Table of Contents
Advertisement
6:$6+
Neutral Point
At your linkages, if the servo horn deviates from
a perpendicular position at neutral, the linkage
compensation functions in this menu may not
compensate effectively. To correct this use the
Neutral Point function. This will move the neutral
point of the servos to the actual perpendicular
position. However, this adjustment changes only
the axis point of the compensation functions in this
menu, and does not affect the neutral position of
other functions.
Swash AFR
Swash AFR function reduces, increases, or
reverses the rate (travel) of the aileron, elevator and
collective pitch functions, by adjusting or reversing
the motion of all servos involved in that function,
only when using that function.
Mixing Rate
This mixing is used to compensate the swash-
plate as necessary during specific control inputs.
6HOHFW >6:$6+@ LQ WKH /LQNDJH PHQX DQG DFFHVV
WKH VHWXS VFUHHQ VKRZQ EHORZ E\ WRXFKLQJ WKH
571 EXWWRQ
6HOHFW WKH IXQFWLRQ QDPH
DQG UHWXUQ WR WKH /LQNDJH
PHQX E\ WRXFKLQJ WKH
R T N E X W W R Q
2 U W K H
H O M E / E X I T E X W W R Q L V
SXVKHG
Neutral point setting procedure
The neutral point becomes the correction
standard point.
*Adjusting the servo horn so that the neutral point is near the
50% position makes the mixing amount small.
1HXWUDO SRLQW VHWWLQJ
0RYH WKH FXUVRU WR WKH >326@ LWHP DQG KROG
WKH SLWFK RSHUDWLRQ VR WKDW WKH VHUYR KRUQ LV
DW D ULJKW DQJOH WR WKH OLQNDJH URG DQG 7RXFK
WKH 571 EXWWRQ IRU RQH VHFRQG 7KLV YDOXH
LQGLFDWHV WKH VHUYR
V QHXWUDO SRVLWLRQ
$IWHU UHDGLQJ WKH QHXWUDO SRLQW XVH WKH
RWKHU FRUUHFWLRQ IXQFWLRQV WR PDNH IXUWKHU
DGMXVWPHQWV
86
<Functions of Linkage Menu>
6ZDVK $)5 DQG OLQNDJH FRUUHFWLRQ IXQFWLRQ KHOLFRSWHU RQO\ H[FHSW
VZDVK W\SH +
The following compensation mixing is possible;
PIT to AIL, PIT to ELE, AIL to PIT, ELE to AIL,
and ELE to PIT (HR3 mode.) It adjusts the swash-
plate to for proper operation of each control using
the corresponding compensation mixing.
Linkage Compensation
swash-plate for pitch control at low pitch and high
pitch.
Speed Compensation
is generated by the difference in the movements of
each servo when the swash-plate moves.
Subtrim
during swash setting.
Pitch adjustment function
used while adjusting the pitch.
Swash AFR setting procedure
WKDW WKH VHUYRV WUDYHO WKH VSHFL¿HG DPRXQW E\ >$,/@
[ELE], and [PIT] operation.
0RYH WKH FXUVRU WR WKH IXQFWLRQ \RX ZDQW WR
$GMXVW WKH $)5 UDWH E\ VFUROOLQJ WKH WRXFK
This compensation mixing is used to correct the
This function is used to cancel the reaction that
Subtrim for aileron, elevator and pitch can be set
+LJK QHXWUDO DQG ORZ SLWFK ¿[HG RXWSXWV FDQ EH
<SensorTouch™>
The swash AFR function makes adjustments so
DGMXVW DQG WRXFK WKH 571 EXWWRQ WR VZLWFK WR
WKH GDWD LQSXW PRGH
VHQVRU
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
*When the RTN button is touched for one second, the AFR
rate is reset to the initial value.
7RXFK WKH 571 EXWWRQ WR HQG DGMXVWPHQW DQG
UHWXUQ WR WKH FXUVRU PRGH
6FUROOLQJ
0RYLQJ FXUVRU
6HOHFWLQJ PRGH
$GMXVWLQJ YDOXH
7R QH[W SDJH
Advertisement
Table of Contents
