Sign In
Upload
Download
Table of Contents
Contents
Add to my manuals
Delete from my manuals
Share
URL of this page:
HTML Link:
Bookmark this page
Add
Manual will be automatically added to "My Manuals"
Print this page
×
Bookmark added
×
Added to my manuals
Manuals
Brands
Will Burt Manuals
Work Light
Night Scan Chief
Installation, operation & maintenance manual
Will Burt Night Scan Chief Installation, Operation & Maintenance Manual page 41
Transportable lighting system
Hide thumbs
1
2
3
4
Table Of Contents
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
page
of
65
Go
/
65
Contents
Table of Contents
Troubleshooting
Bookmarks
Table of Contents
Advertisement
Err 1,07
Err 1,08
Err 1,09
Err 1,10
Err 1,11
Err 1,12
Revision 1
Unrecoverable
The Base board has
Communication
not sent out
Error
communications
recently
Software Fault
Internally detected
error
Initiate
The Initiate input has
Pushbutton
been closed for too
long.
EEPROM Life
More than 20,000
writes have been
made to a particular
EPROM location
Saddle Location
The internal linear
actuator limit switch
has opened before
preload occurred
Actuator 90 °
The proximity switch
sensing the mast
Proximity Switch
actuator at 90 ° has
Disagreement
conflicting
complementary
outputs.
Night Scan Chief
mast path, and
confirm that the
proximity switch is
being properly
activated.
Indicates a software
problem. Notify Will-
Burt
Indicates a software
problem. Notify Will-
Burt
Wiring Short in the
DC cable or
incorrect DIP switch
setting (S2)
Will only occur when
the mast has had in
excess of 20,000
cycles which is
unlikely to happen.
Replace the base
board.
The saddle is too
low with respect to
the Chief base. Shim
the saddle up as
needed. Refer to
section 2.4 for
flatness
requirement.
There may be a
wiring problem, or a
defective proximity
switch. Check the
voltages at J3 pins 1
and 3 with respect to
pin 2. These two
voltages should be
opposite of each
other as the
proximity switch is
activated and
inactivated. The
voltages should be
close to battery
voltage or close to
ground. If they are
not, replace the
actuator 90 °
proximity switch.
Refer to system
4-11
Table of
Contents
Previous
Page
Next
Page
1
...
38
39
40
41
42
43
44
45
Show Quick Links
Quick Links:
System Schematics
Troubleshooting Electrical
Table 4-4. List of Warning Codes
Hide quick links:
Permanently
Temporary
Cancel
Advertisement
Table of Contents
Troubleshooting
Troubleshooting Electrical
40
Troubleshooting Mechanical
49
Related Products for Will Burt Night Scan Chief
Will-Burt NIGHT SCAN
Will Burt Nightscan Spot
Will Burt Night Scan Chief Series
Will Burt NIGHT SCAN LITE
Will Burt NIGHT SCAN VERTICAL
Will Burt Night Scan Vertical Complete
Will Burt Night Scan Vertical Heavy Duty Towing
Will Burt Night Scan Vertical HDT
Will Burt Night Scan Powerlite
Will Burt Night Scan Powerlite Xtreme
Will Burt Night Scan Powerlite Heavy Duty Towing
Will Burt Night Scan Powerlite HDT
Will Burt Night Scan Powerlite 2.3
Will Burt Night Scan Powerlite 4.5
Will Burt Night Scan Powerlite Xtreme 6.0
Will Burt Night Scan Powerlite Xtreme 7.5
Table of Contents
Print
Rename the bookmark
Delete bookmark?
Delete from my manuals?
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL