Honeywell LYNXR Installation And Setup Manual page 19

Field 46: Enter up to 24 digits. Do not fill unused spaces. Enter 0-9, #+11 for '*'; #+12 for'#'; #+13 for a pause (2 seconds).
✻ "Follow Me Reminder" Phone Number
46
Enter up to 24 digits.
✻ Phone System Select
47
Note: For LYNXR/LYNXR24 only options 0, 1, 2, and 3
are applicable. For LYNXR-EN all options apply.
Central
Station
No WATS 0 = No
Speaker
Phone
WATS 2 = No
Speaker
Phone
Report Format for Primary/Secondary
✻
48
Primary
See choices below
0 = 3+1; 4+1 ADEMCO Low Speed Standard
1 = 3+1; 4+1 Radionics Standard
2 = 4+2 ADEMCO Low Speed Standard
3 = 4+2 Radionics Standard
5 = ADEMCO Contact ID® Reporting with 10-digit
subscriber account number
6 = 4+2 ADEMCO Express
7 = ADEMCO Contact ID® Reporting with
subscriber account number
8 = 3+1; 4+1 ADEMCO Low Speed Expanded
9 = 3+1; 4+1 Radionics Expanded
✻ Split/Dual Reporting
49
To Primary
0 = All reports
1 = Alarms, Restore, Cancel
2 = All except Open/Close, Test
3 = Alarms, Restore, Cancel
4 = All except Open/Close, Test
5 = All reports
To Primary
6 = All reports except Open/Close
7 = All reports
8 = All reports
9 = All reports except Open/Close
To Primary
10=All reports except Open/Close
11 = All reports
12=All reports
13=All reports except Open/Close
‡ Will report Users 0, 5-8, and, if using wireless button-type
devices, will report the zone number of the arm or disarm
button 26-33. All other zones and users are not reported.
WWW.DIYALARMFORUM.COM
Data Field Descriptions
Dialing Mode
Pulse Tone Pulse
1 = No 4 = With
Speaker Speaker
Phone Phone
3 = No 6 = With
Speaker Speaker
Phone Phone
Secondary
See choices below
4-digit
To Secondary
None, unless primary
fails, then all
Others
Open/Close, Test
All
All
All
To Paging Number
Alarms, Open/Close ‡ ,
Troubles
Alarms, Troubles
Alarms, Open/Close ‡ ,
Troubles
Open/Close ‡
To Follow Me System
Phone Number
Alarms, Open/Close ‡ ,
Troubles
Alarms, Troubles
Alarms, Open/Close ‡ ,
Troubles
Open/Close ‡
WWW.DIYALARMFORUM.COM
This option allows the user to schedule a time driven message. When
activated the system will dial the phone number programmed and deliver a
voice message (custom words 72, 73 and 74). This option is only supported
when the pager or follow me feature is enabled in field
10-13).
If using the Follow Me Reminder feature, enter the phone number here. If
fewer than 24 digits are entered, exit by pressing [
✻
the field press 46
The telephone message can be terminated (acknowledged) by pressing any
key on the telephone keypad. Pressing any key on the local LYNXR keypad
will terminate (acknowledge) both the follow me and the local reminder
announcements.
Note: The follow me reminder announcement will be terminated if any
other event requires the system to dial out or if and audible alarm
has occurred.
This option is used to enter the correct type of phone dialing (pulse or tone),
and to select the correct WATS line option for the Central Station. For
LYNXR-EN this option is used to activate the Speaker Phone option.
Note: If using pulse dialing, you must enter the numbers slowly in order to
Tone allow the pulse dialer time to operate.
5 = With
Speaker
Phone
7 = With
Speaker
Phone
✻
Enter as the 4th digit of
used. (For an explanation of these formats, see the System Communication
section of this manual.)
Notes: (1) The maximum number of alarm and alarm restore reports
during one armed period is determined by field
(2) If Option 5 is selected a 10-digit account number must be
entered in Fields
(3) Option 5 or 7 (ADEMCO Contact ID® Reporting) must be
selected for AVM.
This field is used to select a reporting option as follows:
Enter: 0 - 5 when reporting to telephone receivers.
6 - 9 when reporting to a pager is desired.
10 - 13 when reporting to an auxiliary telephone receiver.
Pager Report Format
Options 6-9 send reports to the primary phone number, in a format defined
✻
in Field 48, and send reports to a pager, which has its phone number
entered as the secondary phone number in Field
7-digit code, with optional 16-digit prefix, in the following format:
AAAAAAAAAAAAAAAA-EEE–00NN where:
AAA = Optional 16 digits for PIN number, etc. See Field
description of these characters.
EEE = 3-digit Event Code as follows:
911 = Alarm (NN = zone number)
101 = Open, system disarmed (NN = user no.)
102 = Close, system armed (NN = user no.)
811 = Trouble (NN = zone no.)
00 = Always displayed before 2-digit user/zone no.
NN = 2-digit user number or zone number, depending on the type of
event (EEE) that occurred.
Follow Me System Report Format
Options 10-13 send reports to the primary phone number, in a format
✻
defined in Field 48, and sends voice message to the secondary phone
number entered in Field
The message is a repeatable system status announcement. If the manual
paging option has been programmed in Field
"system, system.....".
The message can be terminated by pressing any key on the telephone
keypad.
–19–
✻
✻
.
✻ ✻
43 through 44, if 3+1 dialer reporting is to be
✻ ✻
43 or 44.
✻
42. The pager report is a
✻
42.
✻
87, the message will repeat
✻
49 (option 6-9 or
]. To clear entries from
✻
92.
✻
88 for full