Advertisement
Available languages
Available languages
Grill Lighting
Instructions
1. Before each use, check all hoses for cracks, nicks, cuts,
burns or abrasions. If a hose is damaged in any way, do
not use your grill before replacing the hose with an
authorized part from the Parts List. Also make sure all
gas supply connections
are securely tightened.
2.
Familiarize yourself with the safety and Use and Care
instructions
in this guide. Do not smoke while lighting
grill or checking
gas supply connections.
3.
Be sure the LP Gas tank is filled.
4.
Open the Grill Lid.
Failure to replace
a faulty hose, secure
gas supply
connections
or to open the Lid before proceeding
to the Lighting
Procedures
could result in a fire
or explosion
that could
cause
serious bodily injury,
death, or property
damage.
5. Set Control Knobs to OFF and open the LP Gas tank
valve SLOWLY 1/4 of a turn.
m
open
LP Gas tank
OFF
\\\
6. Push and turn Burner Control Knob to _r and you will hear
a
clicking sound as the burner is being ignited. Once the
burner
is lit, turn the knob back to Hi.
I
Low
i
i
OFF
7. If ignition does not occur in 5 seconds, turn gas off at
source and turn Control Knobs OFF. Wait at least 5
minutes for gas to clear, then retry.
If your grill still fails
to light turn the burner Control Knob(s) and gas source
OFF and conduct a leak test of ALL gas connections
and gas sources as explained in the LP Gas Tank
Installation of this guide. If no leaks are detected, wait
5 minutes for any gas to clear and repeat the lighting
procedure.
8. After one Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn.
9. Turn Knob for each other burner and light as you move
toward the fuel source.
Burner Control Knobs on Control Panel
Grill
Main Burner
Rotisserie Infrared
Burner
Burner
19
Rotisserie
Burner
Lighting
Instructions
1. Follow steps 1 through 5 of the Grill Lighting
Instructions.
2. Push and turn Burner Control Knob to _€ and hold
knob in.
3. Keep pressing while you turn knob to Hi and hold in
5 - 10 seconds before releasing.
4. If ignition does not occur in 5 seconds, turn gas off
at source and turn Control Knobs OFF. Wait at least
5 minutes for gas to clear, then retry. If your grill still
fails to light turn the Control Knob(s) and gas
source OFF and conduct a leak test as explained in
the LP Gas Tank Installation of this guide. If no
leaks are detected, wait 5 minutes for any gas to
clear and repeat the lighting procedure.
5. After Burner is lit, turn the tank valve SLOWLY one
more 1/4.
IMPORTANT:
Do not use the Rotisserie Burner and Main
Burners at the same time. Rotisserie burner is for Rotis-
serie Cooking only.
ROTISSERIE
INFRAREDBURNER
BURNER KNOB:
KNOB:
!
!
Hi
OFF
OFF
GRIDDLE BURNER
KNOB:
OFF
Infrared
Burner
Lighting
Instructions
1. Follow steps 1 through 5 of the Grill Lighting
Instructions.
2. Push and turn Burner Control Knob to _€and hold
knob in.
3. Keep pressing while you turn knob to Hi and hold in
5 - 10 seconds before releasing.
4. If ignition does not occur in 5 seconds, turn gas off
at source and turn Control Knobs OFF. Wait at least
5 minutes for gas to clear, then retry. If your grill still
fails to light turn the Control Knob(s) and gas
source OFF and conduct a leak test as explained in
the LP Gas Tank Installation of this guide. If no
leaks are detected, wait 5 minutes for any gas to
clear and repeat the lighting procedure.
5. After Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn.
Griddle
Burner
Lighting
Instructions
1.
Follow steps 1 through 3 of the Grill Lighting
Instructions.
2.
Open the Griddle Side Burner Lid.
3.
Set Control Knobs to OFF and open the LP Gas
tank valve SLOWLY 1/4 of a turn.
4.
Push and turn Burner Control Knob to _ and you
will hear a clicking sound as the burner is being
ignited. Once the burner is lit, tum the knob back to Hi.
5.
If ignition does not occur in 5 seconds, turn gas off
at source and turn Control Knobs OFF. Wait at least
5 minutes for gas to clear, then retry.
If your grill still
fails to light turn the Control Knob(s) and gas
source OFF and conduct a leak test as explained in
the LP Gas Tank Installation of this guide. If no
leaks are detected, wait 5 minutes for any gas to
clear and repeat the lighting procedure.
6.
After Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn.
Advertisement
