JVC DR-MV5BEK Instructions Manual page 41

Filename [MV5SEK_08Basic TimerDub.fm]
MV5SEK_00.book Page 41 Wednesday, August 31, 2005 7:58 PM
DV Dubbing (DVD Deck Only)
You can dub programmes from a camcorder or DV equipment
connected to the unit with a DV cable. The unit's remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
NOTES:
Be sure to use the DV cable VC-VDV 204U for connection.
When you connect a PC to the [DV IN] connector, we do not
assure the normal operation of this unit.
Your unit
VHS
STANDBY/ON
S-VIDEO VIDEO AUDIO
Camcorder
DV equipment
Page 41Wednesday, 31 August 2005 19:58
DVD REC
PR
VHS/DVD
VHS DUBBING DVD
DV IN
To [DV IN]
DV cable
(VC-VDV 204U)
(not provided)
DV connector
Masterpage:Right+
1
Connect a camcorder or DV equipment to the [DV IN] connector
on the unit's front panel.
2
Load a DVD-RAM/RW/R disc on the unit.
3
Press PR +/– to set the channel to "DV".
The "DV DUBBING" controller appears on the TV screen.
If " " does not appear on the "DV DUBBING" controller, make
sure the DV equipment is connected correctly.
4
Press w e to select
5
Press rt to select the desired
sound track, then press ENTER.
AUDIO 1
: Select this to record the
original stereo sound played
back on the connected DV
equipment.
AUDIO 2
: Select this to record the
dubbed stereo sound played
back on the connected DV
equipment.
MIX
: Select this to record the sound of both "AUDIO 1" and
"AUDIO 2".
Note that this selection is not available when the source programme
is recorded in 16BIT (48 kHz) mode.
6
Press REC MODE repeatedly to set the recording mode.
7
Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9.
To play back in slow speed (1/10 of the normal speed), press 9 to
pause playback, then press 3 or 5.
To play back frame-by-frame, press 9 to pause playback, then press
9 repeatedly. Each press of 9 advances a frame.
To change the playback direction, press 3 or 5.
8
Press w e to select
dubbing starts.
Playback on the external DV equipment and recording on the unit
should start simultaneously.
When the playback from the beginning is not possible, the "DV
DUBBING" controller cannot be used. Perform dubbing without using
the "DV DUBBING" controller. (
To pause dubbing, press w e to select
ENTER. Both the unit and the external DV equipment pause dubbing.
Pressing 9 on the unit also works the same way.
To clear the "DV DUBBING" controller from the TV screen, press
ON SCREEN.
9
Press 8 on the remote control to stop dubbing.
Both the unit and the external DV equipment stop dubbing.
NOTES:
Dubbing copyright guarded programmes is not possible.
Original DV informations such as the recording date and time are not
recorded.
The superimposed indication during the operation or dubbing is not
recorded.
It is not possible to perform dubbing when "]" lights up on the unit.
Press VHS] so that "]" lights off.
Performing dubbing without using the "DV DUBBING"
controller
A Press PR +/– to set the channel to "DV".
B Press REC MODE repeatedly to set the recording mode.
C Start playback on the external DV equipment slightly before the
actual point from where you wish to start dubbing.
D Press 7 on the unit to start recording. Or press and hold 7 and
press 4 on the remote control. The dubbing starts.
E When the dubbing ends, press 8 on the unit, then stop
playback on the external DV equipment.
EDITING
41
EN
, then press ENTER.
, then press ENTER. The
below)
, then press