Table of Contents
Advertisement
For servicing
→
See the service manual page 1-16 "1.11.7 Tripod base".
3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS
3-6 Attaching the Tripod Base (provided)
1.
Tripod mounting holes
Front mount clip
2.
Safety lever
2.
Lock lever
4.
Front
base
mount
3.
Rear base
mount
Front mount clip
Pin
4.
OPERATE/WARNING
LIGHT
RESET
ON
OFF
MONITOR
FILTER
SELECT
COUNTER
CTL
1 3200k
ALARM
TC
2 5600k
UB
3 5600k+ND
SHUTTER
STATUS
MONITOR
MENU
CH-1
AUDIO
CH-2
LEVEL
AUTO IRIS
FULL AUTO BLACK
LOLUX
BACK L
STRETCH
NORMAL
NORMAL
SPOT L
COMPRESS
POWER
NG
ON
OFF
Use the provided tripod base to place the camera on a tripod.
1.
Attach the tripod base on the tripod by using the hole that
balances the unit most optimally.
2.
While pushing the safety lever, pull the lock lever toward
the front until the front mount clip clicks into place.
3.
Place the unit on the tripod base by aligning the rear base
mount of the unit with the pin on the tripod base.
4.
Push the unit from the upward direction and slide it toward
the front so that the front base mount of the unit is locked
by the front mount clip of the tripod base as it clicks into
place.
CAUTION:
• The front base mount may be locked while the pin of the
tripod base is not inserted into the hole on the rear base
mount of the unit. Therefore, after mounting, make sure
that these parts are engaged properly.
• When moving the unit mounted on a tripod, any impact
or vibration should be avoided as this may cause the unit
to become detached and to drop from the tripod.
Be sure to remove the unit from the tripod before
transporting it.
3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS
3-7 Inserting and Replacing Backup Lithium Batteries
The GY-DV500 uses a lithium battery for backup of the time code data. Install the provided lithium battery before actually using the
unit.
● Lithium battery: CR2032
RESET
MONITOR
FILTER
SELECT
1 3200k
ALARM
2 5600k
3 5600k+ND
SHUTTER
STATUS
MONITOR
MENU
CH-1
AUTO IRIS
FULL AUTO BLACK
LOLUX
BACK L
STRETCH
NORMAL
NORMAL
SPOT L
COMPRESS
NG
POWER
ON
OFF
Power switch
When the lithium battery is not in place or the battery is exhausted and requires a replacement, the "Li" indicator in the LCD display
will light up.
Replace lithium batteries with the POWER switch set to ON. Doing it with the POWER switch set to OFF will cause the loss of
backup data.
How to Install the Lithium Battery
Lithium battery cover
LITHIUM BATT.
1.
Push the lithium battery cover in the direction of the arrow
as illustrated and remove the cover.
2.
Slide the battery into place with its
upward.
3.
Return the lithium battery cover to its original position in the
unit.
After replacing the lithium battery, set the date and time.
To do this, see page 41 "Setting the Date and Time".
33
34
"Li" indicator
CAUTION:
If the unit is not used for a lengthy period of time (one
month or more), remove the lithium battery. If the voltage
of the lithium battery becomes low, the set may malfunction.
OPERATE/WARNING
LIGHT
CH 1
OVER
AUTO OFF DEW
40 30
20
10
0 dB
ON
CH 2
OVER
SERVO
RF
L i
OFF
32k
48k
PB
NDF
HOLD
SP
AUD LOCK
MENU
COUNTER
H
M
S
F
E
BATT
F
CTL
CH-1
AUDIO
CH-2
REMAIN
REV FWD
TC
UB
H
M
LEVEL
CH-1
AUDIO SELECT
AUDIO INPUT
CH-1
AUDIO
CH-2
LEVEL
LITHIUM BATT.
Lithium battery case
How to Remove Lithium Batteries
marked surface facing
TC GENERATOR
CH-2
PRESET
FREE
AUTO
REGEN
REC
MANUAL
CH-2
CONTINUE
MENU
FRONT
REAR
GROUP
ITEM
SELECT
DATA SET
HOLD
SHIFT
ADVANCE
PRESET
The lithium battery is easily removed
if you press at the edge of the
lithium batter y at the place
indicated in the illustration on the
left and then pull the battery out.
Advertisement
Table of Contents
