JVC DR-MV5BEK Instructions Manual page 64

Filename [MV5SEK_09Advanced Operation.fm]
MV5SEK_00.book Page 64 Wednesday, August 31, 2005 7:58 PM
ADVANCED RECORDING
64
EN
Tape Remaining Time
1
Press DISPLAY until the time remaining on the tape appears.
By pressing the DISPLAY button, you can change display to show
the clock time, counter reading or tape remaining time.
NOTE:
Depending on the type of tape being used, the tape remaining time
reading may not appear right away, or is not correct.
"– –:– –" may sometimes appear, or the display may blink on occasion.
Receiving Stereo And Bilingual Programmes
Your unit is equipped with a Digital stereo sound decoder (NICAM)
making reception of stereo and bilingual broadcasts possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
Type of Broadcast Being
Received
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
To listen to a stereo programme, press AUDIO until "HI FI L j h R"
appears on the TV screen.
To listen to a bilingual programme, press AUDIO until "HI FI L j" or
"HI FI h R" appears on the TV screen.
To listen to the standard (Regular Monaural) audio while receiving a
NICAM broadcast, press AUDIO until "NORM" appears on the TV
screen.
NOTE:
"SUPERIMPOSE" must be set to "ON", or the on-screen displays will
not appear. ( pg. 79)
To Record Stereo and Bilingual Programmes (A2)
Stereo programmes are automatically recorded in stereo on the
Hi-Fi audio track (with the normal audio track recording mixed L
and R channel sound).
Bilingual programmes are automatically recorded in bilingual on the
Hi-Fi audio track. The main soundtrack will be recorded on the
normal audio track.
To Record NICAM Stereo and Bilingual Programmes
The NICAM audio programme will be recorded on the Hi-Fi audio
track, and the standard audio programme will be recorded on the
normal audio track.
NOTES:
If the quality of stereo sound being received is poor, the broadcast
will be received in monaural with better quality.
Before playing back a programme recorded in stereo, or a bilingual
programme, refer to "Soundtrack Selection" on page 60.
Page 64Wednesday, 31 August 2005 19:58
On-screen Display
(none)
ST NICAM
BIL. NICAM
NICAM
Masterpage:Left+
B.E.S.T. Picture System
The B.E.S.T. (Biconditional Equalised Signal Tracking) system
checks the condition of the tape in use during playback and
recording, and compensates to provide the highest-possible
playback and recording pictures. You can set "B.E.S.T." to "ON" or
"OFF" to your preference. ( pg. 81)
Playback
The unit assesses the quality of the tape once you initiate
playback.
The unit adjusts the playback picture quality based on the quality of
the tape in use.
B.E.S.T. is active during automatic tracking. "BEST" appears blinking
on the front display panel.
"BEST" only appears at the beginning of automatic tracking. Even
though it doesn't appear after that, the B.E.S.T. function is operative.
Recording
The unit assesses the quality of the tape once you initiate
recording.
The unit spends approximately 7 seconds assessing the condition of
the tape, then begins recording.
ATTENTION:
Since the B.E.S.T. system works before recording actually starts,
there is a delay of approximately 7 seconds after 7 and 4 on the
remote control are pressed, or 7 on the unit is pressed. To make
sure you record the desired scene or programme in its entirety, first
perform the following steps:
A Press and hold 9 and press 7 to engage the Record Pause
mode.
The unit then automatically checks the condition of the tape and,
after approximately 7 seconds, re-enters Record Pause mode.
B Press 4 to start recording.
If you want to bypass the B.E.S.T. system and begin recording
immediately, set "B.E.S.T." to "OFF". ( pg. 81)