Related Manuals for Paramount Fitness MS-1000
Summary of Contents for Paramount Fitness MS-1000
-
Page 1: Assembly Manual
ASSEMBLY MANUAL OPTIONAL STATION MS-1000/1050 ADJUSTABLE CABLE COLUMN MS-1000 Right Side MS-1050 Left Side AM-MS1000.fm Rev 04-02... -
Page 2: Safety Requirements
14. Follow the installation guidelines provided with the products. 15. Retain these instructions for future reference. If you have any questions, do not hesitate to contact your Paramount Dealer of Paramount Fitness Corp. at (800) 721-2121 or www.paramountfitness.com. Refer to Maintenance Schedule label located on the machine for maintenance intervals. -
Page 3: Maintenance Requirements
MAINTENANCE REQUIREMENTS • Frames: Wipe all machines down with a damp cloth and dry completely each day. This includes painted and chrome parts and upholstered pads. • Painted/chrome parts: Use Simple Green or similar cleaner for light dirt and grime. Use Tur- tleWax®... -
Page 4: Tools Required
HARDWARE MEASUREMENT GUIDE As shown below, Button Head, Socket Head and Hex Head screw length is measured from the bottom of the head to the end of the screw. The length of Flat Head screws is measured as the total overall length. BHCS - BUTTON HEAD CAP SCREW SHCS - SOCKET HEAD CAP SCREW FHCS - FLAT HEAD CAP SCREW... - Page 5 MS-1000/1050 ASSEMBLY INSTRUCTIONS 1. Your MS-1000 (right side handle) or MS-1050 (left side handle) adjustable cable col- umn stations require minimal assembly to complete. These assembly instructions may vary slightly depending upon the method of shipment. 2. To complete the installation, you will need an available side “A” on a 4-sided modular frame.
- Page 6 - (2) Side “A” Stations. - (6) Side “B” Stations. IMPORTANT! IF YOU DID NOT ORDER AN OPTIONAL SIDE “A” STATION FOR ANY OF THE ABOVE CONFIGURATIONS, A HALF-BLANK STATION (MS-0005) MUST BE INSTALLED IN PLACE OF EACH SIDE “A” STATION. MS-1000 PT1.fm...
- Page 7 MS-1000 COMPONENTS RIGHT SIDE (see following page for left side) Note: Depending upon the method of shipment, some of the items that appear may already be assembled to your machine. 351-1/2 in. (893 cm) MS1002090 MS1002000X CABLE TOP PULLEY HOUSING (RIGHT)
- Page 8 CABLE TOP PULLEY HOUSING (LEFT) MS1002050X MS1002030X HANDLE ADJUSTABLE PULLEY (LEFT) MS8002002 MS1002020X BEAM CONNECTOR CAP PLATE PULLEY MS1002061 B5000 ADJUSTMENT ADJUSTMENT COLUMN LABEL MS1002015X B1100 9099780X MS8002009X BOTTOM PULLEY HANDLE SELECTOR BAR HOUSING (LEFT) GUIDE ROD (2) MS-1000 PT1.fm...
- Page 9 MS-1000/1050 HARDWARE BAG Note: You may have extra connecting hardware if additional stations are added to the modular frame ITEM DESCRIPTION PART # HEX HEAD CAP SCREW, 1/2-13 x 2-3/4” lg. C470A WASHER, FLAT, 1/2” C755A NUT, LOCKING, 1/2-13 C743A CAP, FOR 3/8”...
- Page 10 MS-1000/1050 HARDWARE BAG (CONTINUED) ITEM DESCRIPTION PART # WASHER, FLAT, 1” I.D. C757A BUMPER, WEIGHT PLATE B582 PULLEY WHEEL B900 HANDLE, PULLEY HOUSING MS1002063 CAP, PULLEY HOUSING HANDLE B1150 STOP, PULLEY HOUSING MS1002062 GUIDE ROD RETAINING BRACKET B447 QUICK LINK, HEX COUPING...
-
Page 11: Weight Plate Installation
B1602 ASSEMBLE THE CAP PLATE PULLEY HOUSING, SELECTOR PIN AND SELECTOR BAR. FULLY THREAD PULLEY HOUSING INTO SELECTOR MS1002020X BAR. MAKE SURE PULLEY HOUSING IS PARALLEL WITH SIDES OF CAP PLATE. FULLY TIGHTEN LOCKING B460 NUT. 9099780X MS-1000 PT2.fm... -
Page 12: Install Weight Plates
INSTALL WEIGHT PLATES DO NOT TIGHTEN 18, 19, 7 UNTIL CABLE IS INSTALLED CAP PLATE ASSEMBLY MS8002009X MS-1000 PT2.fm... - Page 13 Take the time during installation to align the label with the edge of the pin hole and the top surface of the weights to get all of the individual labels straight. Liner Individual labels Align with outside edge of pin holes MS-1000 PT2.fm...
