Board Components - Electrolux EI15IM55GS Service Manual

Quick Reference Card
E9 Thermister 4 open or shorted.
Échelon Model Selection:
E11 EE Memory error.
1. Plug in unit.
P1 Pump circuit open.
2. The display may show a SP or --, either is OK.
3. Install a jumper on J3.
4. Hold down warmer, colder,and light button until

Board Components

display shows model numberand main board beeps.
5. Use warmer/colder to select new model number.
61-2175R 120V 74-2115WC 220V
62-2175WC 120V 75-2175R 220V
63-2175BEV 120V EI151M55GS 76-2175WC 220V
64-CO2175F 120V 77-2175BEV 220V
65-2175RF 120V 78-CO2175 220V
Pin 7 Pin 6
66-CO2175DWR 120V 79-2175RF 220V
67-CLR2160 120V 80-CO2175DWR 220V
68-CLRCO2175 120V 81-CLR2160 220V
C_Fan Lights
70-2175DWR 120V 82-CLRCO2175 220V
71-2115R 120V 85-2275DWRWS 120V*
Relay 1 Relay 2
72-2115WC 120V 86-2275DWRWS 220V*
73-2115R 220V
6. Press and release light key.
EI151M55GS
7. Wait for display to stop flashing.
8. Remove jumper from board.
Model Thermister
9. Unplug unit and wait 5 seconds.
10. Plug unit back in.
* Note: Models 2275DWRWS cannot be programmed on the
EI151M55GS
same board as the other models.
#
1 L g i t h l l a L E D
2 Thermistor #1 status (Temp, E1 or E2)
3 E r r r o o l g
4 D f e o r t s n i o f
5 Compressor runtime (based on last cycle)
6 Defrost Length (adjustment - up to 99 minutes)
7 Light switch status (0 or 1)
8 Display toggle status (0 or 1)
9 R s e o t e r f c a o t
10 Adjust thermistor #1 offset (-10 to +10)
1 1 D a a t d o w n o l a
1 2 C e l r a e r r r o o l g
1 3 C e l r a d o w n o l a
1 4 M o d l e n u m b r e
24
Model
2 1 7 5 R
2 1 1 5 R
2 1 1 5 W C
2 1 7 5 D W R R
CO2175F
Pin 5 Pin 4
2175RF
H_H20
CO2175DWR
Relay 3 Relay 4
CLR2160
CLRCO2175
Thermister
1 2
2 1 7 5 B E V
2275DWRWS
N/A IB
E1 Thermistor #1 open
E2 Thermistor #1 shorted
E3 Door #1 open longer than 20 minutes
E5 Thermistor #1 out of range (+10) for more than 12 hours
E6 Thermistor #1 out of range (-10) for more than 12 hours
E7 Thermistor #2 open or shorted
E8 Thermistor #3 open or shorted
E9 Thermistor #4 open or shorted
E10 Door #2 (drawer) open longer than 20 minutes
E11 EE Memory Error
P1 Pump circuit open due to high water level in ice bin
S e g m e n s t
y r d e a f u s t l
d
d m e m o y r
d s i l p y a
Service Information
All errors or combination show up as ER alternating
R E L A Y R E F E R E N C E C H A R T
with SP. P1 will alternate with SP and ICE for
PIN 7 PIN 6
Part
C_FAN LIGHTS
Number models 67/68. E3 and E10 both have audible
Relay 1 Relay 2 Relay 3
alarms. P1 does not have an audible alarm.
Compressor/
6 1 7 / 5 L g i t h
Compressor/
7 1 7 / 3 L g i t h
Compressor/
7 2 7 / 4 L g i t h
Compressor/
7 0 L g i t h 1
Cond Fan
Light Compressor
64/78 Pin 3
E FAN
Cond Fan
65/79 Light Compressor
E FAN
C_Pump
Cond Fan
66/80 Light Compressor
E FAN
Relay 5
67/81 Cond Fan Compressor
68/82 Cond Fan Light Compressor
Thermister Thermistor
Compressor/
3 4
6 3 1 7 7 L g i t h
85186 Cond Fan Bottom Light Compressor
N/A CON
# Description
1 5 A d u j t s h t r e m t s i r o #
16 Adjust thermistor #2 offset
1 7 A d u j t s h t r e m t s i r o #
1 8 A d u j t s h t r e m t s i r o #
19 View thermistor #2 status
20 View thermistor #3 status
21 View thermistor #4 status
22 Automatic toggle through relays (switch on and off)
2 3 D f e o r t s n i e t v r l a a d u j
24 Adjust thermistor #2 setpoint
2 5 A d u j t s h t r e m t s i r o #
2 6 A d u j t s h t r e m t s i r o #
2 7 D s i l p y a s f o w t a e r e v
9 9 E x t i
PIN 4 PIN 3 PIN 2
PIN 5
H_H2O C_PUMP R_VALVE
Relay 4 Relay 5 Relay 6
Fan
Fan
Fan
Pan Heat Mull Heat
Fan
Hot Gas
DRAIN HEAT IM 1
Pin 2 Pin 1
Valve
Hot Gas
DRAIN HEAT
Valve
R_Valve BP_Valve
Hot Gas
MULL HEAT IM 1
Valve
Relay 6 Relay 7
Hot Gas
Circulation
Valve/ Water
Pump
Valve
Hot Gas
Circulation
Valve/Water Ref Valve
Pump
Valve
Door Door
Switch 1 Switch 2
Fan
Top Light Bottom Valve
N/A P60
1 i d e f f e r t n l a i
3 o s f f t e
4 o s f f t e
t s 3 ( o t 2 4 h o r u ) s
3 s e p t i o t n
4 s e p t i o t n
s r o i n
9
PIN 1
BP_VALVE
Relay 7
IM 2
IM 2
Ref Bypass
Valve
Top Valve