Keypad Options; On/Off; Showroom Mode - Electrolux EI15IM55GS Service Manual

6
Installation / General Instructions
Adjusting Door Alignment
1. Loosen (do not remove) top and bottom hinge screws
Adjusting Door Alignment
Adjusting Door Alignment
(Figure 11 and Figure 12).
1.
Loosen (do not remove) top and bottom
1. Loosen (do not remove) top and bottom hinge screws
hinge screws (Figures 9 and 10).
(Figure 11 and Figure 12).
2. Align door squarely with cabinet. Make sure
gasket is firmly in contact with cabinet all the
2. Align door squarely with cabinet. Make sure gasket is
way around the door (no gaps).
firmly in contact with cabinet all the way around the
3. Tighten bottom hinge screws.
door (no gaps).
2. Align door squarely with cabinet. Make sure gasket is
4. Tighten top hinge screws.
firmly in contact with cabinet all the way around the
3. Tighten bottom hinge screws.
door (no gaps).
4. Tighten top hinge screws.
3. Tighten bottom hinge screws.
4. Tighten top hinge screws.
Figure 9
ULIN_0293_A
Figure 11
ULIN_0293_A
Figure 11
Figure 10
ULIN_0104_A
Figure 12
ULIN_0104_A
Figure 12
7 Adjust Drawer

Keypad Options

7 Adjust Drawer
Checking Drawer Alignment
WARNING
The unit's drawers are aligned at the factory before
Checking Drawer Alignment
shipment. However, their alignment could have been
Electrocution can cause death or serious
disturbed during shipment or during overlay panel
The unit's drawers are aligned at the factory before
injury. Take precautions when touching a
installation.
shipment. However, their alignment could have been
bare circuit board. Wear an anti-static wrist
disturbed during shipment or during overlay panel
strap and ground it to an electrical ground or
installation.
Front-to-Back
grounded water pipe. Handle circuit boards
carefully and avoid touching components.
Aligned
Front-to-Back
When touching key combinations in which
you hold one key and press another key three
times, it is important to carefullt follow this
procedure:
1. Hold the desired key ensuring the light above
the key is lit.
2. Press the other key three times, ensuring it
lights up each time.
3. Release the held key only after releasing the
pressed key for the third time.
Except as noted, these functions are available
on all models.
Aligned
Top-to-Bottom

ON/OFF

Aligned
The ON/OFF mode allows the unit to be turned
Top-to-Bottom
on and off via the keypad. To do this, hold the key
See Figure 13. Check each drawer to confirm that it is
for approximately 10 seconds until the "F" begins aligned:
to flash. Release the key and the unit will switch
See Figure 13. Check each drawer to confirm that it is
• Side-to-Side — When viewed from the top, the
modes.
aligned:
drawer front should be square with the sides of the
cabinet.
This mode does not disconnect power from the
• Side-to-Side — When viewed from the top, the
• Front-to-Back — When viewed from the side, the
circuit board si it is still "LIVE". Turning the unit off drawer front should be square with the sides of the
drawer front should be straight with the cabinet's
cabinet.
while in Clean, Ice Maker Off, Forced Harvest,
sides, not cocked forward or back.
or Forced Defrost will cancel those modes. If this
• Front-to-Back — When viewed from the side, the
• Top-to-Bottom — When viewed from the front, the
drawer front should be straight with the cabinet's
mode is entered while the unit is in an ice-making
drawer should be level horizontally.
sides, not cocked forward or back.
harvest mode, it will continue it's cycle and flash
"OFF" until completed.
• Top-to-Bottom — When viewed from the front, the
If both drawers are properly aligned, no further
drawer should be level horizontally.
adjustment is necessary. If either drawer is not aligned,

Showroom Mode

carefully follow instructions to remove that drawer, make
If both drawers are properly aligned, no further
This mode is designed to show units in a display
the necessary adjustment and re-install the drawer.
adjustment is necessary. If either drawer is not aligned,
environment. When in this mode the only functions
carefully follow instructions to remove that drawer, make
will be the controls and cabinet lights. The
the necessary adjustment and re-install the drawer.
compressor, fans, etc. will not operate. To enter this
mode, hold the down arrow and press the LIGHT
button three times. When entered, the unit will beep
once and the degree symbol will be to flash. When
the degree symbol is flashing the unit will allow
the use of the control for demonstrations. After not
touching the unit for one minute the display will
begin to "snake" around. This is meant to alert you
the unit is in showroom mode. The unit can be left
in this mode indefinitely. If you again want to demo
Aligned
Aligned
Side-to-Side
Aligned
Side-to-Side
ULIN_0312_A
Figure 13
ULIN_0312_A
Figure 13
15
15