The following list of tools and supplies are required for the
completion of this installation:
Tools (not provided)
•
Slip Joint Pliers 12"
•
Pipe Wrench 12"
•
Adjustable Wrenches
•
Torpedo Level
•
Fine Slot Drivers
•
Phillips Drivers: #0, 1
•
Nut Drivers: 5/16, 3/8
Supplies Required (not provided)
•
Copper Pipe
•
Ground Wire
•
Flux and Flux Brush
•
Solder (lead free)
•
Assorted Copper
fittings
•
Plumber Tape or Pipe
Dope (for potable
water)
•
3 Water Shut-off Valves
(same size as install
piping)
•
Unscented Chlorine
Bleach (Clorox) - 5-6%
or 12%
Tools Supplied with Integrity Test Kit
•
Integrity Tester
•
Cap Wrench
•
Silicone Lubricant -
DOW CORNINg 111
•
Two 1/4" Tubings
Spare Parts (recommended)
•
AA Batteries
•
Inlet Solenoid Valve
•
Air Relief Valve
•
Stainless Steel Flex
Hose
•
3/4" Inlet/Outlet Fitting
WARNING:
recommended for use as the bypass, inlet and outlet
valves. Gate valves have a tendency to leak, allowing
unfiltered water to mix with filtered water. The result
may cause personal injury, sickness and/or death.
•
Knife
•
Air Pump
•
1/4" Hex Key
•
Torch with Gas
•
Snips
•
Robertson Drivers:#1, 2
•
Masonry Drill with 3/8"
Bit
•
Pen or Pencil
•
Funnel
•
Hose Clamps
•
Suspension Strap
•
Tie Wraps or Cable Ties
•
5/8" Hose for Drain
(comply with local
plumbing code)
•
2' x 2' Patio Stones
(required only for
heated floor)
•
Housing Wrench
•
Two Pressure Gauges
•
Digital Air Pressure
gauge
•
O-ring
•
Drain Solenoid Valve
•
Advanced Plus
Controller
•
1/4" Mini Ball Valve
with Plug
•
1/2" Nipple
Ball valves are
System Parts List
UFC 211 and UF 211
•
System
(pre-assembled)
•
System Base
•
Carbon Prefilter
•
Two Stainless Steel Flex Hoses
Inside the bubble bag:
•
1 - Drain Solenoid Valve
(normally closed)
•
1 - Nylon Elbow
•
2 - 1/4" Mini Ball Valves
with Plugs
•
1 - Air Relief Valve
•
3 - 3/8" Bolts
Surface Water Kit (optional)
•
1 - External Prefilter
Housing
•
1 - Wall Bracket Kit
•
Mounting Screws
•
1 - Inlet Solenoid Valve
(normally open)
Horizontal Mounting Kit (optional)
•
2 - Cast Iron Stands
•
1 - Metal Support Strap •
•
1 - Brass 1/2" Elbow
•
1 - Brass 1/2" Plug
•
1 - PVC 1/2" Nipple at
2" Long
•
1 - Polypropylene 1/4"
Closed Nipple
•
1 - Concrete Floor Bolt
•
3 - 1/4" x 1" Bolt & Lock
Nut
•
Transformer (120VAC)
•
Advanced Plus
Controller
•
Cap Wrench
•
2 - 3/4" Inlet/Outlet
fittings
•
1 - 1/2" Nipple
•
3 - 1/4" x 2-1/2"
Anchors
•
3 - Shims
•
1 - 1/4" Mini Ball Valve
with Plug
•
1 - Check Valve
•
4 - 1/2" Lag Bolts
•
1 - External Prefilter
Cartridge (20- micron
nominal)
•
1 - Air Relief Valve
2 - Cast Iron Cross
Members
•
1 - Brass 1/4" Tee
•
1 - foam gasket
•
1 - Brass 1/2" x 1/4"
Reducer Elbow
•
1 - Polypropylene 1/2"
Closed Nipple
•
4 - Wall Mounting Bolts
2-1/2" Long
•
5 - 5/16" x 1-1/4" Bolt &
lock Nut
23