Scale Competition; Additional Items Required; Hardware & Accessories; Adhesives & Building Supplies - Top Flite Cessna 182 ARF User Manual

(Note: Both of the above referenced batteries are
required and should be connected in series. One
18.5V pack will NOT work because it will not fit
into the battery compartment.)
• Great Planes Series Deans U 2 to 1 adapter
®
(GPMM3143)
• Great Planes Velcro ® Hook & Loop 1 x 6" (2)
(GPMQ4480)
• Great Planes ElectriFly Equinox
Balancer 2–5 cell (GPMM3160)
A charger compatible with LiPo batteries such as:
• Great Planes PolyCharge4 DC 4 Output LiPo
™
Charger (GPMM3015)
(Note: Since the Great Planes PolyCharge4
charger is capable of charging four LiPo battery
packs simultaneously, it is recommended to
purchase an Equinox cell balancer for each
battery pack in order to minimize charge times
between flights.)
• APC 16 x 8 Thin Electric Propeller (APCQ4015)

SCALE COMPETITION

Though the Top Flite Cessna 182 ARF may not have
the same level of detail as an "all-out" scratch-built
competition model, it is a scale model nonetheless
and is therefore eligible to compete in the Fun Scale
class in AMA competition (we receive many favorable
reports of Top Flite models in scale competition!). To
receive the five points for scale documentation, the only
proof required that a full size aircraft of this type in your
paint/markings scheme did exist is a single sheet such
as a kit box cover from a plastic model, a photo, or a
profile painting, etc. If the photo is in black and white
other written documentation of color must be provided.
Contact the AMA for a rule book with full details.
If you would like photos of the full-size Cessna 182
for scale documentation, or if you would like to study
the photos to add more scale details, photo packs are
available from:
E-mail: www.bobsairdoc.com

ADDITIONAL ITEMS REQUIRED

LiPo Cell
™
HARDWARE & ACCESSORIES
In addition to the items listed in the "Decisions You
Must Make" section, following is the list of hardware
and accessories required to finish the Cessna 182
ARF. Order numbers are provided in parentheses.
o
R/C foam rubber (1/4" [6mm] - HCAQ1000,
or 1/2" [13mm] - HCAQ1050)
o
3' [900mm] Standard silicone fuel
tubing (GPMQ4131)
ADHESIVES & BUILDING SUPPLIES
In addition to common household tools (screwdrivers,
drill, etc.), this is the "short list" of the most important
items required to build the Cessna 182 ARF. We
recommend Great Planes Pro
o
1/2 oz. [15g] Thin Pro CA (GPMR6001)
o
Pro 30-minute epoxy (GPMR6047)
o
Drill bits: 1/16" [1.6mm], 5/64" [2mm], 3/32"
o
8-32 Tap and drill set (GPMR8103) (glow engine
installation only)
o
Great Planes Pro Threadlocker (GPMR6060)
o
#1 Hobby knife (HCAR0105)
o
#11 Blades (5-pack, HCAR0211)
o
Medium T-pins (100, HCAR5150)
o
Masking tape (TOPR8018)
o
Denatured alcohol (for epoxy clean up)
o
Panel line pen (TOPQ2510)
o
Hobbico pin vise 1/16" Collet w/6 bits (HCAR0696)
o
J&Z R/C-56 glue 4 oz (JOZR5007)
o
Hobbico 5-1/2" curved tip canopy
scissors (HCAR0667)
Bob's Aircraft Documentation
3114 Yukon Ave
Costa Mesa, CA 92626
Telephone: (714) 979-8058
Fax: (714) 979-7279
™ CA and Epoxy glue.
[2.4mm], 3/16" [4.8mm]
4
o
220-grit Sandpaper
o
Small clamps
o
Petroleum jelly
o
Oil
OPTIONAL SUPPLIES & TOOLS
Here is a list of optional tools that may help you build
the Cessna 182 ARF.
o
21st Century sealing iron (COVR2700)
®
o
21st Century iron cover (COVR2702)
o
21st Century trim seal iron (COVR2750)
o
1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
o
1/2 oz. [15g] Thick Pro CA- (GPMR6013)
o
Pro 6-minute epoxy (GPMR6045)
o
Small metal file
o
Stick-on segmented lead weights (GPMQ4485)
o
2 oz. [57g] spray CA activator (GPMR6035)
o
4 oz. [113g] aerosol CA activator (GPMR6034)
o
CA applicator tips (HCAR3780)
o
CA debonder (GPMR6039)
o
(6) Epoxy brushes (GPMR8060)
o
Mixing sticks (GPMR8055)
o
Mixing cups (GPMR8056)
o
Pliers with wire cutter (HCAR0630)
o
Compressed air 10 oz (TAEC1060)
o
Switch & charge jack mounting set (GPMM1000)
o
Ernst charge receptacle Futaba J (ERNM3001)
o
Rotary tool such as Dremel
®
o
Rotary tool reinforced cut-off wheel (GPMR8200)
o
Servo horn drill (HCAR0698)
o
Hobby Heat micro torch (HCAR0755)
™
o
Dead Center ™ engine mount hole
locator (GPMR8130)
o
AccuThrow deflection gauge (GPMR2405)
™
o
C.G. Machine ™ (GPMR2400)
o
Precision magnetic prop balancer (TOPQ5700)
o
Hobbico flexible 18" ruler stainless
steel (HCAR0460)
o
Hobbico 8-piece ball tip hex "L" wrench
(SAE, HCAR0520)
o
Hobbico 7-piece ball tip hex "L" wrench
(metric, HCAR0521)