Fm And Dab Antenna Installation; Connecting For Nuvonet Use; Ir Control Of The T2Dab - Nuvo NV-T2DAB Installation Manual

FM and DAB Antenna Installation (Fig. 4)
The T2DAB is not shipped with an FM or DAB antenna. Any
after-market FM or DAB antenna will supply a signal. The
connection for both antennas is done with standard 75 ohm
RG6 coaxial cable. A separate "F" connector for both signal
inputs are provided on the T2DAB back panel.
Note, that signal quality is greatly affected by the location and
quality of the attached antennas. Often, best reception is
achieved by placing the antennas as high as possible.
Connecting for NuVoNet Use (Fig. 5)
Once audio outputs A and B are set for NuVoNet, the T2DAB is
ready to communicate in real time with the Grand Concerto or
Essentia E6G audio distribution systems. To complete the
connection, all that is necessary is a single CAT5 cable from the
NuVoNet output on the T2DAB's back panel to one of the Device
inputs on either the Grand Concerto EZ Port or the Essentia E6G
Allport. Since the outputs of the Tuner must be set as a specific
source number input for NuVoNet communication, the number
of the Device connection used is irrelevant to the system's
operation. Once the connection is complete, the tuner is ready
to fully communicate with NuVoNet.
IR Control of the T2DAB (Fig. 6)
The T2DAB can be used without NuVoNet as a standalone dual
tuner. The IR receiver is always active, however control through
IR is typically done in Standalone mode,(see section I. Setting
the Audio Outputs for NuVoNet or Standalone use, pg. 7).
Once the audio outputs are set at Standalone, the T2DAB offers
three methods for IR control. One is to take the IR output of
your control device using a mono 3.5mm patch cable into the
Direct IR input on the back panel of the T2DAB. Tuners A and B
feature discrete commands, allowing both tuners to be
controlled independently from one input. The second method
for IR control is to attach an IR emitter over the IR receiver on
the front panel, and the third method is to aim the remote
control at the IR receiver located on the front panel.
Fig. 4
Fig. 5
IR INPUT NuVoNet RS 232
SYSTEM
Fig. 6
IR INPUT NuVoNet RS 232
SYS TE M
VARIABLE
SPEAKER
OUTPUT
40W/6 OHMS X 2
40W/6 OHMS X 2
TIP=L
LEFT RIGHT LEFT
RING=R
FIXED
OUTPUT
ZONE 5
1 2 3 4
5 6 7 8
ZONE TRIGGER OUTPUTS
8
AUDIO AUDIO
L R L R
TUNER A TUNER B
SIR 3:09 PM
SR 86 (P101)
SIRIUS Pops
Jozef Kossovit
Hungaria
MENU
OK
07 28
Model NV-T2DAB
Du al AM/ FM Tune r
Nu Vo Techn ol og ie s LL C He br on , KY USA
•
ww w.nu vo te ch no lo gi es .c om
RoHS
CM
CO NF OR MS TO UL
ST D. 60 06 5 CE RT IF IE D
TO CAN /C SA ST D.
3033118
C2 2. 2 No .6 00 65 :0 6
Model NV -T2 DAB
Dual SIRI US Ready AM/FM Tuner
NuVo Techno log ies LLC Hebr on, KY USA •
www.nuvot echno logi es. com
RoHS
CM
CONFORMS TO UL
STD.60 065 CERTIFIED
TO CAN/CSA STD.
3033118
C22.2 No.60 065:0 6
VARIABLE VAR.
SPEAKER OUTPUT SPEAKER OUT
40W/6 OHMS X 2 RS 232
TIP=L
RIGHT
LEFT RIGHT
RING=R
FIXED FIX.
OUTPUT OUT
ZONE 6 ZONE 7 ZONE 8 PROGRAM
1 2 3 SUM1 SYS ON
CONNECT TO CONNECT TO
NV-I8EZP1 NV-I8X
120V
USE NV-NC1 USE NV-SLC1 NuVo Technologies Cincinnati Ohio USA
CABLE CABLE
4 5 6 SUM2
EXT. MUTE
C
EMITTER OUTPUTS SYSTEM
NETWORK DIGITAL LINK
0728
USE CNLY WITH 250V FUSE
MODEL NV-I8M
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
60Hz 500W FUSE:T5 A
www.nuvotechnologies.com
CONFORMS TO
R
UL STD.6500
US CERTIFIED TO
3033118 CAN/CSA STD.E60065