1. Manuals
  2. Brands
  3. DKS Manuals
  4. Gate Opener
  5. 9310
  6. Owner's manual

DKS 9310 Owner's Manual

Vehicular slide gate operator
Hide thumbs Also See for 9310:
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual
P/N 9310-065 Rev H 8/08
Copyright 2003 DoorKing, Inc. All rights reserved.
Vehicular Slide Gate Operator
Inglewood, California 90301
Model 9310
DoorKing, Inc.
120 Glasgow Avenue
U.S.A.
Phone: 310-645-0023
Fax: 310-641-1586
www.doorking.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 9310 and is the answer not in the manual?

Questions and answers

Related Manuals for DKS 9310

Summary of Contents for DKS 9310

  • Page 1 Owner’s Manual Model 9310 Vehicular Slide Gate Operator DoorKing, Inc. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Phone: 310-645-0023 Fax: 310-641-1586 www.doorking.com P/N 9310-065 Rev H 8/08 Copyright 2003 DoorKing, Inc. All rights reserved.
  • Page 2 Page 2 9310-065-H-8-08...
  • Page 3 Use this manual with the following models only. All 9310 models with circuit board 4403-010. IMPORTANT! The 4403 circuit board used in the model 9310 IS NOT interchangeable with the 4402 circuit board used in the earlier model 9300 operators.
  • Page 4 See page 36. Adjust both open and close inherent reverse sensitivity. NOTE: Operator will assume a "soft shutdown" during sensitivity adjustments. This will require operator open input to be activated to resume normal operation. See page 37. Page 4 9310-065-H-8-08...
  • Page 5 19. The black motor wire is routed through the donut with the number of turns shown in the table. Refer to the wire diagrams in the back of the manual. SENSITIVITY EXIT LOOP 9310-065-H-8-08 Page 5...
  • Page 6 ENTRAPMENT: The condition when an object is caught or held in a position that increases the risk of injury. Page 6 9310-065-H-8-08...

  • Page 7: Entrapment Protection

    Inherent adjustable clutch or pressure relief device. TYPE D: Provision for connection of, or supplied with, an actuating device requiring continuous pressure to maintain opening or closing motion of the gate. TYPE E: An inherent audio alarm. 9310-065-H-8-08 Page 7...

  • Page 8: Loop

    Do not allow children to play in the area of the operator or to play with any gate-operating device. • To remove the gate operator from service, operate the gate to the full open position and then shut off power to the operator at the service panel. Page 8 9310-065-H-8-08...

  • Page 9: H-8-08 Page

    SAVE THESE INSTRUCTIONS! Gate Construction Vehicular gates should be constructed and installed in accordance with ASTM F2200; Standard Specification for Automated Vehicular Gate Construction. For a copy of this standard, contact ASTM directly at 610-832-9585; service@astm.org; or www.astm.org. 9310-065-H-8-08 Page 9...

  • Page 10: Instructions Regarding Intended Installation

    One or more non-contact sensors shall be located where the risk of entrapment or obstruction exist, such as the perimeter reachable by a moving gate or barrier. Page 10 9310-065-H-8-08...
  • Page 11 A wireless contact sensor shall function under the intended end-use conditions. One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm). 9310-065-H-8-08 Page 11...

  • Page 12: Slide Gate Requirements

    2 ¼ inches. Install a filler or barrier in this area to reduce this gap to 2 ¼ inches or less. Install a contact sensor (type B2) on the fence to help minimize the risk of entrapment in this area. Page 12 9310-065-H-8-08...

  • Page 13: Slide Gate Protection

    Warning signs are to be placed on each side of the Open Loop gate so that they are easily visible from either side (Optional) of the gate. A separate pedestrian access located so pedestrians cannot come in contact with the vehicular gate. 9310-065-H-8-08 Page 13...

  • Page 14: Table Of Contents

    Shutdown Conditions 4.2.1 Soft Shutdown ..........................40 4.2.2 Resetting a Soft Shutdown.......................40 4.2.3 Hard Shutdown.........................41 4.2.4 Resetting a Hard Shutdown .....................41 Manual Gate Operation 4.3.1 Emergency Vehicle Access Conditions..................42 4.3.2 Fail-Safe Manual Operation .....................42 4.3.3 Fail-Secure Manual Operation ....................43 Page 14 9310-065-H-8-08...

