Alphabet Input And Mouse Pointer; Entering Characters With The Software Keyboard; (Using A Mouse); Operating The Mouse Pointer From The Front Panel For Character Entry (Without Using A Mouse) - JVC VR-N900U Instructions Manual

Preparation
CAUTION
• Connect the IP camera after having turned off the system
and connected devices.
• Set the IP address of camera to 192.168.0.xxx. When
setting the IP address
192.168.0.xxx, you must also change the IP address of
LAN1. As for the modification method of the camera's IP
address, refer to the instruction manual of each camera.
• Do not connect LAN1 to the internet. If the internet is busy
or the relay equipment fails, you may not be able to save
important camera images. To maintain full recording
capacity, it is recommended that a dedicated network be
used. Be sure to connect the LAN1 camera network to the
same segment. (Do not use the address translation of
NAT and NAPT etc. or a router.)
• If you connect LAN2 to the internet from a surveillance
computer, you will need to configure IP Masquerading.
• Communication between LAN1 and LAN2 is not possible.
Nor is it possible to configure a camera connected to
LAN1 from the surveillance computer connected to LAN2.
In order to configure a camera connected to LAN1, it is
necessary to connect the computer for configuring
cameras to LAN1.
• LAN1 and LAN2 are incompatible with QoS. Sound may not
be played normally depending on the condition of the circuit.
• The default LAN1 IP address is 192.168.0.253 and the
default LAN2 IP address is 192.168.1.253. You can
change the address in the [OS Setting] window.
Page 59) In the VR-N900U, analog input circuitry is
considered as a network encoder (IP video server) and
the IP address 192.168.201.12 is set by default. To
change the LAN1 or LAN2 IP address, specify an address
other than 192.168.201.0 - 192.168.201.255. Make sure
that you do not use the same segment in the LAN1 and
LAN2 addresses.
• If a single IP camera is registered to multiple VR-N900U
units, recording may not be carried out normally or
improper camera operations, such as PTZ control, may
result. It is recommended that a single IP camera is
registered and controlled for PTZ operations by a single
VR-N900U.
• Be sure not to connect a broken hub, router or
deteriorated network cable etc. The system may not
operate properly.
• It is not recommended to connect to a keyboard.

Alphabet Input and Mouse Pointer

You can enter letters of the alphabet and move the mouse
pointer using the buttons on the front panel, but it is easier
to make complicated settings and enter letters if you
connect a mouse.
• It is not recommended to connect to a keyboard.
6
of camera other than
☞
(
Entering Characters with the Software
Keyboard (Using a Mouse)
You can use the software keyboard to enter letters of the
alphabet with the mouse.
1
Press the [KEY] button.
• The software keyboard will appear.
• Press the [KEY] button again to close the software
keyboard.
2
Move the mouse pointer over the letter on the
software keyboard that you want to enter.
3
Click the letter on the software keyboard that
you want to enter.
Note
• You can move the software keyboard by dragging any
portion of the keyboard other than the keys with the mouse.
• To drag the software keyboard from the front panel, press
the arrow buttons on the keypad while holding down the
[ZOOM IN/ENTER] button.
CAUTION
• You can move the cursor with the keypad when the
software keyboard is displayed.
• [ZOOM IN/ENTER] button is enabled with a click of a
mouse when the software keyboard is displayed.
• You cannot enter 2-byte character with the VR-N900U.
Operating the Mouse Pointer from
the Front Panel for Character Entry
(without Using a Mouse)
When a mouse is not connected, you can operate the
mouse pointer from the front panel.
1
Press the [KEY] button.
• The software keyboard will appear.
• Press the [KEY] button again to close the software
keyboard.
2
Move the mouse pointer with the keypad.
Pressing the [ZOOM IN/ENTER] button is the same as
clicking at the position of the mouse pointer.