanimation 2008/06...
Need help?
Do you have a question about the The Caruso FP7000 Series and is the answer not in the manual?
Questions and answers