Table of Contents
Advertisement
SW58 No. 1 ~ No. 8 Reserved
Set to "0".
SW59 No. 1 ~ No. 8 Reserved
Set to "0".
SW59 No. 8 Reserved
Set to "1".
SW60 No. 1 ~ No. 3 Reserved
Set to "0".
SW60 No. 4 Reserved
Set to "1".
SW60 No. 5 Reserved
Set to "0".
SW60 No. 6 Reserved
Set to "1".
SW60 No. 7 Reserved
Set to "0".
SW60 No. 8 Reserved
Set to "1".
SW61 No. 1 F.A.S.T. (RMS) mode
Used to determine a function of remote maintenance system (F.A.S.T.).
SW61 No. 2 Reserved
Set to "0".
SW61 No. 3 Verification stamp
End stamp:
It is set whether the red round mark is stamped at the bottom margin of
the document of every page in the memory input mode and document
sending mode or not.
SW61 No. 4 Day light saving
The day light saving function ON/OFF is set.
SW61 No. 5, No. 6 Key buzzer volume
Key buzzer volume:
The sound volume of key inputting buzzer and other buzzers is set.
SW61 No. 7, No. 8 Reserved
Set to "0".
SW62 No. 1, No. 2 Speaker volume
Speaker volume:
The sound volume of the speaker in the on-hook mode is set.
SW62 No. 3 Reserved
Set to "1".
SW62 No. 4 Reserved
Set to "0".
SW62 No. 5, No. 6 Ringer volume
Ringer volume:
The calling sound volume of CI signal receiving is set.
SW62 No. 7, No. 8 Reserved
Set to "0".
SW63 No. 1 Reserved
Set to "0".
SW63 No. 2 Reserved
Set to "1".
SW63 No. 3, No. 4 Reserved
Set to "0".
SW63 No. 5 Reserved
Set to "1".
SW63 No. 6 Reserved
Set to "0".
SW63 No. 7 Reserved
Set to "1".
SW63 No. 8 Reserved
Set to "0".
SW64 No. 1 Header registration
When setting this switch to "1", registering senders is protected.
SW64 No. 2 Reserved
Set to "0".
SW64 No. 3 Continuous serial polling
Turns ON/OFF the continuous polling function.
SW64 No. 4, No. 5 Time interval for continuous serial polling
Used to set the interval time for continuous serial polling. Normally set
to no interval (0 minute).
SW64 No. 6, No. 7 Reserved
Set to "0".
SW64 No. 8 Quick on line function
It is selected whether auto dial call is activated in the memory input
mode when one document is completely read or when all pages are
completely read.
SW65 No. 1, No. 2 Cassette selection
To set selective modes for detail paper cassettes of the printer.
00:
Manual
01:
Automatic 1
10:
Automatic 2
11:
Except the above
SW65 No. 3 ~ No. 5 The 1st priority cassette
To select the first priority cassette.
001:
1st paper feeder (MP-TRAY)
010:
2nd paper feeder
Except the above
Printing started from the possible paper feeder
SW65 No. 6 ~ No. 8 The 2nd priority cassette
To select the second priority cassette.
000:
Not used (To set in case of using only paper
feeder that has been set in the first priority
cassette)
001:
1st paper feeder (MP-TRAY)
010:
2nd paper feeder
Except the above
Not used
2 – 31
FO-4450U/FO-CS1
To select detail paper in the first prior-
ity cassette in accordance with setting
by SW65 3-8 and SW65 1-3. If the de-
tail paper in the first priority cassette
runs short, the second priority cassette
will be used.
To automatically select detail paper with
optimum size among the first to third
priority cassettes in accordance with
setting by SW65 3-8 and SW65 1-3.
The optimum paper is selected by every
page. If all the cassettes have the same
size paper, paper will be selected ac-
cording to the cassette priority.
To automatically select detail paper with
optimum size among the first to third
priority cassettes in accordance with
setting by SW65 3-8 and SW65 1-3. At
the start of printing, the optimum pa-
per is adopted only for the first page.
Thereafter the same cassette selected
for the first page will be used from the
second page and after. If all the cas-
settes have the same size paper, pa-
per will be selected according to the
cassette priority.
01: the same setting as in the case of
Automatic 1
Advertisement
Table of Contents
