Assembly; Operation Instructions - Worx WG151 User Manual

AssEMBLY

1. aSSEmBLy oF THE SaFETy GuaRd
(See Fig a)
Attach the safety guard to the trimmer head.
Align the guard so it slides into the slots
located on the trimmer head. Turn the tool
over and secure the safety guard onto the
trimmer head with the screw (a) provided.
2. aSSEmBLy oF THE EdGER wHEEL
(See Fig B)
With the tool rightside up, slide the edger
wheel assembly onto the metal plate located
on the side of the trimmer head. Make sure
the groves of the edger wheel assembly locks
onto the metal plate, you will hear it click into
place.
To remove the wheel assembly, press the
release button (b) on the wheel and pull the
wheel assembly upward.

oPErATIoN INsTrUCTIoNs

waRNiNG! The charger and battery
pack are specially designed to work
together so do not attempt to use any other
devices. Never insert or allow metallic objects
into your charger or battery pack connections
because of an electrical failure and hazard will
occur.
1. BEFoRE uSiNG youR CoRdLESS
GRaSS TRimmER
Your battery pack is UNCHARGED and it must
be fully charged once before it is used.
The battery charger supplied is matched to the
Li-ion battery for use with this tool. Do not use
another battery charger.
2. CHaRGiNG youR BaTTERy PaCk
The Li-ion battery is protected against deep
discharging. When the battery is empty, the
trimmer will switch off by means of a protective
circuit: The trimmer head will stop rotating.
Note: In a warm environment or after heavy use,
the battery pack may become too hot to permit
charging. Allow time for the battery to cool
down before recharging.
2-in-1 Cordless Li-ion Grass Trimmer/Edger
3. To REmovE oR iNSTaLL BaTTERy
PaCk (See Fig C)
Depress the battery release button to
remove battery pack from your trimmer.
After recharging, insert the battery pack onto
trimmer's battery bracket. A simple push and
slight pressure will be sufficient.
4. SaFETy oN/oFF SwiTCH (See Fig d)
The safety switch is locked off to prevent
accidental starting. Depress the lock off button
(c) then depress the on/off switch (d) and
release lock off button (c). Your trimmer is now
on. To switch off, just release the on/off switch.
waRNiNG! The cutting head
continues to rotate after the
trimmer has been switched off; wait until
it has completely stopped then lay down
the tool.
5. adJuSTmENT oF THE TELESCoPiC
SHaFT (See Fig E)
Unscrew the locking collar (4) in the direction
indicated to unlock, turn it clockwise.
Adjust the length of the telescopic shaft to the
most comfortable length.
Tighten the locking collar (4) in the direction
indicated to lock, turn it counterclockwise.
6. maiN HaNdLE RoTaTioN (See Fig F1,
F2)
While holding the trimmer head (14), pull
upward on the upper shaft (19) and rotate it
90 degrees clockwise then allow it to drop
back into the lower shaft coupling (18). When
released back into the lower shaft coupling,
the upper shaft will be locked into position
automatically.
7. adJuSTmENT oF auxiLiaRy HaNdLE
Pull up the auxiliary handle locking lever (5).
Hold the locking lever and rotate the auxiliary
handle to the most comfortable and balanced
position (See Fig G)
8. adJuSTmENT oF THE TRimmER
HEad aNGLE To THE SHaFT
To adjust the upper shaft angle downwards
or convert the tool from trimming mode to
edging mode, put one foot on the motor
housing portion of the trimmer head (20), then
11 11
EN