JVC DR-MV5BEK Instructions Manual page 45

Filename [MV5SEK_08Basic TimerDub.fm]
MV5SEK_00.book Page 45 Wednesday, August 31, 2005 7:58 PM
L-2 Select Setting
Set "L-2 SELECT" to the appropriate mode depending on the type
of appliance connected to the unit's [L-2 IN/DECODER] connector.
1
Perform steps 1 and 2 of "L-1 Output And L-1 Input Setting"
( pg. 44).
2
Press rt to select "L-2 SELECT", then press ENTER.
3
Press rt to select the
appropriate setting, then press
ENTER.
4
Press SET UP to complete the
setting.
NOTES:
If "L-2 SELECT" is set to
"S-VIDEO/RGB", it is not possible
to output colour signals correctly
from the VHS deck.
If "L-2 SELECT" is set to "DECODER", only the DVD deck operates
properly.
* The boldface settings below indicate the settings at your purchase.
8 L-2 SELECT — VIDEO/RGB / S-VIDEO/RGB /
SAT VIDEO/RGB / DECODER
Select "VIDEO/RGB" or "S-VIDEO/RGB" to use this unit as the
recording deck with the player connected to the [L-2 IN/
DECODER] connector, or to use the satellite receiver connected to
the [L-2 IN/DECODER] connector.
VIDEO/RGB
: If a connected appliance's output is compatible with
regular video signals, set to "VIDEO/RGB".
S-VIDEO/RGB
: If a connected appliance's output is compatible with
Y/C signals, set to "S-VIDEO/RGB". You can obtain high-quality
picture. (For connection, be sure to use a 21-pin SCART cable
that is compatible with the Y/C signal.)
Select "SAT VIDEO/RGB" to view a satellite programme with the
TV set while the unit is turned off. (
SAT VIDEO/RGB
: If a connected satellite receiver's output is
compatible with regular video signals, set to "SAT VIDEO/RGB".
DECODER
*: To use a decoder connected to the [L-2 IN/DECODER]
connector.
* This setting is not available in the U.K.
NOTES:
If you have a satellite receiver or a decoder connected to the [L-2 IN/
DECODER] connector, be sure to set "L-2 SELECT" back to
appropriate mode after editing.
If you are not connecting a satellite receiver or a decoder to the [L-2
IN/DECODER] connector, leave "L-2 SELECT" set to "VIDEO/RGB".
When "L-2 SELECT" is set to "SAT VIDEO/RGB", "SAT" appears on
the TV screen or front display panel instead of "L-2".
If "L-1 OUTPUT" is set to "SCART S-VIDEO", it is not possible to set
"L-2 SELECT" to "DECODER" or "SAT VIDEO/RGB".
If "L-1 OUTPUT" is set to "SCART RGB", it is not possible to set "L-2
SELECT" to "DECODER".
If "L-1 OUTPUT" is set to "COMPONENT" and "L-2 SELECT" to "SAT
VIDEO/RGB" or "DECODER", be sure to connect the [L-1 IN/OUT]
connector with a TV.
If "L-2 SELECT" is set to "S-VIDEO/RGB", the monocrome signal is
output from VHS deck. Be sure to select setting other than
"S-VIDEO/RGB" when you use the VHS deck.
Page 45Wednesday, 31 August 2005 19:58
DVD SET UP FUNCTION SET UP INITIAL SET UP
VIDEO IN/OUT RECORDING SET DISPLAY SET OTHERS
MONITOR TYPE 4:3LB
F-1 INPUT VIDEO
L-1 INPUT VIDEO
L-1 OUTPUT SCART VIDEO
VIDEO/RGB
L-2 SELECT S-VIDEO/RGB
S-VIDEO/RGB
SAT VIDEO/RGB
SET UP OK
SELECT WITH [CURSORS]
DECODER
THEN PRESS [ENTER]
EXIT SELECT
pg. 76)
Masterpage:Right+
F-1 Input Setting
Set "F-1 INPUT" to the appropriate mode depending on the
connector ([VIDEO] or [S-VIDEO]) being used on the front panel.
1
Perform steps 1 and 2 of "L-1 Output And L-1 Input Setting"
( pg. 44).
2
Press rt to select "F-1 INPUT", then press ENTER.
3
Press rt to select the
appropriate setting, then press
ENTER.
4
Press SET UP to complete the
setting.
* The boldface settings below
indicate the settings at your
purchase.
8 F-1 INPUT — VIDEO / S-VIDEO
VIDEO
: When connecting an appliance to the [VIDEO] input
connector, set to "VIDEO".
S-VIDEO
: When connecting an appliance to the [S-VIDEO] input
connector, set to "S-VIDEO".
NOTE:
If "F-1 INPUT" is set to "S-VIDEO", the monocrome signal is output
from VHS deck. Be sure to select "VIDEO" when you use the VHS
deck.
EDITING
45
EN
DVD SET UP FUNCTION SET UP INITIAL SET UP
VIDEO IN/OUT RECORDING SET DISPLAY SET OTHERS
MONITOR TYPE 4:3LB
F-1 INPUT VIDEO
VIDEO
L-1 INPUT VIDEO
S-VIDEO
L-1 OUTPUT SCART VIDEO
L-2 SELECT VIDEO/RGB
SET UP OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
EXIT SELECT