  • Page 15: H-8-08 Page

    ½ HP 115 VAC Wire Diagram ........................50 ½ HP 208/230/460 VAC Wire Diagram ....................51 1 HP 115 VAC Wire Diagram ........................52 1 HP 208/230 VAC Single Phase Wire Diagram..................53 1 HP 208/230 VAC Three Phase Wire Diagram ..................54 9310-065-H-8-08 Page 15...
  • Page 16 Page 16 9310-065-H-8-08...

  • Page 17: Section 1 - Installation

    Note 1: Assumes gate is in good working condition installed on a level surface. Note 2: Operators with Convenience Open Option 800 Lbs. (1/2 HP), 1300 Lbs. (1 HP) 28.5 (1 HP) 16.5 21.5 (1/2 HP) 9310-065-H-8-08 Page 17...

  • Page 18: Concrete Pad

    Concrete Pad The model 9310 vehicular gate operator is designed to be mounted on a concrete pad. 1. Construct a form for the mounting pad according to the specifications shown below. Note that the pad for the 1 HP operator extends an additional 6 inches to the right to accommodate the larger cover.

  • Page 19: Operator Installation

    We recommend 1/2 x 2 or 3/8 x 2 sleeve anchors (not supplied). After drilling the mounting holes, clean them out and install the sleeve anchors. Position the operator over the anchors and tighten. 9310-065-H-8-08 Page 19...

  • Page 20: Chain Installation

    6. If the operator is to be rear mounted, an endless idler assembly (P/N 2600-818) is required. Depending on the length of the gate, additional chain may also be required. See detail on page 18. Page 20 9310-065-H-8-08...

  • Page 21: Front Mount Installation

    Front Mount Installation REMOVE BREATHER PLUG PIN CONCRETE PAD GROUND LEVEL 9310-065-H-8-08 Page 21...

  • Page 22: Rear Mount Installation

    Rear Mount REMOVE BREATHER PLUG PIN CONCRETE PAD GROUND LEVEL Gate Brackets Idler Assembly P/N 2600-818 Page 22 9310-065-H-8-08...

  • Page 23: Warning Sign Installation

    Serious Injury or Death KEEP CLEAR! Gate may move at any time without prior warning. Do not let children operate the gate or play in the gate area. This entrance is for vehicles only. Pedestrians must use separate entrance. 9310-065-H-8-08 Page 23...
  • Page 24 Page 24 9310-065-H-8-08...

  • Page 25: Section 2 - Wiring

    • Use separate conduits for high and low voltage. • We suggest that minimum ¾-inch conduit be used. • Be sure that all conduits are installed in accordance with local codes. 9310-065-H-8-08 Page 25...

  • Page 26: High Voltage Connections

    ½ - 1 HP - 115 VAC Power ½ HP - High Voltage 3 Power 1 HP - High Voltage 3 Power 208/230/460 208/230 VAC 3 Ph VAC 3 Ph GREEN BLACK WHITE GREEN GREEN BLACK BLACK BLACK BLACK BLACK BLACK Page 26 9310-065-H-8-08...

  • Page 27: Control Wiring

    Partial open input. Devices connected here will open the gate to 14-feet only. Reverse input functions only when gate is in the closing cycle. Must use a DoorKing 3-button control station. Others will not work. DOORKING, INC., INGLEWOOD, CA 90301 Model 9310 Title: Control and Secondary Device Wiring Date: 5/07 Dwg.

  • Page 28: Loop Detector Wiring

    Reverse Exit Exit Loop Reverse Loop From outside From inside Detail A Reverse loop Reverse loop TB 1 Detail A DOORKING, INC., INGLEWOOD, CA 90301 Title: Model 9310 Loop Detector Wiring Date: 5/07 Dwg. No. 4403-LOOP-1 Rev. Page 28 9310-065-H-8-08...

  • Page 29: Auxiliary Device Wiring

    Common White DoorKing 1404-080 Green Remote Reset Switch CAUTION High Voltage 2351-010 Circuit Board DoorKing 2351-010 Tracker Expansion Board DOORKING, INC., INGLEWOOD, CA 90301 Model 9310 Title: Auxiliary Device Wiring Diagram Date: 5/07 Dwg. No. 4403-AUXDEV-1 Rev. 9310-065-H-8-08 Page 29...

  • Page 30: Primary / Secondary (Bi-Parting) Gate Wiring

    Reverse Loop Common Common Common Common Reverse Loop Exit Loop Green Green Primary Secondary Operator Operator DoorKing 9409-010 Conduit DOORKING, INC., INGLEWOOD, CA 90301 Title: Model 9310 Primary / Secondary Wiring Diagram Date: 7/07 Dwg. No. 4403-DUAL-1 Rev. Page 30 9310-065-H-8-08...

  • Page 31: Terminal Identification And Description

    Normally Open (NO) or Normally Closed (NC) operation. Contact rating is 1 amp maximum at 24 Volts. DRY RELAY CONTACT 24 VOLT COMMON Same as terminal 1. ALARM OUTPUT ALARM RESET SOLENOID LOCK MOTOR WARNING MOTOR HIGH VOLTAGE! 115 VAC HOT 115 VAC NEUTRAL 9310-065-H-8-08 Page 31...

  • Page 32: Secondary Device Terminal

    If an open edge sensor is activated prior to the gate reaching the full open position, the gate will stop and enter a soft shutdown condition. 5. COMMON Common terminal for the secondary entrapment protection device inputs. 6. COMMON Page 32 9310-065-H-8-08...

  • Page 33: Section 3 - Adjustments

    1 HP 208 / 3 5 See wire diagram: 1 HP 230 / 3 5 4403-1-202346-3 REVERSE SENSOR CLOSE OPEN MIN MAX MIN MAX DOORKING, INC., INGLEWOOD, CA 90301 Title: 4403 Control Board Adjustments Date: 8/08 Dwg. No. M9310-065-8 Rev. 9310-065-H-8-08 Page 33...

  • Page 34: Switch Settings

    Changing the setting of this switch without physically changing the lock assembly will damage the operator. 2. Do not run the self-test while the gate operator is connected to the gate. This self-test feature is designed for bench-testing only. Page 34 9310-065-H-8-08...

  • Page 35: Programming Switch Description And Function

    Switch 3: Sets the circuit board to function with slide gate operators (switch OFF) or overhead gate operators (switch ON). This switch must be left in the OFF position for model 9310 Slide Gate Operator. Switch 4: This switch should be left in the OFF position when the slide gate is running on a level or small incline track and the gate does not coast.

  • Page 36: Limit Switch Adjustment

    Slide to Adjust Partial Open Limit IMPORTANT! 3-Phase Power Limit Switch Test This test MUST be performed if the 9310 is powe red from a 3-phase power source. Activate the operator and watch the limit nut movement. Manually activate the limit switch that the limit nut is movi ng towards.

  • Page 37: Reverse Sensitivity Adjustment

    1 and 4 as in step 1 to reactivate the automatic close timer. 7. You may have to repeat step 2 several times to find the correct sensitivity adjustment. 9310-065-H-8-08 Page 37...
  • Page 38 Page 38 9310-065-H-8-08...

  • Page 39: Section 4 - Operating Instructions

    The AC POWER toggle switch turns power to the operator ON (toggle up) or OFF (toggle down). The DC POWER toggle switch (units equipped with POWER the backup option only) turns power to the DC backup system ON (toggle up) or OFF (toggle down). 9310-065-H-8-08 Page 39...

  • Page 40: Shutdown Conditions

    "intended input" includes any command, any standard safety input and any loop input. Activating any of these inputs will reset the gate. At that point the gate will return to normal operation. If the gate is open, the automatic close timer will then time out and close the gate. Page 40 9310-065-H-8-08...

  • Page 41: Hard Shutdown

    Activation of a close command will run the gate to the closed position. NOTE: The gate operator will not lose its limit settings when a hard shutdown occurs. 9310-065-H-8-08 Page 41...

