Table of Contents
Advertisement
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off and
when it is running idle but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades
Maintain this tool in accordance with these instructions
and keep well lubricated (where appropriate)
If the tool is to be used regularly then invest in anti
vibration accessories.
Plan your work schedule to spread any high vibration tool
use across a number of days.
ASSEMBLY & OPERATION
ACTION
Assembly
Assembling the Trimmer Shaft
Assembling the Auxiliary Handle
Assembling the Safety Guard
Installing and Removing the
Battery Pack
NOTE:
• This machine will only run
14
when 2 batteries are installed. It
is recommended to use the same
two batteries and charge the two
batteries at the same time.
• When you use two batteries
with different power, the
machine will only run to the
lower common denominator.
Charging the battery pack
NOTE:
• The batteries are shipped
uncharged. Each battery must
be fully charged before the first
use.
• Always fully charge the two
batteries at same time. More
details can be found in charger's
manual.
OPERATION
On/Off Switch
WARNING! The cutting
head continues to rotate
after the trimmer has been
switched off; wait until it has
completely stopped then lay
down the tool.
Trimming
Cordless Grass Trimmer
-Adjusting the Auxiliary handle
Manually feeding the line
Removing the Cap
Cutting Head
Changing the line spool
Manually winding the line
OPERATION INSTRUCTIONS
attempt to use any other devices. Never insert or allow
metallic objects into your charger or battery pack
FIGURE
connections because of an electrical failure and
hazard will occur.
1. AUTOMATIC LINE FEED SYSTEM
See Fig. A
When initially switching on the trimmer, a small length
See Fig. B
of line is fed out.
A 'clattering' noise will be heard for a short time. This
See Fig. C
is normal and is caused by the line being cut by the line
cutter. Once the line is cut to the correct length, the
'clattering' noise will stop and the trimmer motor will
run at full speed.
To feed more line, stop the trimmer completely, then
restart, allowing the motor to reach full speed. Repeat
this until you hear the 'clattering' noise of the line
See Fig. D1,D2
cutting. (Do not repeat this procedure more than 6
times)
2 . MANUALLY FEEDING THE LINE (See Fig. H)
Press and release manual line feed button, whilst
gently pull out the lines until the lines reaches the line
cutter. When the required amount of line is fed out,
gently pull on the second line (there is no need to press
the manual line feed button again). If the line extends
past the line cutter, too much line has been fed out.
If too much line is fed out, remove the spool cap and
See Fig. D3
rotate the spool anti-clockwise until the line is at the
desired length.
Removing the Cap (See Fig. I)
Press and hold in the two latches. Pull the spool cap
away from the Cutting Head. Keep the cap and spool
holder clean from debris. To replace the cap, press
it firmly towards the spool holder. Ensure that it is
correctly connected by trying to remove it without
depressing the two latches.
Changing the Line Spool (See Fig. K, L)
See Fig. E
First take off the cap and remove the old spool. Place
new spool into cutting head. Feed one line through the
eyelet, then repeat for second line (See Fig. L).
Release line from cleat on the Spool. Reattach the cap.
See Fig. F
WARNING! The charger and battery pack are
specially designed to work together so do not
WARNING! Your Trimmer is designed to only use
line with a maximum diameter of 0.065"(1.65mm).
See Fig. G
See Fig. H
See Fig. I
See Fig. J
See Fig. K,L
See Fig. M, N,O,P
WG183E
WG183E.X
Advertisement
Table of Contents
