Page 1 E-Series Routers Installation and User Guide Release 5.1.x Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, CA 94089 408-745-2000 www.juniper.net Part No. 162-00730-00 Rev. A00...
Page 2: Fcc Requirements For Consumer Products
JUNOS, SDX-300, and ServiceGuard software) or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,333,650, 6,359,479, and 6,406,312.
Page 3 Canadian Department Of Communications Radio Interference Regulations This Class B (or Class A, if so indicated on the registration label) digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regulations. Réglement sur le brouillage radioélectrique du ministère des communications Cet appareil numérique de la Classe B (ou Classe A, si ainsi indiqué...
Page 4: Ec Declaration Of Conformity
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord).
Page 5 Juniper Networks. This License will terminate immediately without notice from Juniper Networks if you breach any term or provision of this License. Upon such termination by Juniper Networks, you a. If you and Juniper Networks, Inc., have executed another license agreement for the Program which is now in effect, then such agreement (“Negotiated Agreement”) shall supersede this Software...
Page 6 Networks, its suppliers or its licensors of any warranties made under this License Agreement. In no event does Juniper Networks warrant that the Software is error free or that you will be able to operate the Software without problems or interruptions. Juniper Networks does not warrant: 1) that the functions contained in the software will meet your requirements;...
Page 7 This License Agreement shall be binding upon the parties and their respective successors and permitted assigns. Should you have any questions about this agreement, please contact: Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, CA 94089...
Page 9: Table Of Contents
Where E-Series Routers Fit In ........
Page 10 Contacting Juniper Networks ........
Page 11 Cabling the E-Series Router for Power ........
Page 12 Using HyperTerminal ..........8-2 Connecting Directly to the E-Series Router ......8-3 Assigning an IP Address .
Page 13 CT1 and CE1 I/O Modules ......... A-4 xiii E-Series Routers...
Page 14 Task 6: Configure Access to the Network Host ....B-5 Task 7: Enable the FTP Server on the E-Series Router ....B-6 Task 8: Identify the Files to Transfer .
Page 15: E-Series Routers
This E-Series Installation and User Guide provides the information you need to install and start the E-series router. Note: If the information in the latest E-series Release Notes differs from the information in this guide, follow the E-series Release Notes.
Page 16: Audience
About This Guide Audience This guide is intended for experienced system and network specialists working with E-series routers in an Internet access environment. Conventions Table 1 conventions used throughout the book, except for command syntax. Table 3 E-Series Command Reference Guide. For more information about...
Page 17: Documentation
Words enclosed in [ brackets ]* Words enclosed in { braces } Documentation The E-Series Installation Quick Start poster is shipped in the box with all new routers. This poster provides the basic procedures to help you get the router up and running quickly.
Page 18 E-Series Command Reference Guide A to M; E-Series Command Reference Guide N to Z – Together comprise the E-Series Command Reference Guide. Contain important information about commands implemented in the system software. Use to look up command descriptions, command syntax, a command’s related mode, or a...
Page 19: Mibs
Please e-mail your comments to: • techpubs-comments@juniper.net Along with your comments, be sure to indicate: • Document name • Document part number • Page number • Software release version Comments About the Documentation E-Series Routers E-Series System Basics Acronyms.
Page 20: Contacting Customer Support
About This Guide Contacting Customer Support For technical support, contact Juniper Networks at support@juniper.net, or at 1-888-314-JTAC (within the United States) or 408-745-9500 (from outside the United States).
Page 21: Part 1. Installing And Using E-Series Routers
Part 1 Installing and Using E-Series Routers...
Page 23: E-Series Overview
Network Management Tools Redundancy Features Overview E-series routers are modular, carrier-class networking devices that deliver performance, reliability, and service differentiation to both business and consumer Internet users. The ERX-7xx/14xx models offer high port density, low power consumption, and fully redundant Internet access routing and edge aggregation.
Page 24: Where E-Series Routers Fit In
Internet network. In customers are businesses using T1/T3 communication lines. In Figure DSL access multiplexer (DSLAM). Figure 1-1 E-series router communicating over T1/T3 lines Figure 1-2 E-series router communicating over DSL lines Figure 1-2 illustrate the location of E-series routers as an...
Page 25: E-Series Routers
POP location. The router is deployed by the service provider at the customer site as a CPE (customer premises equipment). Figure 1-3 ERX-310 router deployed in a small POP E-Series Routers Five models of E-series routers are available: • ERX-1440 router •...
