7Hohphwu - FUTABA 14SG Instruction Manual

TELEMETRY
This screen displays your choice of data from the
receiver.
Also warnings can be activated regarding
other data from your aircraft. For example, if the
receiver voltage drops, the user can be warned by
an alarm (and vibration).
[TELEMETRY] FDQ EH FDOOHG LI WKH HOME/EXIT EXWWRQ
LV SXVKHG IURP D home screen
6HOHFW >7(/(0(75<@ LQ WKH /LQNDJH PHQX DQG
DFFHVV WKH VHWXS VFUHHQ VKRZQ EHORZ E\ WRXFKLQJ
WKH 571 EXWWRQ
6HOHFW WKH IXQFWLRQ QDPH
DQG UHWXUQ WR WKH /LQNDJH
PHQX E\ WRXFKLQJ WKH
R T N E X W W R Q  2 U W K H
H O M E / E X I T E X W W R Q L V
SXVKHG
How to see telemetry date
 7HOHPHWU\ VFUHHQ FDQ EH FDOOHG LI WKH +20(
(;,7 EXWWRQ LV SXVKHG IURP WKH KRPH VFUHHQ
2U VHOHFW >7(/(0(75<@ LQ WKH /LQNDJH PHQX
DQG DFFHVV WKH VHWXS VFUHHQ E\ WRXFKLQJ
WKH 571 EXWWRQ
 ,I HDFK LWHP LV FKRVHQ DQG WKH 571 EXWWRQ LV
SXVKHG DQ DODUP VHWXS FDQ EH SHUIRUPHG
Z L W K W K H P L Q L P X P  P D [ L P X P D I W H U D
WUDQVPLWWHU LV WXUQHG RQ
*Receiver voltage can be checked immediately. An optional
sensor will need to be attached to S.BUS2 of a receiver if
you would like to see other information.
*No special setup is necessary if each sensor displayed
is left as in the default setup. Separate sensor ID
is also unnecessary. However, if two or more of
one kind of sensor is used, setup is required in the
"SENSOR" menu.
'LVSOD\LQJ GDWD IURP WKH UHFHLYHU
3XVK S1 EXWWRQ WR DGYDQFH WR QH[W SDJH
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest14CH mode can use all the telemetry functions.
5HFHLYHU ! 7UDQVPLWWHU 7KH
UHFHSWLRQ VWUHQJWK LV VKRZQ
<SensorTouch™>
:DUQLQJ
Do not watch the transmitter screen during
ÀLJKW
<RX PD\ ORRVH VLJKW RI WKH DLUFUDIW GXULQJ ÀLJKW DQG WKLV LV
extremely dangerous. Have an assistant on hand to check
the screen for you. A pilot should NEVER take his eyes off
his aircraft.
<Functions of Linkage Menu>
6FUROOLQJ
0RYLQJ FXUVRU
6HOHFWLQJ PRGH
$GMXVWLQJ YDOXH
7R QH[W SDJH
91