Page 2
AFETY 1. Review and understand all of the warning labels affixed to the machines and the facility safety sign. Replace any warning label at first sign of wear. Labels and the Facility Safety Sign may be obtained from Paramount free of charge. 2.
MAINTENANCE 1. Frames: Wipe all machines down with a damp cloth and dry completely each day. This includes painted, chrome parts and upholstered pads. 2. Painted/chrome parts: Use Simple Green or similar cleaner for light dirt and grime. Use TurtleWax® Polishing Compound or a good car polish to remove heavier dirt and grease as well as for polishing.
Page 6
HARDWARE BAG 0701-3: B 900A (8) 0701595 8001593 (2) 8001594 (2) HARDWARE BAG 0701-2: B582 (2) 0701597 (4) 0701596 (4) B 447 B1081 (4) B 921 (4) B 1004 (2) B 460 B 682 (2) B1036 MINIMUM FLOOR AREA REQUIRED: MACHINE WEIGHT (NOT INCLUD- ING WEIGHT OF USER): W/170LB STACK...
HARDWARE BAG 0701-1: 3/8-16 x 1 1/4 HHCS 3/8-16 x 1 BHCS 3/8 Split Washer 3/8 Black Washer 3/8 Metal Baser 3/8-16 Locknut 3/8 Black Washer 3/8 Metal Base Plastic Cover for 3/8 3/8-16 x 2 3/4 HHCS 3/8-16 x 3 HHCS Plastic Cover for 3/8 3/8 Black Washer (2) 3/8-16 Thin Locknut...
Page 8
0701550X 0701560X 0793100 0701520X H (2) C 457 F (2) C 955A (2) C 766A C 754B (2) C 955 NOTE: WHEN INSTALLING HARDWARE, TIGHTEN BY HAND ONLY UNTIL ALL COMPONENTS ARE ASSEMBLED. BOLT HEADS SHOULD FACE TO OUTSIDE OF MACHINE WHERE POSSIBLE.
Page 9
F (2) 0701540X G (2) 0701599 (2) 0701600 B 900A (6) R (5) To Weight Stack Diagram A Diagram A A (4) 0701596 (2) 0701597 (2) B1004 MAKE SURE NUT IS TIGHT! 9094170X...
Page 10
C 446 C 732 0794075X C 754 0701530 0701595 Diagram B Note: Adjust bolt to level machine and remove rocking. C 451 C 955A (2) C 766A C 754B (2) Diagram B C 955 A (4) B 900A B1004 94501X 0701610 0701596 (2) 0701597 (2)
8001594 (2) 8001125X 8001593 (2) 0101520X C 766A (2) C 955 (2) C 754B (2) C 955A (if needed) K (2) WEIGHT STACK INSTALLATION Review the equipment order to determine P/N: B1602 the weight stack configuration. The Comprised of boxes are marked with the quantity and (4) EACH 10lb MACHINED WEIGHT PLATES weight of the plates.
NOTE: TIGHTEN HARDWARE BY HAND ONLY AT THIS POINT. 0701600 B 460 NOTE: PARAMOUNT SELECTOR PIN B 460 IS THE ONLY PIN THAT SHOULD BE USED WITH THIS MACHINE. UNDER NO CIRCUMSTANCES SHOULD THE CAP PLATE OR WEIGHT STACK BE PINNED IN AN ELEVATED POSITION. 9099780X 0701501X (2) WEIGHT...
Page 13
B (2) B 447 D 840 (2) 3” (7.6cm) 9099780X NOTE: MOVE CAP PLATE 9099780X UP TO PULLEY HOUSING TO SET THE CORRECT GUIDE ROD AND BRACKET SPACING. NOW COMPLETELY TIGHTEN HARDWARE. CAP PLATE SHOULD MOVE SMOOTHLY ALONG GUIDE RODS. IF NOT, LOOSEN HARDWARE AND RESET SPACING. MAKE SURE MAX! LOCKING NUT...
Page 14
ELECT ITNESS WEIGHT STACK LABELS Hardware Bag 0701-4 is packed with a weight stack number label set. Follow the instructions printed on the label. Below is a list of weight stacks and the corresponding label set part num- bers: Wt. Stack 170lb 250lb Part No.
WARNING LABELS The following warning labels are affixed to the SF-0700. Be certain that you and the facility staff are aware of the meaning and importance of each label. If the labels become damaged, replacements can be ordered free of charge from Paramount.