Page 26: Erx-14Xx Models
CHAPTER 1 E-Series Overview ERX-14xx Models Note: In the E-series documentation, the term ERX-14xx models refers to both the ERX-1440 router and the ERX-1410 router. The terms ERX-1440 router and ERX-1410 router refer to the specific models. See The ERX-1440 router manages an extremely high volume of network traffic, and uses a 40-Gbps switch route processor (SRP) module, either the SRP-40G or SRP-40G+ module.
Page 27 E-Series Routers E-Series Routers Figure 1-4 ERX-14xx model, front view...
Page 28: Erx-7Xx Models
Figure 1-5 ERX-14xx model, rear view ERX-7xx Models Note: In the E-series documentation, the term ERX-7xx models refers to both the ERX-705 router and the ERX-710 router. The terms ERX-705 router and ERX-710 router refer to the specific models. See The ERX-7xx models are robust, high-density routers with less capacity than the ERX-14xx models.
Page 29 Note: The router may look different from the routers shown in the figures in this chapter, depending on the line modules in the slots. Figure 1-6 ERX-7xx model, front view Figure 1-7 ERX-7xx model, rear view E-Series Routers E-Series Routers Figure 1-6...
Page 30: Erx-310 Router
IP entry point into the network with the same IP-based protocols and services that are available on other E-series routers. The ERX-310 router is designed to be used as a small distributed POP router as well as a high-end CPE router.
Page 31 Figure 1-9 ERX-310 router, rear view (AC model) Figure 1-10 ERX-310 router, rear view (DC model) E-Series Routers E-Series Routers...
Page 32: E-Series Modules
1-10 CHAPTER 1 E-Series Overview E-Series Modules The system supports an SRP module and a selection of line modules. You can use any line module for access or uplink. Access line modules receive traffic from low-speed circuits, and the system routes the traffic onto higher-speed uplink line modules and then to the core of the network.
Page 33: Srp Module
E-Series Modules 1-11 E-Series Routers SRP Module Switch route processor (SRP) modules perform system management, routing table calculations and maintenance, forwarding table computations, statistics processing, configuration storage, and other control plane functions. Each SRP module is a PowerPC-based system with its own memory, nonvolatile disk storage, and power supply (see...
Page 34: Module Details
1-12 CHAPTER 1 E-Series Overview Figure 1-13 ERX-310 SRP module Module Details ERX-7xx/14xx models use up to two redundant SRP modules operating in an active/standby configuration. ERX-310 routers use only one SRP module. An SRP module must be present for any system to boot.
Page 35: Srp Module Redundancy
Module Details The SRP module provides standard craft management interfaces, including: • 10/100Base-T – Enables access to the E-series router for Ethernet management functions via CLI or SNMP, for example. • RS-232 – Provides a serial connection for monitoring the system’s hardware configuration through a PC (running terminal emulation software) or ASCII terminal.
Page 36: Line Modules
1-14 CHAPTER 1 E-Series Overview For details about installing the SRP I/O module, see Modules. Line Modules Line modules process data from different types of network connections. For information about available line modules and which SRP modules support specific line modules, see...
Page 37: Packet Classification
The system offers a complete SNMP interface for configuration, status, and alarm reporting. The system supports both Standard and Enterprise MIBs (Management Information Bases). The Juniper Networks E-Series Enterprise MIB is ASN.1 notated for easy importing into third-party SNMP management applications. For more information, see System Basics Configuration Guide, Chapter 3, Configuring Specifications.
Page 38: Nmc-Rx Device Management System
1-16 CHAPTER 1 E-Series Overview NMC-RX Device Management System The NMX-RX application provides a global method of managing all routers, line modules, and ports through a graphical user interface. Redundancy Features The system has the following redundancy features: SRP Modules Note: This section applies to ERX-7xx/14xx models only.
Page 39: Line Modules
I/O module associated with any failed line module in the redundancy group. The spare I/O module provides connectivity from the spare line module to the redundancy midplane. Specifications. In this scheme, an extra line module Redundancy Features 1-17 E-Series Routers...
Page 40 1-18 CHAPTER 1 E-Series Overview The process by which the system switches to the spare line module is called switchover. When switchover occurs, the system: Protocol processing then takes place on the spare line module. Figure 1-15 active. Figure 1-15 Data flow when a spare line module is active Breaks the connection between the primary I/O module and the primary line module.
Page 41: Power
ERX-7xx models, a –12 V, 15 W converter). If one converter fails, the other takes over. The ERX-310 router does not have redundant converters. For all E-series routers, the system software reports an alarm if any of the fans or converters fail. Modules. For information about configuring and...
Page 42 1-20 CHAPTER 1 E-Series Overview...
