Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Paramount Fitness PFT-200
Summary of Contents for Paramount Fitness PFT-200
- Page 1 PFT-200 UNCTIONAL RAINER SSEMBLY ANUAL AM-PFT-200A...
- Page 2 ESSAGE TO USTOMERS Thank you for purchasing the Paramount PFT-200 Functional Trainer. Because of the many unique features included in this product, this manual was created to provide you with information on how to properly assemble and maintain your equipment. Proper maintenance will ensure that your new equipment will last for years.
-
Page 3: Table Of Contents
ABLE OF ONTENTS ............................4 AFETY ....................5 ENERAL ARE AND AINTENANCE ......................6 ACHINE PECIFICATIONS ..........................7 REPARATION ......................8 SSEMBLING ACHINE ................10 PTIONAL NCREMENTAL DDER EIGHT YSTEM ......................13 PTIONAL CCESSORY & I ....................14 ABLE OUTING NFORMATION ........................... -
Page 4: Safety
AFETY 1. Review and understand all of the warning labels affixed to this machine and on the facility safety sign. Replace any warning label at first sign of wear. Labels and the Facility Safety Sign may be obtained from Paramount free of charge. 2. -
Page 5: General Care And Maintenance
ENERAL ARE AND AINTENANCE 1. Cable Ends: Inspect end fittings daily for wear. Replace cables at the first sign of wear or on an annual basis. If the cable tension has been adjusted, be certain that the cable nut is tight. 2. -
Page 6: Machine Specifications
ACHINE PECIFICATIONS E A T U R E S • Two independent weight stacks (170 lb. per stack) • 2:1 weight stack reduction for low momentum movements. • 85 lb. max resistance at cable end (per handle). • (17) weight stack settings in 5 lb. increments (5 lb. - 85 lb.) •... -
Page 7: Preparation
REPARATION H A R D W A R E B A G C O N T E N T S ITEM DESCRIPTION PART SELECTOR PIN, MAGNETIC B 470 MOLDED FOOT S 550 SNAP HOOK B1005 STRAP HANDLE B1110A WEIGHT STACK LABEL B2173 85 LBS (38.5 KG.) W E I G H T P L A T E R E Q U I R E M E N T S... -
Page 8: Assembling The Machine
SSEMBLING THE ACHINE ASSEMBLE FEET TO BASE FRAME INSTALL WEIGHT PLATES GUIDE ROD RETAINER 1. Remove the rear panel held in place by the three thumbscrews at the top. CAP PLATE 2. If you ordered the optional adder GUIDE RODS weight system, remove the adder weight guide rods by pulling down on the adder weight guide rod retainers... - Page 9 SSEMBLING THE ACHINE INSTALL WEIGHT STACK LABELS 1. Verify that there are 16 weight plates installed on each stack. 2. Wipe the front surface of the weights with isopropyl alcohol and allow to dry completely. 3. Remove the backing from the label. Vertically center the 10 lb. label on the top weight and align the side of the label liner (front surface) with the outside edge of the pin hole in the weights.
-
Page 10: Optional Incremental Adder Weight System
PTIONAL NCREMENTAL DDER EIGHT YSTEM If you purchased your machine with the optional incremental adder weight system, it has been pre- installed. If you ordered the adder weight system after receiving the machine, these instructions will show you how to properly assemble it. The following parts are included with your kit: ITEM P UMBER ESCRIPTION... - Page 11 PTIONAL NCREMENTAL DDER EIGHT YSTEM E. Remove the pulley housing from the cap SEE TABLE ON PREVIOUS plate by unscrewing it from the selector PAGE FOR ITEM NUMBERS bar. F. Assemble the adder weight selector mechanism, thrust washers, wave spring PULLEY HOUSING washer, cover, and label plate to the cap plate as shown.
- Page 12 PTIONAL NCREMENTAL DDER EIGHT YSTEM L. Assemble the spring and adder weight guide rod retainer sleeves as shown. Test the adder weight selector mechanism. Make sure that it engages into the adder weight smoothly. Lubricate the guide rods using a Teflon based spray lubricant.
-
Page 13: Optional Accessory Kit
PTIONAL CCESSORY ANGER If you purchased the optional accessory kit, these instructions will show you how to properly assemble it to your machine. 1. Remove the rear panel. REMOVE BOLTS 2. Remove the two bolts holding the balance bar. Have someone support the bar while you remove the bolts. -
Page 14: Cable Routing & Information
& S ABLE OUTING PECIFICATION CABLE RETAINER SCREWS REPLACE CABLES at the first sign of wear OR on an annual basis! Part number: PFT2010CBL100X... -
Page 15: Machine Labels
ACHINE ABELS The following are the Warning labels required for this PFT-200 machine. If any of these labels are missing or become damaged contact Paramount. Note: these labels are not to scale. B2051 B2084 LBL-PR-PFT200A LBL-WRN-PFT200A B2173 B2612 BE ALERT! -
Page 16: Machine Disassembly
ACHINE ISASSEMBLY If you need to disassemble your machine for any reason (i.e. maneuver the machine through small doorway during installation), the diagram on the following page will show you the frame clamping locations. You will need the following tools: •Ratchet (1/2”... - Page 17 ACHINE ISASSEMBLY STEP 6 STEP 5 STEP 4 Pivot Column Support Column STEP 5 STEP 8...
-
Page 18: Service
ERVICE O W T O B T A I N E R V I C E For warranty service, contact an Authorized Paramount Dealer or a Paramount Customer Service representative at 1-800-721-2121 or 1-323-721-2121. You can also email us at nasales@paramountfitness.com. -
Page 19: Paramount Limited Warranty
Paramount. This limited warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. Contact Paramount Fitness Corp., 6450 E. Bandini Blvd., Los Angeles, California 90040-3185, for a list of authorized dealers or before returning any defective equipment. - Page 20 Paramount Fitness Corporation 6450 E. Bandini Blvd. Los Angeles, CA 90040-3185 Phone: 1-323-721-2121 Fax: 323-724-2000 1-800-721-2121 www.paramountfitness.com AM-PFT-200A.fm REV:6/9/10...