- Page 14 MS1002000X (right side) BEAM. 1, 2 4, 8, 6, 7 3, 2 6. ASSEMBLE THE BOTTOM PULLEY HOUSING MS1002015X (left side shown) MS1002010X (right side) 7, 6, 8, 4 DISCARD 3/8 X 3-3/4” 4, 9, 6, 7 BOLT. MS-1000 PT2.fm...
- Page 15 7. ASSEMBLE THE ADJUSTABLE COLUMN AND PULLEY HOUSING 4, 8, 6, 7 4, 14, 6, 7 MS1002061 MS1002030X (left side shown) MS1002035X (right side) PLACE ADJUSTABLE PULLEY HOUSING IN THE MIDDLE POSITION (10th HOLE FROM THE BOTTOM). 4, 8, 6, 7 4, 13, 6, 7 MS-1000 PT2.fm...
- Page 16 7. Adjust the pulley housing through the entire range to check that the indicator lines up with numbers (1) and (22). 8. Firmly press the label to the upright. MS-1000 PT2.fm...
- Page 17 9. INSTALL CABLE, PULLEYS AND HANDLE CABLE ROUTING DIAGRAM MS1002090 START HERE B1100 SOME MEMBERS HAVE BEEN REMOVED FOR CLARITY. SEE FOLLOWING PAGE FOR PULLEY HARDWARE. MS-1000 PT3.fm...
- Page 18 25, (9) places 4, 5, 6, 7 27, 15, 26, 7 4, 8, 6, 7 4, 5, 6, 7 8, 20 4, 8, 6, 7 4, 8, 6, 7 4, 5, 6, 7 4, 5, 6, 7 10, 20 MS-1000 PT3.fm...
- Page 19 Guide Rod Bracket. This will set the correct guide rod spacing. 1/4” Set Collars to allow 1/4” Gap between the bottom of Label Plate and Pulley Housing. Travel Stop Collar Move Weight Selector Bar UP to set guide- rod spacing. MS-1000 PT3.fm...
-
Page 20: Assemble Handle
12. ASSEMBLE HANDLE MS1002050X 4, 8, 6, 7 4, 11, 6, 7 MS-1000 PT3.fm... - Page 21 D) Adjustment Pins: Check the function of the selector pins on adjustable pulley hous- ings and pad position adjustments. Make sure that the selector pin inserts completely into each position without binding. MS-1000 PT4.fm...
-
Page 22: Miscellaneous Labels
STATION DESCRIPTION PART # LENGTH MS-1000/1050 Single Adjustable MS1002090 Cable Column 351-1/2 in. (893 cm) MISCELLANEOUS LABELS The following labels are affixed to the adjustable cable column stations on the MS-Series of machines. B5000 ® MODULAR SYSTEM B2580 MS-1000 PT4.fm... -
Page 23: Warning Labels
Use only the Paramount pin shown REPLACE IF DAMAGED. 2. Bolt height must not exceed 1 3/8”. Check P/N B2060 ASTM F1749 regularly. Make sure locking nut is tight. Paramount Pin P/n B 460 ASTM F1749 P/N B2141 B2060 B2141 MS-1000 PT4.fm... - Page 24 Contact Paramount Fitness Corp., 6450 E. Bandini Blvd., Los Angeles, California 90040-3185, before returning any defective equipment. Paramount Fitness Corp. © 2002.
- Page 25 MS-1000/1050 HARDWARE BAG Note: You may have extra connecting hardware if additional stations are added to the modular frame ITEM DESCRIPTION PART # HEX HEAD CAP SCREW, 1/2-13 x 2-3/4” lg. C470A WASHER, FLAT, 1/2” C755A NUT, LOCKING, 1/2-13 C743A CAP, FOR 3/8”...
- Page 26 MS-1000/1050 HARDWARE BAG (CONTINUED) ITEM DESCRIPTION PART # WASHER, FLAT, 1” I.D. C757A BUMPER, WEIGHT PLATE B582 PULLEY WHEEL B900 HANDLE, PULLEY HOUSING MS1002063 CAP, PULLEY HOUSING HANDLE B1150 STOP, PULLEY HOUSING MS1002062 GUIDE ROD RETAINING BRACKET B447 QUICK LINK, HEX COUPING...