Page 43: Before You Begin
E-series routers. Topic Before You Begin Unpacking ERX-14xx Models Unpacking ERX-7xx Models and ERX-310 Routers Inspecting E-Series Router Components and Accessories If You Detect or Suspect Damage Contacting Juniper Networks The Next Step Before You Begin Before you begin unpacking the router, be sure you have the following tools: •...
Page 44: Unpacking Erx-14Xx Models
Juniper Networks recommends that you unpack the E-series router in the location where you want to install it. Heavy-Equipment Warning: Three people are required to install the E-series router in a rack: two to lift the system into position and one to screw it to the rack.
Page 45: Unpacking Erx-7Xx Models And Erx-310 Routers
ERX-7xx models and ERX-310 routers are shipped boxed, but not attached to a skid. For your convenience, Juniper Networks recommends that you unpack the E-series router in the location where you want to install it. To unpack an ERX-7xx model or an ERX-310 router: Open the carton from the top.
Page 46: The Next Step
• • To familiarize yourself with the electrical, environmental, and other guidelines and requirements for installing E-series routers, turn to Chapter 3, Installation Guidelines and If you are familiar with these guidelines and requirements, turn to Chapter 4, Installing E-Series Requirements.
Page 47: Installation Guidelines And Requirements
Installation Guidelines and Requirements This chapter reviews preinstallation considerations such as electrical, environmental, and safety compliances for E-series routers. For complete system specifications, refer to Topic Your Preinstallation Responsibilities Environmental Requirements Regulatory Compliances Safety Guidelines Equipment Rack Requirements Cabling Recommendations...
Page 48: Environmental Requirements
Be sure to allow enough space around the router for adequate ventilation. Inadequate ventilation can cause the system to overheat. Caution: Do not block the air vents on E-series routers. Otherwise, the router may overheat. Regulatory Compliances...
Page 49: Safety Guidelines
Heavy-Equipment Warning: Two people are required to lift an E-series router. Three people are required to install an E-series router in a rack. The equipment is extremely heavy. Ground (Earth) Warning: Connect the E-series router or rack to ground (earth), and ensure that a reliable grounding path is maintained in the rack.
Page 50: Power Cord Warnings (Ac Model)
In the United States, use Equipment, September Type of equipment racks recommended for E-series routers Number of equipment racks required to hold your current E-series router configuration Future expansion EIA-310-D Cabinets, Racks, Panels, and Associated...
Page 51 Equipment Rack Requirements E-Series Routers Figure 3-1 E-series routers installed in a rack...
Page 52: Mechanical Requirements
CHAPTER 3 Installation Guidelines and Requirements Mechanical Requirements Follow these mechanical requirements for your rack: • • • • • • Space Requirements If you use an enclosed rack for an ERX-14xx model, ensure that there is a minimum of 3 inches of clearance between the inner side wall and the router.
Page 53 Equipment Rack Requirements E-Series Routers Figure 3-2 Airflow for E-series routers...
Page 54: Cabling Recommendations
CHAPTER 3 Installation Guidelines and Requirements Cabling Recommendations You may want to consult the document Equipment Building System (NEBS) Requirements: Physical Protection, Issue 1, October 1995 Comply with the following recommendations: • • • • • • • • • for additional cable recommendations.
Page 55: Installing E-Series Routers
Installing E-Series Routers This chapter describes how to install E-series routers in a rack. Topic Before You Begin Freestanding Installation Rack-Mounted Installation The Next Step Before You Begin Before installing E-series routers, be sure you: • • • • Have a plan for installing E-series routers. This plan should consider future expansion of your system.
Page 56: Freestanding Installation
Chapter 11, System Warning: Two people are required to lift an E-series router. Note: All persons handling an E-series router should wear an antistatic device. Connectors are located on the I/O modules and the power input module and are installed from the rear of the router (see...
Page 57: Rack-Mounted Installation
Rack-Mounted Installation Juniper Networks recommends that you use a standard EIA distribution rack. Refer to Guidelines and Installation Guidelines Before installing the systems in a rack, consider the following guidelines and refer to • You can install up to three ERX-14xx models, six ERX-7xx models, or fourteen ERX-310 routers in a single 7-ft.
Page 58 CHAPTER 4 Installing E-Series Routers Figure 4-2 E-series routers installed in recommended order...
Page 59: Safety Guidelines
Branch Circuit Warning: Evaluate the overall loading of the branch circuit before you install any equipment into a rack. Ground (Earth) Warning: Connect the E-series router or rack to ground (earth), and ensure that a reliable grounding path is maintained in the rack.
Page 60: Installing The Router
• • Warning: Three people are required to install the E-series router in a rack: two to lift the system into position and one to screw it to the rack. Note: All persons handling an E-series router should wear an antistatic device.
