Related Manuals for Spirit SPT0034- XE195
Summary of Contents for Spirit SPT0034- XE195
- Page 1 XE195 ELLIPTICAL SPT0034 OWNER’S MANUAL PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW ELLIPTICAL!
-
Page 2: Table Of Contents
TABLE OF CONTENTS Important Safety Instructions Important Electrical Instructions Important Operation Instructions Assembly Instructions Features Console Operation Programmable Features General Maintenance Exploded View Diagram/Parts List Manufacturer’s Limited Warranty... - Page 3 Congratulations on your new elliptical and welcome to the Spirit family! Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available.
-
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING - Read all instructions before using this appliance. DANGER - To reduce the risk of electric shock disconnect your Spirit elliptical from the electrical outlet prior to cleaning and/or service work. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the elliptical on a flat level surface with access to a 230-volt, 10-amp grounded outlet with only... -
Page 5: Important Electrical Instructions
IMPORTANT ELECTRICAL INSTRUCTIONS WARNING! NEVER remove any cover without first disconnecting AC power. lf voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for proper testing. -
Page 6: Assembly Instructions
ASSEMBLY INSTRUCTIONS PRE-ASSEMBLY Using a razor knife (Box Cutter), cut the banding straps that wraparound the carton, then cut around the dotted line at the bottom of the box; lift the box over the unit and unpack. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. - Page 7 CONSOLE MAST ASSEMBLY Locate the Console Mast (12) and Console Mast Cover (41) and slide the Cover onto the Mast as far as it will go. Make sure the Console Mast Cover (41) is facing the correct way. At the top opening of the Main Frame (1), there is a Computer Cable (31) tied to a twist tie wire. Feed the twist tie wire and Computer Cable (31) into the bottom of the Console Mast (12) and out of the opening at the top.
-
Page 8: Swing Arm Assembly
SWING ARM ASSEMBLY Slide two Wave Washers (83) onto both the Left and Right Console Mast axle. Slide the Swing Arms (L) and (R), (10ƒ& 11) onto the appropriate side of the axle. Note: Make sure the arms are attached as shown in the illustration. Place a Flat Washer (79) onto each Hex Head Bolt (59) and fasten in the end of the left and right axle. -
Page 9: Connecting Arm Assembly
CONNECTING ARM ASSEMBLY Untie the twist tie that holds each bushing (22) to the Connecting Arm end. Align the hole in the end of the Connecting Arms (L & R) (8 & 9) with the hole in the bracket of the Swing Arms (L) and (R), (10 & 11). - Page 10 PLASTIC PARTS ASSEMBLY Mate the Connecting Arm Covers (57 & 58) on the joint where the Connecting Arms (8, 9) are joined to the Swing Arms (10, 11). Fasten together with two Phillips Head Screws (105) and one Sheet Metal Screws (87) on each joint. Tighten with the Short Phillips Head Screw Driver (107).
-
Page 11: Features
FEATURES FOOTPADS Through research performed with a leading sports scientist and physical rehabilitation expert, Spirit engineering has developed a breakthrough in pedal design. No other elliptical, at any price, offers these unique features. The history of elliptical use over the past few years tells us that many users suffer from numb toes while working out on elliptical trainers. -
Page 12: Console Operation
OPERATION OF YOUR CONSOLE GETTING FAMILIAR WITH THE CONTROL PANEL POWER UP When the A.C. power cord is connected to the Elliptical, the console will automatically power up. If there is no input to the console for 20 minutes the console will go to stand-by mode. In stand-by mode the console display will turn off. -
Page 13: Quick Start
QUICK START This is the quickest way to start a workout. After the console powers up you just press the Start key to begin, this will initiate the Quick Start mode. In Quick Start the Time will count up from zero and the workload may be adjusted manually by pressing the Level Up or Down buttons. - Page 14 PROGRAM KEYS The Program Keys are used to preview each program. When you first turn the console on you may press each program key to preview what the program profile looks like. If you decide that you want to try a program, press the corresponding program key and then press the Enter key to select the program and enter into the data-setting mode.
-
Page 15: Programmable Features
PROGRAMMABLE FEATURES MANUAL The Manual program works as the name implies, manually. This means that you control the workload and not the computer. To start the Manual program, follow the instructions below or just press the Manual button, then the Enter button and follow the directions in the Message Center. -
Page 16: Preset Programs
PRESET PROGRAMS The bike has five different programs that have been designed for a variety of workouts. These five programs have factory preset work level profiles for achieving different goals. Hill RESISTANCE This program follows a triangle or pyramid type of gradual progression from approximately 10% of maximum effort (the level that you chose before starting this program) up to a maximum effort which lasts for 10% of the total workout time, then a gradual regression of resistance back to approximately 10% of... - Page 17 PROGRAMMING PRESET PROGRAMS Select the desired program button then press the Enter key. The Message Center will ask you to enter your Age. You may adjust the age setting, using the Level Up and Down keys, then press the Enter key to accept the new number and proceed on to the next screen.
- Page 18 RATE OF PERCEIVED EXERTION Heart rate is important but listening to your body also has a lot of advantages. There are more variables involved in how hard you should workout than just heart rate. Your stress level, physical health, emotional health, temperature, humidity, the time of day, the last time you ate and what you ate, all contribute to the intensity at which you should workout.
-
Page 19: General Maintenance
GENERAL MAINTENANCE Wipe down all areas in the sweat path with a damp cloth after each workout. If a squeak, thump, clicking or rough feeling develops the main cause is most likely one of two reasons: i. The hardware was not sufficiently tightened during assembly. All bolts that were installed during assembly need to be tightened as much as possible. -
Page 20: Exploded View Diagram/Parts List
EXPLODED VIEW DIAGRAM... -
Page 21: Parts List
PARTS LIST Dwg # Part description Main Frame Rear Rail Assembly Console Holder Assembly Cross Bar Bushing Housing, Pedal Arm Pedal Arm (L) Pedal Arm (R) Connecting Arm (L) Connecting Arm (R) Swing Arm (L) Swing Arm (R) Console Mast Idler Wheel Assembly Crank Axle Bushing... - Page 22 Dwg # Part description Gear Motor 300m/m_Sensor W/Cable Sensor Rack 850m/m_Handpulse W/Cable Assembly 36~4 Ø3 × 20m/m_Tapping Screw Power Adaptor Transportation Wheel Slide Wheel , Urethane 40~1 3/8" × 2"_Flat Head Socket Bolt Rubber Foot 40~2 Console Mast Cover Side Case (L) Side Case (R) Round Disk Round Disk Cover...
- Page 23 Dwg # Part description 5/16" × 23 × 1.5T_Flat Washer 5/16" × 20 × 1.5T_Flat Washer Ø25.5 × 33.5 × 1.5T_Nylon Wave Washer M8 × 170m/m_J Bolt Ø17_Wave Washer 3/8" × 23 × 1.5T_Curved Washer 5 × 16m/m_Tapping Screw 4 × 19m/m_Sheet Metal Screw Ø3.5 ×...
-
Page 24: Manufacturer's Limited Warranty
Dwg # Part description M8 × 6.3T_Nut Axle Stopper M5 × 5m/m_Slotted Set Screws Adaptor Power Cord... - Page 25 WARRANTY, SAFETY AND ASSEMBLY INFORMATION SPT0034- XE195 IMPORTANT Please read and retain this manual as it will assist with identification for parts and service. --------------------------------------------------------------------------------------------------------------------------- BOYLES FITNESS warrants their Elliptical to be free from defects in material and workmanship under normal use and service conditions.
-
Page 26: Warranty Information
WARRANTY INFORMATION SPT0034 Congratulations on your purchase! As of January 1 2012, new legislation under the Australian Consumer Law requires certain information to be included in any product warranty issued in Australia. This warranty compliments the warranty found in the manual and has been developed in line with the Australian Consumer Law. - Page 27 processing of your enquiry please have proof of purchase, the date of purchase and the retailer name you purchased the item from, and the brand on the product. Photos of the product, and scans of receipts, may be requested to assist with your claim. The service centre representative will assess the claim.
Need help?
Do you have a question about the SPT0034- XE195 and is the answer not in the manual?
Questions and answers