  • Page 42: Manual Gate Operation

    For manual fail-safe gate operation, turn power to the operator OFF. If a backup power system is in use, be sure that this power is turned OFF also. Once power is OFF, the gate can be manually operated. Page 42 9310-065-H-8-08...

  • Page 43: Fail-Secure Manual Operation

    Be sure that primary (AC) and backup (DC) power is removed or shut-off prior to placing the gate operator in manual operation. Insert the manual release key into the keyed release on the side of the gate operator, and turn it clockwise 1/4 turn. The gate can now be manually operated. 1/4 TURN 9310-065-H-8-08 Page 43...
  • Page 44 Page 44 9310-065-H-8-08...

  • Page 45: Maintenance Schedule

    Release Check manual release for proper operation. Secondary Check that secondary (external) reverse device(s) stop or reverse Reverse Device the gate when activated. Sprockets Check set-screws for tightness. Complete Complete check of gate and gate operating system. 9310-065-H-8-08 Page 45...

  • Page 46: Operator Diagnostics

    Current Sensor Donut Motor Volt / Ph Turns ½ HP Ø 1 HP 115 / 208 / 230 1 Ø 1 HP 208 – 3 Ø 1 HP 230 – 3 Page 46 9310-065-H-8-08...

  • Page 47: Trouble Shooting

    If the motor runs in both steps above, replace the control board. If the motor does not run, or runs in only one direction, problem can be a bad motor, motor capacitor, wire connections from the control board to the motor or a bad control board. 9310-065-H-8-08 Page 47...
  • Page 48 • There may be a problem with the current sensor on the circuit board. Replace the circuit Operator runs for 1 board. second and stops, two short beeps are heard. Page 48 9310-065-H-8-08...

  • Page 49: Accessories

    5.4 Accessories The following accessory items can be used with the model 9310 slide gate operator. Contact Sensor Contact sensors for use as a secondary entrapment protection device. Miller Edge, Inc. ME120, ME123, MG020, MGR20, MGS20 Photo Cell Non-contact (photo cells) sensors for use as a secondary entrapment protection device.

  • Page 50: ½ Hp 115 Vac Wire Diagram

    Convenience Outlets White Black White Black Black Operator Power Chassis Ground Black 115 VAC DOORKING, INC., INGLEWOOD, CA 90301 White Input Title: Model 9310 Wire Diagram Green ½ HP 115 VAC Date: 5/05 Dwg. No. 4403-05-115-1 Rev. Page 50 9310-065-H-8-08...

  • Page 51: ½ Hp 208/230/460 Vac Wire Diagram

    2 power legs and Black Input cap the third. Blue Green Black 460V Brown DOORKING, INC., INGLEWOOD, CA 90301 White Title: Model 9310 Wire Diagram ½ HP 208/230/460 VAC Black/White Date: 5/05 Dwg. No. 4403-05-202346 Rev. 9310-065-H-8-08 Page 51...

  • Page 52: Hp 115 Vac Wire Diagram

    Convenience Outlets White Black White Black Black Operator Power Chassis Ground Black 115 VAC DOORKING, INC., INGLEWOOD, CA 90301 White Input Title: Model 9310 Wire Diagram Green 1 HP 115 VAC Date: 12/07 Dwg. No. 4403-1-115-1 Rev. Page 52 9310-065-H-8-08...

  • Page 53: Hp 208/230 Vac Single Phase Wire Diagram

    Black Blue Black 230V Brown Black 208/230 V White Black Single Phase Black/White Input Green DOORKING, INC., INGLEWOOD, CA 90301 Title: Model 9310 Wire Diagram 1 HP 208/230 VAC Single Phase Date: 12/07 Dwg. No. 4403-1-2023-1 Rev. 9310-065-H-8-08 Page 53...

  • Page 54: Hp 208/230 Vac Three Phase Wire Diagram

    208 V White Black White Black 230 V Black 208/230 V Black Three Phase Black Input Green DOORKING, INC., INGLEWOOD, CA 90301 Title: Model 9310 Wire Diagram 1 HP 208/230 VAC Three-Phase Date: 8/08 Dwg. No. 4403-1-202346-3 Rev. Page 54 9310-065-H-8-08...
  • Page 55 9310-065-H-8-08 Page 55...

Table of Contents