Panasonic KX-FP101AL Service Manual page 83

2.4.4. SERVICE FUNCTION TABLE
Code Function
501 Pause time set
502 Flash time set
503 Dial speed select
511 Vox sense
514 Bell detect time set
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
550 Memory clear: To reset the value to the default one, except the top margin (853)
and left margin (854).
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
561 KEY test
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
593 Time between CED and 300bps
Set Value Effective Range
X 100 msec 001~600
01~99 X 100 msec 01~99
1:10 pps 2:20 pps 1, 2
1:High 2:Low 1, 2
1~9 X 100 msec 1~9
1:2100 Hz 2:1100 Hz 1, 2
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1:0.0km / 2:1.8km 1~4
3:3.6km / 4:7.2km
1:ON 2:OFF 1, 2
1: OFF 2:PHASE B 1~3
3:ALL
1:ON 2:OFF 1, 2
1:61% 2:67% 1, 2
X number of times 00~99
X second 001~999
X number of rings 01~99
X number of times 00~99
X second 001~999
1: OFF 2:ALL 1~3
3:AUTO
1: 75 msec 2:500 1~3
msec 3:1 sec
83
Default Remarks
30 ----------------
100 ----------------
1 ----------------
1 When the TAM or EXT TAM
does not stop recording the
ICM because noise is detected
on the telephone line, change
this setting to "LOW".
600 ----------------
1 See Symptom/
Countermeasure Table for
long distance and international
calls in 2.3.3.1. Defective
Facsimile Section.
1 See Symptom/
Countermeasure Table for
long distance and international
calls in 2.3.3.1. Defective
Facsimile Section.
1 The resolution reverts to the
default when transmission is
complete.
2 When the telephone station is
far from the unit or reception
cannot be performed correctly,
adjust accordingly.
1 ----------------
"START" input"
2 See 2.5. TEST FUNCTIONS.
1 Sets whether to monitor the
line signal with the unit´s
speaker during FAX
communication or not.
See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
0 See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
1 See 2.2.1. Paper Jam.
See 2.5. TEST FUNCTIONS.
2 Sets the % break of pulse
dialing accordingly PBX.
00 Selects the number of time that
ITS is redialed (not including
the first dial).
65 Sets the interval of ITS
redialing.
15 Sets the number of rings
before the unit starts to receive
a document in the TEL mode.
2 Selects the number of redial
times during FAX
communication (not including
the first dial).
65 Sets the FAX redial interval
during FAX communication.
2 Lets you select the CNG output
during FAX transmission. ALL:
CNG is output at phase A.
AUTO: CNG is output only
when automatic dialing is
performed. OFF: CNG is not
output at phase A.
1 See Symptom/
Countermeasure Table for
long distance and international
calls in 2.3.3.1. Defective
Facsimile Section.
KX-FP101AL