Page 61: Installing Modules
Configuring Line Module Redundancy The Next Step Overview Line module slots are located in the front of each E-series chassis, while I/O module slots are located in the rear. See Overview, for front and rear views of E-series routers. In ERX-14xx models, modules mount vertically in a chassis with 14 slots.
Page 62: Slot Groups
CHAPTER 5 Installing Modules Figure 5-1 Orientation of line modules in E-series routers For details about available line modules, see Specifications. For information about compatibility between lines modules and SRP modules, see Specifications. Slot Groups The slots in the ERX-1410 router and the ERX-7xx models are divided into groups.
Page 63: Slot Groups For The Erx-1410 Router
Slot group 2 – slots 3 through 5 • Slot group 3 – slots 8 through 10 • Slot group 4 – slots 11 through 13 Slots 6 and 7 are reserved for the SRP modules. Figure 5-2 ERX-1410 slot groups Overview E-Series Routers...
Page 64: Slot Groups For The Erx-7Xx Models
OC48 Line Modules The ERX-1440 router with the SRP-40G+ SRP module supports OC48 line modules. Other E-series routers do not support OC48 line modules. An OC48 line module spans two slots in an ERX-1440 router. You can install this line module only in slots 2–3 and slots 4–5. Other slots in the system do not support this line module.
Page 65: Replacing And Managing Modules Using The Software
Protecting Modules and Slots Each E-series chassis has an ESD (electrostatic discharge) grounding jack. Table 5-1 discharge, connect an antistatic wrist strap to the jack when handling components.
Page 66: Order Of Installation
Caution: When handling modules, use an antistatic wrist strap connected to the E-series router’s ESD grounding jack. This action helps to protect the module from damage by electrostatic discharge. Caution: Always handle the module by its edges. Do not touch the components, pins, leads, or solder connections.
Page 67: Safety Guidelines
Lightning Activity Warning: Do not work on the system or connect or disconnect cables during lightning activity. DC Power Disconnection Warning: Before powering on the E-series router, remove power from the DC circuit by deactivating the circuit breaker on the panel board that services the DC circuit.
Page 68: Installing An Srp I/O Module
Slide the module into the chassis by placing it between the guides of the selected slot and pushing the module until it stops. Chapter 1, E-Series Tighten the module’s captive screws using a Phillips screwdriver. Turn both screws several times before tightening them completely to allow the module to sit correctly.
Page 69 Also, be sure that you have aligned the top and bottom edges in the correct matching tracks. Insert the module into the backplane by simultaneously depressing both ejectors (as shown in on the module. Installing SRP I/O and SRP Modules E-Series Routers Figure 5-5) and exerting forward pressure...
Page 70: Installing Line And I/O Modules
Installing a Line Module or an I/O Module To install a module: Note: Line modules are in the front of the system, and I/O modules are in the back of the system. Table 5-3 Module slot assignments E-Series Router ERX-1440 router ERX-1410 router ERX-7xx model ERX-310 router Tighten the module’s captive screws using a Phillips screwdriver.
Page 71: Removing A Module
Pull the ejector handles located at the top and bottom of the module so that they are in position 2, as shown in Figure 5-5) and exerting forward pressure E-Series System Basics Configuration Guide, Chapter 5, Removing a Module 5-11 E-Series Routers...
Page 72 5-12 CHAPTER 5 Installing Modules Figure 5-6 Ejectors in the closed position If you remove an I/O module and not the corresponding line module, the line module reboots. Its status becomes “inactive” when you issue the show version command. If you remove a line module and do not delete the corresponding configuration, the status of the line module will be “not present”...
Page 73: Installing Components For Line Module Redundancy
Warning: Do not insert any metal object, such as a screwdriver, or place your hand into an open slot or the backplane when the E-series router is on. Remove jewelry (including rings, necklaces, and watches) before working on equipment that is connected to power lines.
Page 74 5-14 CHAPTER 5 Installing Modules Warning: Turn off the E-series router before you install the redundancy midplane. Working inside the router when it is on can lead to electric shock and serious burns. Caution: A misaligned redundancy midplane can result in bent pins on the backplane and midplane and poor contact between the I/O modules and the redundancy midplane.
Page 75: Installing The I/O Modules
(See Module, earlier in this chapter.) Cable each module to provide a path to the remote interface (see Chapter 6, Cabling E-Series Installing Components for Line Module Redundancy E-Series Routers Installing a Line Module or an I/O Routers).
