Related Manuals for Paramount Fitness SF-1000
Summary of Contents for Paramount Fitness SF-1000
- Page 1 ELECT ITNESS IRCUIT SF-1000 SHOULDER PRESS ASSEMBLY MANUAL AM-SF-1000 Rev 01/02...
- Page 2 AFETY 1. Review and understand all of the warning labels affixed to the machines and the facility safety sign. Replace any warning label at first sign of wear. Labels and the Facility Safety Sign may be obtained from Paramount free of charge. 2.
-
Page 3: Maintenance
AINTENANCE 1. Frames: Wipe all machines down with a damp cloth and dry completely each day. This includes painted, chrome parts and upholstered pads. 2. Painted/chrome parts: Use Simple Green or similar cleaner for light dirt and grime. Use TurtleWax® Polishing Compound or a good car polish to remove heavier dirt and grease as well as for polishing. -
Page 4: Tools Required
TOOLS REQUIRED: WRENCH 7/16” (11mm) ALLEN WRENCH 1/2” (13mm) SOCKET 9/16” (14mm) 5/32” (4mm) 7/16” (11mm) RUBBER 7/8” (22mm) SOCKET SOCKET 3/16” (5mm) 9/16” (14mm) MALLET WRENCH WRENCH 15/16” (24mm) 5/16” (8mm) 3/4” (19mm) SF-1000CTN1: 8093040 STABILIZER FOOT 8001520X SEAT PAD 8001540X BACK PAD 9099780X... -
Page 5: Rear Support Assembly
SF-1000CTN2: 1001540X SEAT BACK 1601570X LIFTING ARM ASSY. 1601530X BOTTOM CROSS BRACE 1601580 1001520 CONNECTING BRACE BASE ASSY. 8001525 ADJ. SEAT ASSY. 1601550 REAR SUPPORT 1001560X ASSEMBLY PIVOT BRACE ASSY. -
Page 6: Hardware Bag
HARDWARE BAG 1001-2: B1117 (2) B 582 (2) B 447 B1182 (8) B 682 (6) B 921 (6) B 460 B1295 (2) B1121A (4) B1015 B 900 (3) B 898 HARDWARE BAG 1001-1: 3/8-16 x 1 BHCS 3/8 Black Washer 3/8-16 x 4 HHCS 3/8-16 Locknut 3/8-16 x 3 HHCS... - Page 7 MINIMUM FLOOR AREA REQUIRED: MACHINE WEIGHT (NOT INCLUD- ING WEIGHT OF USER): W/ 170LB STACK 391 LB W/ 250LB STACK 471 LB SHROUD OPTION +30 LB 51” (130cm) 87” (221cm) IN USE 55” (140cm) Height= 60 inches (152cm) 91” (231cm) IN USE NOTE: THIS MACHINE IS DESIGNED FOR USERS WEIGHING 300LB OR LESS...
- Page 8 TOP VIEW Pulley Housing 1001510X 1001540X 1601550 8093040 H (2) F (4) 1001520 1601530X G (2) NOTE: WHEN INSTALLING HARDWARE, TIGHTEN BY HAND ONLY UNTIL ALL COMPONENTS ARE ASSEMBLED. BOLT HEADS SHOULD FACE TO OUTSIDE OF MACHINE WHERE POSSIBLE. BE SURE ALL HARDWARE IS TIGHT BEFORE USING MACHINE.
- Page 9 F (2) 1601580 1001560X D (2) I (2) D (2) 1601570X C 678 (2) D2004 1601566...
-
Page 10: Weight Stack Installation
8001540X 8001520X 8001525 N (2) 8001539 S (2) B1295 (2) WEIGHT STACK INSTALLATION Review the equipment order to determine P/N: B1602 the weight stack configuration. The Comprised of boxes are marked with the quantity and (4) EACH 10lb MACHINED WEIGHT PLATES weight of the plates. -
Page 11: Front View
FRONT VIEW NOTE: TIGHTEN HARDWARE BY HAND ONLY AT THIS POINT. B (2) B 447 9099780X 9000801X (2) WEIGHT PLATES 1001600 C 757 (2) B 582 (2) NOTE: IF INSTALLING THE WEIGHT SHROUD OPTION REFER TO THE INSTALLATION INSTRUCTIONS PROVIDED WITH THE OPTION. B 460 NOTE: PARAMOUNT SELECTOR PIN B 460 IS THE ONLY PIN THAT SHOULD BE USED WITH... - Page 12 9099780X NOTE: MOVE CAP PLATE 9099780X UP TO PULLEY HOUSING TO SET THE CORRECT GUIDE ROD AND BRACKET SPACING. NOW COMPLETELY TIGHTEN HARDWARE. CAP PLATE SHOULD MOVE SMOOTHLY ALONG GUIDE RODS. IF NOT, LOOSEN HARDWARE AND RESET SPACING. B 898 1001600 B 900 L (4)
- Page 13 ELECT ITNESS WEIGHT STACK LABELS Hardware Bag 1001-3 is packed with a weight stack number label set. Follow the instructions printed on the label. Below is a list of weight stacks and the corresponding label set part numbers: Wt. Stack 170lb 250lb Part No.
-
Page 14: Warning Labels
WARNING LABELS The following warning labels are affixed to the SF-1000. Be certain that you and the facility staff are aware of the meaning and importance of each label. If the labels become damaged, replacements can be ordered free of charge from Paramount. -
Page 15: Day Warranty
Contact Paramount Fit- ness Corp., 6450 E. Bandini Blvd., Los Angeles, California 90040-3185, before returning any defective equipment. Paramount Fitness Corp. © 1999. Paramount Fitness Corp. © 1993, 1995, 1997...