Hws1800T - TDK-Lambada HWS?HWS User Manual

HWS
1800T
HWS1800T Specifications
ITEMS/UNITS
Voltage Range
Frequency
Power Factor (200VAC)(typ)
Input Efficiency (200VAC)(typ)
Current (200VAC)(typ)
Inrush Current (200VAC)(typ)
Leakage Current (240VAC)
Nominal Voltage
Maximum Current
Maximum Peak Current
Maximum Power
Maximum Peak Power
Maximum Line Regulation
Output Maximum Load Regulation
Temperature Coefficient
+25 to +71
Maximum
Ripple & Noise
(*4)
Hold-up Time (typ)
Voltage Adjustable Range
Over Current Protection
Over Voltage Protection
Remote Sensing
Remote ON/OFF Control
Function Output Voltage External Control
Parallel Operation
Series Operation
Monitoring Signal
Line DIP
Operating Temperature
-10 to +40
Environment Storage Temperature
Operating Humidity
Storage Humidity
Vibration
Shock (In package)
Cooling
Withstand Voltage
Isolation
Isolation Resistance
Safety Standards
EMI
Standards
Immunity
Weight (typ)
Mechanical
Size (W x H x D)
(*1) At Ta=25 and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA, EN) are required,
input voltage range will be 200 - 240VAC (50/60Hz).
(*3) First in-rush current. Not applicable to the first 0.2ms in-rush current flowing into the power supply noise filter.
(*4) Measure with JEITA RC-9131A probe, bandwidth of scope: 100MHz.
At 100uF electric capacitor and 0.47uF film capacitor on the test fixture board.)
Ripple noise spec for ambient temperature between -10 to 25 is a linearity value with respect to the -10 degrees
C and 25 degrees C specs.
(*5) 170 - 265VAC, constant load.
(*6) No load-full load, constant input voltage.
(*7) Constant current limit with automatic recovery. Over current condition for more than 5 seconds will cause the
output to shutdown.
Output current exceeding maximum rated output current for more then 10 seconds continuously will result to
output shutdown.
(*8) OVP circuit will shut down output, manual reset (power cycle) or ON/OFF CNT signal reset.
(*9) At 200VAC(50/60Hz), nominal output voltage and maximum output current.
(*10) Measured by the each measuring method of UL, CSA and EN (at 60Hz), Ta=25 .
(*11) Ratings - Derating at standard mounting.
- As for other mountings, refer to derating curve.
(*12) Peak output current is less than 10 seconds, and duty 35% max.
(Read instruction manual carefully, before using the power supply unit.)
MODEL
(*2) V
(*2) Hz
(*1)
(*1) 75 81
(*1) A 4.5
(*3) A
(*10) mA
VDC 3.3 5
A 300
(*12) A -
W 990
(*12) W -
(*5) mV 36
(*6) mV 60
150
mVp-p
0 mVp-p
-10 mVp-p 220
(*9) ms
VDC 2.64-3.96 4.0-6.0 4.8-7.2
(*7) A > 315.0 > 303.0
(*8) VDC 4.12-4.62 6.25-7.0 7.5-8.4 9.37-10.5 15.0-17.4 18.7-21.8 30.0-34.8 45.0-49.7 55.2-60.0 69.0-75.0
(*11)
W 990
+50 W 825 1250
+60 W 660 1000
+71 W 495
RH
RH
At no operating, 10 - 55Hz (sweep for 1min.) 19.6m/s² constant, X, Y, Z 1hour each.
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA),
Output-FG : 500VAC (300mA), (60V model 651VAC(390mA)), Output-CNT:100VAC (100mA) for 1min
More than 10M
Approved by UL60950-1, CSA C22.2 No.60950-1, EN60950-1
Built to meet EN55011/EN55022-A, FCC-ClassA, VCCI-ClassA.
Built to meet IEC61000-4-2(Level 2,3), -3(Level 3), -4(Level 3),
g 4000
mm
3 AC170 - 265
47 - 63
0.94
82 84
6.0
40
2.6 max
6 7.5 12 15
250 200 125 100
300 240 150 120
1500
1800
40 48 60
72 90
Less than 0.02%/
200
200
250
20
6.0-9.0 9.6-14.4 12.0-18.0 19.2-28.8 28.8-43.2 38.4-52.8 48.0-66.0
> 242.4 > 151.5 > 121.2
Possible
Possible
Possible
Possible
Possible
PF (Open collector output)
Built to meet SEMI-F47
-10 to +71, Start up -20 to +71
1500
1500
1125
750
-30 to +85
10 - 90 (No Condensing)
10 - 95 ( No Condensing )
Less than 196.1m/s²
Forced air by blower fan
More than 100M Output - FG : 500VDC
Output - CNT 100VDC at 25
-5(Level 3,4), -6(Level 3), -8(Level 4), -11
126.5 x 82 x 280 (Refer to outline drawing)
88 90
7.0
24 36 48 60
75 50 37.5 30
105 70 52.5 42
1800
2520
96 144 192 240
144 216 288 360
250 300 400
250 300 400
300 400 600
18
> 106.0 > 70.7 > 53.0 > 42.4
1800
1680
1300
900
and 70%RH
3800