Page 76: Verifying The Installation
To verify that the installation is complete: Configuring Line Module Redundancy For information about configuring line module redundancy, refer to E-Series System Basics Configuration Guide, Chapter 5, Managing Line Modules and SRP The Next Step After you install the modules, you can connect cables to the system. Turn...
Page 77 Cabling E-Series Routers This chapter describes how to cable an E-series router. Before you cable the router, ensure that you have completed all installation instructions identified in previous chapters. Topic Cabling Overview Required Tools, Wires, and Cables Cabling the SRP I/O Module...
Page 78: Chapter 6 Cabling E-Series Routers
CHAPTER 6 Cabling E-Series Routers Note: Juniper Networks recommends that you use shielded cables where appropriate. Connect the power cables from the power source to the power input module. Connect the line I/O modules to their appropriate network interface.
Page 79: Cabling Overview
Cabling Overview E-Series Routers Figure 6-1 E-series ports and connectors (ERX-14xx model shown)
Page 80: Required Tools, Wires, And Cables
Direct connections to I/O modules Note: If you plan on using a cable-management bracket (ERX-7xx/14xx models only), install it before you begin cabling your E-series router. Cable-management brackets are helpful to keep network interface cables untangled and orderly and to prevent cables from hindering access to other slots.
Page 81: Cabling The Srp I/O Module
Cabling the SRP I/O Module Before powering up the E-series router, you must set up a management console. The console enables you to communicate with your system during the power-up process and to manage your system using the command line interface (CLI).
Page 82 CHAPTER 6 Cabling E-Series Routers • • Note: Use shielded cables to connect the external clock sources to the clock source input ports. Figure 6-2 ERX-14xx model SRP I/O module European – Two 75-ohm E1 2.048-Mbps inputs with BNC connectors North American –...
Page 83: Console Ports
A. Repeat steps 1 and 2 for the Clock B connections. Console Ports Note: This section applies to all E-series routers. There are two ports located in the Console section of the SRP I/O module (see •...
Page 84: Connecting To The Network
To connect the E-series router to the network: Connecting to a Console Terminal When you connect a console directly to the E-series router SRP I/O module, use a cable appropriate for your terminal connector. The cable must have a female DB-9 connector to attach to the RS-232 port on the SRP I/O module.
Page 85: Cabling The E-Series Router For Power
Connect the grounding wires to the chassis. Warning: Always connect the grounding wires first (before connecting the power cables) and disconnect them last when installing or servicing the E-series router. Connect the power cables (AC or DC) to the power input modules.
Page 86: Task 1: Turn Off All E-Series Router Power
Cabling E-Series Routers Figure 6-4 ERX-14xx model, power input module Task 1: Turn Off All E-Series Router Power Before starting, you must switch all E-series router power switches to OFF. • To turn off the router, push each power switch to the OFF position.
Page 87: Task 2: Connect The Grounding Cables
If applicable, loosen the screws from the clear power input module cover and remove it. Warning: Be sure the power source is turned off, the E-series router is turned off, and proper grounding wires are attached before continuing with this procedure.
Page 88 DC power source installed at your site. Color code standards for DC wiring do not exist. To ensure that the correct polarity is connected to the E-series router power units, confirm the connection of the power cables to the + (positive) and –...
Page 89: Router (Ac Model)
Note: To provide redundancy, Power A and Power B leads should not terminate at the same power source. Repeat steps 1–2 for the other power input module, if needed. Figure 6-6 ERX-310 router, rear view (AC model) Cabling the E-Series Router for Power E-Series Routers 6-13...
Page 90: Cabling I/O Modules
CHAPTER 6 Cabling E-Series Routers Cabling I/O Modules The following section illustrates the common connector types used with E-series I/O modules. For information about the connectors on the different line modules, see BNC Connectors Figure 6-7 I/O module with BNCs Chapter 12, Module Specifications.
Page 91: Hssi Connectors
Cabling I/O Modules 6-15 E-Series Routers HSSI Connectors The HSSI I/O module uses a standard 50-pin HSSI connector. Caution: Do not terminate HSSI connections with SCSI connectors. Although SCSI connectors look very similar to HSSI connectors, using SCSI connectors on HSSI connections may lead to data loss.
Page 92: Rj-45 Connectors
6-16 CHAPTER 6 Cabling E-Series Routers RJ-45 Connectors When inserting an RJ-45 connector, be sure it clicks into the port. Figure 6-9 I/O module with RJ-45 connector RJ-48C Connectors When inserting an RJ-48C connector, be sure it clicks into the port.
Page 93: Lc Duplex Connectors
Warning: IEC 825, Class 1 laser fiber connectors are for connection only to Class 1 laser devices. Figure 6-11 I/O module with LC full duplex connectors EN60825-1, Safety of Laser Products - Part 1: EN60825-1, Safety of Laser Products - Part 1: Cabling I/O Modules 6-17 E-Series Routers (2001), multimode (2001), single-mode...
