Table of Contents
Advertisement
Chapter 4 Adjustments and Settings for Recording
Information Item
AWB A ACTIVE
Camera Warning
AWB B ACTIVE
and Report Area
AWB A OK
(related to AWB, ABB
AWB B OK
and switch settings)
AWB BREAK
AWB NG
AWB PRESET
ATW MODE
CHECK FILTER
AWB A VAR
AWB B VAR
ABB ACTIVE
ABB OK
ABB BREAK
ABB NG
W-SHD ACTIVE
W-SHD OK
W-SHD BREAK
W-SHD NG
B-SHD READY
B-SHD ACTIVE
B-SHD OK
B-SHD BREAK
B-SHD NG
(Switch changeover
WHITE: #
indication)
AUTO KNEE: ON/OFF
GAIN:
SS: 1/
SS:
SS: SUPER V
FILTER:
EXTENDER: ON/OFF
IRIS:
(Low light warning)
LOW LIGHT
(Y GET value)
(MARKER indication)
MKR: A/B/OFF
INH
User button
S.GAIN
functions
S.IRIS ON/OFF
UM: USER MAIN
I.OVR ON/OFF
button
S.BLK –
U1: USER1 button
U2: USER2 button
B.STR ON/OFF
AUDIO CH1
AUDIO CH2
REC SW
Y GET ON
RET SW
ATW ON/OFF
NEWS-G ON/OFF
SLOT SEL
PRE REC
USB
1 - 4
Filter position
-
A
WHITE BAL switch
B
position
P
T
Gain value
Indication
AWB being performed on Ch A.
AWB being performed on Ch B.
. K
AWB successful on Ch A.
. K
AWB successful on Ch B.
. K
AWB action aborted by user.
AWB action failed. The second line indicates the status.
COLOR TEMP LOW
COLOR TEMP HIGH
LEVEL OVER
LOW LIGHT
TIME OVER
. K
AWB cannot proceed because the AWB switch is positioned at [PRE].
AWB cannot proceed during ATW.
Make sure the FILTER control is positioned correctly.
. K
AWB cannot proceed because [A] is set to "VAR".
. K
AWB cannot proceed because [B] is set to "VAR".
ABB being performed.
ABB action successful.
ABB action aborted by user.
ABB action failed.
White shading being adjusted.
White shading has been adjusted.
White shading action aborted by user.
White shading adjustment failed due to excessive brightness.
LVL OVER
Black shading accepted (by holding down the ABB switch during ABB
adjustment).
Black shading being adjusted.
Black shading adjustment successful.
Black shading adjustment aborted by user.
Black shading adjustment failed.
. K
The WHITE BAL switch has been switched. # is replaced with A, B or PRE.
When [A] and [B] are set to "VAR", then it is indicated as VAR
[B] is assigned ATW, then it is indicated as ATW MODE.
AUTO KNEE switch has been switched to ON or OFF.
dB
Gain has been switched with the GAIN selector switch or a user button.
When the shutter speed has been switched, the shutter speed is indicated.
1/
Shutter speed is in SYNCRO SCAN mode.
Shutter speed is in SUPER V mode.
. K
Filter position and detail have been switched.
Lens extender has been turned on or off.
F
.
Indicated when the iris override correction value is to be changed.
Brightness too low.
. %
When the Y GET function is being carried out (the output brightness level
near the center marker is being measured for about three seconds: the level is
represented as a percentage), the output brightness level near the center
marker is indicated as a percentage.
Current marker type
User buttons disabled.
dB/OFF
Selected S.GAIN
Whether S.IRIS is ON or OFF.
Iris override can be set (the IRIS OVERRIDE setting is ON).
/OFF
Status of SUPER BLACK (ON or OFF). When it is ON, the set value is also
indicated.
Status of BLACK STRETCH (shade correction for the black level): ON or OFF
Input signal to be recorded on Audio Channel 1 has been switched.
Input signal to be recorded on Audio Channel 2 has been switched.
USER button acts as REC switch.
Y GET function ON.
USER button acts as RET switch.
ATW being performed.
Status of News Gamma (ON or OFF)
Switch that changes the target card is set.
Indicates that PRE RECORDING mode has been switched ON or OFF.
Indicates whether USB Drive Mode is ON or OFF.
Position of the CC/ND filter.
Filter not positioned correctly.
WHITE BAL switch positioned at [A].
WHITE BAL switch positioned at [B].
WHITE BAL switch positioned at [PRE].
ATW mode active. When brightness and color are outside operating limits, the
indication blinks.
dB
Current gain value.
Status
Color temperature too low.
Color temperature too high.
Brightness too high.
Brightness too low.
Action timed-out.
(continued)
.
K. When
47
4
Advertisement
Table of Contents
