Hws50/Hd - TDK-Lambada HWS?HWS User Manual

HWS
50/HD
HWS50/HD Specifications
ITEMS/UNITS
Voltage Range
Frequency
Power Factor (100/200VAC)(typ) (*2)
Input Efficiency (100/200VAC)(typ)
Current (100/200VAC)(typ)
Inrush Current (100/200VAC)(typ) (*4)
Leakage Current
Nominal Voltage
Minimum Current
Maximum Current
Maximum Power
Maximum Line Regulation
Output Maximum Load Regulation
Temperature Coefficient
Maximum Ripple & Noise (0<Ta<71 ) (*5) mVp-p
Maximum Ripple & Noise ( 10<Ta< 0 ) (*5) mVp-p
Hold-up Time (typ)
Voltage Adjustable Range
Over Current Protection
Over Voltage Protection
Remote Sensing
Function
Parallel Operation
Series Operation
Line DIP
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Environment
Vibration
Shock (In package)
Cooling
Withstand Voltage
Isolation
Isolation Resistance
Safety Standards
PFHC
Standards
EMI
Immunity
Weight (typ)
Mechanical
Size (W x H x D)
(*1) Output voltage might be unstable when start up at -40 to -10
(*2) At 100/200VAC, Ta=25 and maximum output power.
(*3) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - 240VAC
(50/60Hz).
(*4) Not applicable for the in-rush current to noise filter for less than 0.2ms.
(*5) Measure with JEITA RC-9131A probe, bandwidth of scope :100MHz.
(*6) 85 - 265VAC, constant load.
(*7) No load-Full load, constant input voltage.
(*8) Constant current limit and hiccup with automatic recovery. Not operate at over load or
dead short condition for more than 30 seconds.
(*9) OVP circuit will shutdown output, manual reset (re power on).
(*10) At 100/200VAC, nominal output voltage and maximum output current.
(*11) Measured by the each measuring method of UL, CSA, EN and DENAN (at 60Hz).
(*12) Ratings - Derating at standard mounting.
- Load (%) is percent of maximum output power or maximum output current, whichever is greater.
- As for other mountings, refer to derating curve.
- For conditions of start up at -40
(*13) Category 4 exposure levels : Track transportation over U.S. highways, composite two-wheeled trailer.
(*14) As for DENAN, dsigned to meet at 100VAC.
(Read instruction manual carefully, before using the power supply unit.)
MODEL
HWS50-3/HD HWS50-5/HD
(*3) V
(*3) Hz
0.98 / 0.90
(*2) 76 / 78 82 / 84
(*2) A 0.5 / 0.25
A
(*11) mA Less than 0.5. (0.2 (typ) at 100VAC / 0.4 (typ) at 230VAC)
VDC 3.3
(*1) A 0.1
A 10
W 33 50
(*6) mV 20
(*7) mV 40
120
160
(*10) ms
VDC 2.97 - 3.96 4.0 - 6.0
(*8) A >10.5
(*9) VDC 4.13 - 4.95 6.25 - 7.25
(*12)
RH
RH
(*13)
Designed to meet MIL-STD-810F 514.5 Category 4, 10
Designed to meet MIL-STD-810F 516.5 Procedure I, VI
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
More than 100M
Approved by UL60950-1, CSA C22.2 No.60950-1, EN60950-1, EN50178
(*14)
Designed to meet EN55011/EN55022-B, FCC-B, VCCI-B
Designed to meet IEC61000-4-2(Level 2,3), -3(Level 3), -4(Level 3),
g
mm
and no load. In that case, apply minimum output current.
to -10 , refer to derating curve.
HWS50-12/HD HWS50-15/HD
AC85 - 265 or DC120 - 370
47 - 63
0.99 / 0.95
81 / 83
0.7 / 0.35
14 / 28 Ta=25 , cold start
5 12 15
0.04
4.3 3.5
51.6 52.5
48 60
96 120
Less than 0.02% /
150
180
20
9.6 - 14.4 12.0 - 18.0
>4.51 >3.67
15.0 - 17.4 18.8 - 21.8
-
-
Possible
Designed to meet SEMI-F47 (200VAC Line only)
-10 to +71 (-10 to +50: 100%, +60: 60%, +71: 20%)
Guarantee start up at -40 to -10
-40 to +85
30 - 90 (No dewdrop)
10 - 95 (No dewdrop)
At no operating, 10 - 55Hz (sweep for 1min)
19.6m/s² constant, X, Y, Z 1hour each.
Less than 196.1m/s²
Convection cooling
Output - FG : 500VAC (100mA) for 1min
at 25 and 70%RH Output - FG : 500VDC
Designed to meet UL508, DENAN
Designed to meet IEC61000-3-2
-5(Level 3,4), -6(Level 3), -8(Level 4), -11
280
26.5 x 82 x 120 (Refer to outline drawing)
HWS50-24/HD HWS50-48/HD
82 / 84 83 / 85
24 48
0.02 0.01
2.2 1.1
52.8
96 192
192 384
200
240
19.2 - 28.8 38.4 - 52.8
>2.31 >1.15
30.0 - 34.8 55.2 - 64.8