Table of Contents
Advertisement
2. Diagnostic items description
2-1. Fax diagnosis
A) Soft switch mode
In this mode, the soft switch are set and the soft switch list is printed.
Soft switch mode screen
S O F T S W I T C H M O D E
S W 0 1 = 0 0 0 0 0 0 0 0
1 2 3 4 5 6 7
Switch
No.
1
Switch number selection
•
Press START key for setting of the next soft switch. If the soft
switch number is the final, pressing START key will exit the soft
switch mode.
•
Enter two digits of a soft switch number to set the switch number.
If a switch number of nonexistent soft switch is entered, key error
buzzer sounds to reject the input.
E N T E R L A S T D I G I T
S O F T S W I T C H M O D E
S W 0 1 = 0 0 0 0 0 0 0 0
S W 1
1
2
Cursor
Data number selection
The cursor position shows the data to be set.
Pressing # key or → key moves the cursor to the right. If, however,
the cursor is on data number 8, pressing # key or → key shifts the
cursor to data number 1 of the next switch number. If the switch
number is the final, pressing # key or → key will exit the soft switch
mode.
key or ← key moves the cursor to the left. If, however,
Pressing
the cursor is on data number 1, pressing
cursor to data number 1 of the former switch number. If the switch
key or ← key will not move the cursor and
number is 1, pressing
the error buzzer will sound.
3
Data setting method
Press the MENU key, and the data at the position of the cursor will be
reversed to 0 when it is 1, or to 1 when it is 0. (If the soft switch can
be changed at the bit (Refer to
the process not received.)
4
Outputting method of soft switch list
In the soft switch mode, press the REPORT key, and the soft switch
list will be output.
If the recording paper runs out or is clogged, the key error buzzer will
sound with the process not received.
5
Storage of data
In the following case, the data of the soft switches set will be stored.
•
It is shifted to set the next soft switch by pressing the START
switch.
•
It is shifted to set the next soft switch with the [#] key.
•
It is shifted to set the last soft switch with the [ ] key.
•
It is shifted to set another soft switch by inputting two digits as the
switch number. (When 2 digits are completely input.)
•
Output of the soft switch list is started.
6
Inhibition of data change
(This is also applicable for the optional setting.)
In the following case, it is inhibited to change the data with the key
error buzzer.
•
Switching ON/OFF of ECM during the use of image memory.
•
OFF to ON of telephone billing function which is using the image
memory is used (Note: In the existing set, the telephone billing
code function is specified from OFF to ON when the timer system
communication (including the batch communication) is set.)
Here, the memory is usable when the telephone billing code func-
tion is on. It can be set from ON to OFF while the memory is
used. However, if setting is practically changed even once, it can
not be returned from OFF to ON.
8
:DATA No.
Data
S O F T S W I T C H M O D E
S W 1 6 = 0 0 0 1 0 1 1 0
6
key or ← key shifts the
6
.), the error buzzer will sound with
•
OFF to ON of department control function during use of image
memory.
(Note: In the existing set, the department control function is set
from OFF to ON when the timer communication (including the
batch sending) or the memory hold is set.)
•
ON to OFF of continuous serial polling function when the con-
tinuous serial polling is started.
(Note: In the existing set, "ON to OFF of the continuous serial
polling function when the continuous serial polling is registered"
has been applied, but the conditions are now moderated. How-
ever, registration is impossible to the program of the new continu-
ous serial polling when the continuous serial polling function is
OFF.)
•
In addition, change of all soft switches during communication
B) Print area
According to the size of the specified sheet, the effective printing area is
printed.
C) ROM & RAM check
This is an item to check if the loaded memory device acts normally.
•
The memory devices shown in the following table are checked.
•
In case that an error occurs in the device check, the alarm buzzer
shown in the table sounds.
Check device and alarm buzzer
No.
Device checked
1
ROM (PROGRAM FLASH) <Short sound> 1 time
2
SRAM
3
Main D-RAM1 (*1)
4
D-RAM2 (*2)
5
—
*1: Work memory (SDRAM 8MB)
*2: Page memory (SDRAM 8MB)
(Example of display) In case that DRAM2 is erroneous.
Display during check
ROM SRM DRM1 DRM2
•
•
•
•
After the check is complete, the result is outputted.
D) Auto feeder mode
By executing the document insertion and discharge, the automatic feed-
ing function can be checked. And the document sensor can be checked
1
as well.
Set the document
Before pressing the "START" key, only the document sensor check is
carried out. And as the document sensor is ON, the document size
(A4/B4) and the sensor information (A4/B4/ORG) are displayed.
AUTO FEEDER MODE
(
After setup of the document
AUTO FEEDER MODE
B4 (A4 B4 ORG)
2
The automatic feeding starts by pressing the "START" key. This mode
ends when the document ends, and the result is printed.
2 – 3
FO-4450U/FO-CS1
Number of buzzer sound
Remarks
<Short sound>:
<Short sounds> 2 times 0.5 sec.ON / 0.5 sec.OFF
<Short sounds> 3 times <Long sounds>:
<Short sounds> 4 times 1.0 sec.ON / 0.5 sec.OFF
—
Display after check
ROM SRM DRM1 DRM2
P
P
P
P=PASS
E=ERROR
)
Only the sensor which is
activated (fallen down) is displayed.)
The paper sheet size (A4/B4) is
displayed.
E
Advertisement
Table of Contents
