JVC GY-DV550U Instruction Manual page 29

2-10 Indications in Viewfinder (Cont'd)
● Status 1
In addition to the information on the Status 0 screen, this screen displays audio indicators and information on remaining
tape, voltage and lens F-number (or FILTER POSITION).
Display position
8
(Example)
CH1- - - - + - -
CH2- - - - + - -
9
STBY
SAVE
STOP
REC
FF
REW
EJECT
0 (Example)
< 60
(Example)
12: 34: 56: 20
A
(Example)
12.4V
B
F-number:
OPEN, F2, F2.8, F4,
F5.6, F8, F11, F16,
CLOSE
FILTER:
FIL1, FIL2, FIL3
(Example)
C
M: 099
EXT, INT, PARA
D
REC2
E
● Status 2 ... Not displayed during external video signal input or IEEE1394 input.
This screen displays the camera setup statuses.
Event display is not available while this screen is displayed.
Indication
SCENE FILE
WHITE BAL
FILTER
SHUTTER
GAIN
IRIS LEVEL
FULL AUTO
REC TIME
2. CONTROLS, INDICATORS AND CONNECTORS
Display
Shows the input level of the audio input channel.
Display ON/OFF can be selected using the VF DISPLAY menu screen.
See "AUDIO DISPLAY" on page 78.
VCR in standby mode
VCR in save mode
VCR in stop mode
VCR in record mode
VCR in fast-forward mode
VCR in rewind mode
VCR in eject mode
Remaining tape indication (displayed in 1-minute steps)
When the tape is used for a long time, the remaining tape may not be
indicated accurately. At the beginning of the tape, in particular, the indication
may show smaller value than the actual one.
Time code display
Time code display is available when the "REC TIME" item on the VF DISPLAY
menu screen is set to TIME CODE.
See "REC TIME" on page 78.
Voltage indication (displayed in 0.1 V steps) The indicator flashes when the
battery is low. The indicator will not appear when the camera remote control
unit is connected.
The F-number of the connected lens or the filter position of the unit is displayed.
Whether to display the F-number or filter position, or no display is selected in
F. NO/FILTER of the VF DISPLAY screen.
• The F-number may not be displayed depending on the lens type or when
the lens is removed. See page 78
Not displayed during external video signal input or IEEE1394 input.
In the Super Scene Finder (S.S.F.) mode, the number of memorized scenes
is shown.
M : In MARK mode
C : In CUE mode
Number: Number of memorized scenes
Displays whether the main unit is used for recording or the external VCR
connected to the VTR/RM multi-pin connector.
The displays will differ depending on the VTR SELECT switch setting.
INT is constantly displayed during external video input or IEEE1394 input.
INT is constantly displayed when the VTR/RM switch is set to RM.
The display will light during external VCR recording.
The display flashes when there is a warning on the external VCR.
The display will not appear when the VTR/RM switch is set to RM.
A, B, OFF
A, B, PRESET, FAW, MANUAL (When remote control unit w/manual balance is connected.)
3.2K, 5.6K+1/8ND, 5.6K+1/64ND
OFF, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/60.1 to 1/2084.6 (in VARIABLE mode),
EEI (in ALC mode)
-3dB, 0dB, 3dB, 6dB, 9dB, 12dB, 18dB, LOLUX, ALC
NORMAL, BACK L, SPOT L
ON, OFF
Remaining tape time or time code.
Function
Note:
When the RS-232C cable
is connected, the VCR
operation mode may not
be displayed correctly.
Indication Contents
29