Page 94: Sc Duplex Connectors
6-18 CHAPTER 6 Cabling E-Series Routers SC Duplex Connectors In accordance with Equipment Class, Requirements, and User’s Guide I/O modules with SC connectors are defined as follows: CLASS 1 LED PRODUCT. In accordance with Equipment Class, Requirements, and User’s Guide I/O modules with SC connectors are defined as follows: CLASS 1 LASER PRODUCT.
Page 95: Cabling X.21/V.35 Connectors
8 X.21 connectors or 8 V.35 connectors. The cable you attach to the port on the I/O module determines whether the connection is X.21 or V.35 and DCE or DTE. Figure 6-13 X.21/V.35 module with 50-pin X.21/V.35 connector Cabling I/O Modules 6-19 E-Series Routers...
Page 96: Redundant Ports
E-series module. Caution: For port redundancy to operate correctly on a GE I/O module that supports SFPs, both the primary and redundant ports on an E-series GE I/O module must use the same type of SFP. The Next Step Turn to for specifications.
Page 97: Before You Power Up The System
Powering Up E-Series Routers This chapter describes how to power up an E-series router and determine if it has booted properly. Topic Before You Power Up the System Powering Up Status LEDs Powering Down The Next Step Before You Power Up the System...
Page 98: Powering Up
Installation Task Warning: Be sure the power source is turned off and the system is turned off before performing the following task. Connect DC power or AC power to your E-series router. (depending on model) Cable all line modules. Powering Up Note: This procedure assumes that the system is already connected to a power source.
Page 99: Initialization Sequence
Initialization Sequence Each E-series line module is initialized independently. As a result, the CLI on the SRP module may become available before the line modules have completed initialization. Commands relating to a line module may fail if the module has not completed initialization. The show version command can be used to display line module status.
Page 100 CHAPTER 7 Powering Up E-Series Routers...
Page 101: Accessing E-Series Routers
Routers. The console allows you to communicate with the system during the power-up process, set an IP address, and manage the system using the command line interface (CLI). The E-series router can be managed and monitored through a: • •...
Page 102: Console Port Setup
CHAPTER 8 Accessing E-Series Routers to use the CLI to set an IP address on the system. Once you configure the IP address, you can access the system remotely (for example, via Telnet). Console Port Setup A console terminal (PC, Macintosh, or UNIX workstation) can be connected directly to the SRP I/O module via the RS-232 terminal port.
Page 103: Connecting Directly To The E-Series Router
Connecting Directly to the E-Series Router When you connect a console directly to the system, use a cable appropriate for your terminal connector. The cable must have a female DB-9 connector to attach to the RS-232 port on the system.
Page 104: Assigning An Ip Address
When you have configured an IP address for the system, you can run Telnet from a host to access the system through its Ethernet port. To connect the Ethernet port to the network: Chapter 7, Powering Up E-Series Enter the enable command at the User Exec prompt. host1>enable host1# The system is now in Privileged Exec mode.
Page 105 The system is now in Privileged Exec mode. Enter the configure command. host1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. host1(config)# Telnet Setup E-Series Routers E-Series System Basics Configuration for information on setting a password.
Page 106: Snmp
As an SNMP agent, the system provides access to management information that it maintains. See Guide, Chapter 3, Configuring SNMP E-Series Command Reference Guide A to M Reference Guide N to Z configuring the system as an SNMP agent. The Next Step...
Page 107: Maintaining E-Series Routers
Upgrading Memory on SRP Modules Replacing SFPs on GE I/O Modules Replacing Fan Trays Installing a Cable-Management Bracket on ERX-7xx Models Required Tools and Items You will need the following tools and other items to replace E-series components. • • •...
Page 108: Storing Modules And Components
Warning: Do not insert any metal object, such as a screwdriver, or place your hand into an open slot or the backplane when the E-series router is on. Remove jewelry (including rings, necklaces, and watches) before working on equipment that is connected to power lines.
Page 109: Upgrading Nvs Cards On Srp Modules
Warning: Do not insert any metal object, such as a screwdriver, or place your hand into an open slot or the backplane when the E-series router is on. Remove jewelry (including rings, necklaces, and watches) before working on equipment that is connected to power lines.
Page 110: Upgrading A System That Contains Two Srp Modules
Warning: Do not insert any metal object, such as a screwdriver, or place your hand into an open slot or the backplane when the E-series router is on. Remove jewelry (including rings, necklaces, and watches) before working on equipment that is connected to power lines.
Page 111: Replacing An Nvs Card
Push the new NVS card as far as you can in the slot. When you push the card far enough, it will click into place. Replace the faceplate on the NVS card slot. Upgrading NVS Cards on SRP Modules Components, earlier in this chapter). 9-1). E-Series Routers Figure 9-1).
Page 112: Upgrading Memory On Srp Modules
Warning: Do not insert any metal object, such as a screwdriver, or place your hand into an open slot or the backplane when the E-series router is on. Remove jewelry (including rings, necklaces, and watches) before working on equipment that is connected to power lines.
Page 113: Adding New Sodimms
Locate the four SODIMM sockets on the SRP module (see Figure 9-2 remove SODIMMs. Figure 9-2 SODIMM sockets on the SRP-5 and SRP-10 module Upgrading Memory on SRP Modules Figure 9-2). Figure 9-3). See the previous section to learn how to E-Series Routers...
Page 114: Verifying The Upgrade
CHAPTER 9 Maintaining E-Series Routers Figure 9-3 SODIMM sockets on the SRP-40 module Verifying the Upgrade To verify that the upgrade is complete: Insert a SODIMM from the upgrade kit at an angle of approximately 45 degrees into an empty ceramic connector, so that the notch in the long gold edge of the SODIMM aligns with the notch in the connector.
Page 115: Replacing Sfps On Ge I/O Modules
Warning: Do not insert any metal object, such as a screwdriver, or place your hand into an open slot or the backplane when the E-series router is on. Remove jewelry (including rings, necklaces, and watches) before working on equipment that is connected to power lines.
Page 116: Installing Sfps
Maintaining E-Series Routers Figure 9-4 Possible release mechanisms on the SFP Caution: For port redundancy to operate correctly, both the primary and redundant ports on an E-series GE I/O module must use the same type of SFP. Installing SFPs To install SFPs: Figure 9-5 Example of SFP Release the SFP and pull it out of the slot.
Page 117 4. Remove the dust cover that protects the ports. Connect the new cables to the SFP. If you are using the redundant port on the E-series GE I/O module, repeat steps through for the other port.
Page 118: Verifying The Installation
9-12 CHAPTER 9 Maintaining E-Series Routers Verifying the Installation When you have replaced the SFPs and connected the cables, issue the show interface gigabitEthernet command for each interface to check that the interface is operational (up). • • Field descriptions ›...
Page 119: Replacing Fan Trays
Caution: If the FAN FAIL LED on the SRP module is illuminated and none of the fans are spinning when you remove the fan tray, power down the system until a new fan tray is available. Operating an E-series router with inadequate air circulation may damage the modules.
Page 120: Removing The Fan Tray
9-14 CHAPTER 9 Maintaining E-Series Routers Figure 9-8 Fan tray in ERX-310 router Removing the Fan Tray To remove the fan tray: Warning: Do not place your fingers near the fans when removing the fan tray. The blades may still be moving.
Page 121: Installing The Fan Tray
Alternate between screws when tightening them to ensure that the electrical connectors at the back of the tray fit tightly. (ERX-14xx model only) Push the top bezel back on the front of the system. Figure 9-9 Fan tray in ERX-7xx model Replacing Fan Trays 9-15 E-Series Routers...
Page 122: Installing A Cable-Management Bracket On Erx-7Xx Models
9-16 CHAPTER 9 Maintaining E-Series Routers Installing a Cable-Management Bracket on ERX-7xx Models A cable-management bracket can be installed to accommodate cables of different sizes on ERX-7xx models. See • • Use two (2) #10 self-tapping screws to secure the bracket.
Page 123: Troubleshooting
Troubleshooting This chapter explains how you can troubleshoot a specific problem, such as abnormal LED activity or no system power, when you power up the router. Topic Diagnosing Problems Troubleshooting Power Failures Understanding Status LEDs to Troubleshoot Monitoring Temperatures of Modules Resetting Line Modules and SRP Modules Double-Bit Errors on SRP Modules Diagnosing Problems...
Page 124: Initialization Sequence
CHAPTER 10 Troubleshooting Initialization Sequence Each E-series line module is initialized independently. As a result, the CLI on the SRP module may become available before the line modules have completed initialization. Commands relating to a line module may fail if the module has not completed initialization. The show version command can be used to display line module status.
Page 125: Led Activity During Booting
Green Fan online Fan failure Green Ethernet link up Green Blinks when Ethernet traffic on link 10-3 E-Series Routers 10-4. ON to OFF Failure detected Diagnostic test running Module offine later in this chapter. Power off Power off Fan failure...
Page 126 10-4 CHAPTER 10 Troubleshooting Table 10-2 LED identification and activity descriptions (continued) LED Location LED Label Ethernet line LINK modules ACTIVITY HSSI line SYNC module YEL ALM RED ALM X.21/V.35 line ACTIVE module LOOPBK ERROR V.35 X.21 Other line SYNC modules YEL ALM RED ALM...
Page 127 SRP module. If the standby SRP module detects that the primary SRP module is not active, it reboots the system and takes control. (ERX-7xx/14xx models only) Understanding Status LEDs to Troubleshoot E-Series Routers 10-2) 10-3) 10-5...
Page 128 10-6 CHAPTER 10 Troubleshooting Figure 10-2 FE2 module LEDs Figure 10-3 E3 and T3 module LEDs...
Page 129: Led Activity During Booting
Actions 1 Check Power A and Power B terminal connections. 2 Verify that power switches are on. 3 Check connections to power sources. 4 If system still does not operate, contact Juniper Networks Customer Service. 10-7 E-Series Routers...
Page 130 3 If you replaced the line module or if there was a hardware failure, the system should automatically reset the module. 4 If condition persists, contact Juniper Networks Customer Service. Fan is not working Contact Juniper Networks Customer Service; the system properly or has slowed must be serviced.
Page 131: Redundancy Status
Module is booting or is an inactive primary line module. Module is active, but no standby module is available. Module is in standby state. Module is active, and a standby module is available. Monitoring Temperatures of Modules E-Series Routers 10-9...
Page 132: Resetting Line Modules And Srp Modules
The buttons work in the same way for the SRP module. Depressing the board reset button on an SRP module is equivalent to rebooting the E-series router and causes all the line modules to reboot. Double-Bit Errors on SRP Modules SRP modules include error checking and correction (ECC) to protect their SDRAM.
Page 133: Detecting Double-Bit Errors
SRP module after you reboot, or if the FAIL LED on the SRP module stays on during rebooting, the SDRAM is permanently damaged and needs replacing. In this event, call Juniper Networks Customer Service to arrange for repair. OCCURRED Address = 0xe95db10...
Page 134 10-12 CHAPTER 10 Troubleshooting...
Page 135: Part 2. System And Module Specifications
Part 2 System and Module Specifications...
Page 137: Chapter 11 System Specifications
System Specifications Topic ERX-14xx Models Specifications ERX-7xx Models Specifications ERX-310 Router Specifications ERX-14xx Models Specifications Table 11-1 ERX-14xx models specifications Category Weight Chassis only Chassis fully configured Dimensions Environmental Requirements Ambient operating temperature Ambient operating humidity Ambient storage temperature Ambient storage humidity Heat Dissipation Space Requirements Specification...
Page 138 11-2 CHAPTER 11 System Specifications Table 11-1 ERX-14xx models specifications (continued) Category Airflow DC Input Voltage Current Power Redundancy (input power) NEBS Certification Safety Agency Certification Electromagnetic Emissions Agency Certification Specification • An integral air plenum directs router’s exhaust air below the router and out the back.
Page 139: Erx-7Xx Models Specifications
Do not block air vents on sides of the router. • Do not place equipment that exhausts hot air to left on the right of the router. • Be aware that router exhausts hot air from its left side. ERX-7xx Models Specifications E-Series Routers ° ° 11-3...
Page 140 11-4 CHAPTER 11 System Specifications Table 11-2 ERX-7xx models specifications (continued) Category Airflow DC Input Voltage Current Power Redundancy (input power) NEBS Certification Safety Agency Certification Electromagnetic Emissions Agency Certification Specification • Airflow direction is in through the right side and out through the left side. See Figure 3-2 Chapter 3, Installation Guidelines and –40 to –72 VDC...
Page 141: Erx-310 Router Specifications
Long term: 5% to 85% (noncondensing) Short term: 5% to 95% (noncondensing) –40 ° to 158 ° F (–40 ° to +70 ° C), 95% relative humidity 5% to 95% (noncondensing) 500 W, 1706 BTU/hour maximum ERX-310 Router Specifications E-Series Routers ° ° 11-5...
Page 142 11-6 CHAPTER 11 System Specifications Table 11-3 ERX-310 router specifications (continued) Category Space Requirements Airflow DC Input Voltage Current Power Redundancy (input power) AC Input Power required AC line frequency Power NEBS Certification Safety Agency Certification Electromagnetic Emissions Agency Certification Specification •...
Page 143 CCITT recommendation G,703 interface at a rate of 2048 kbit/s with a 75 ohm unbalanced presentation, 1994 • RTTE Directive (1999/5/EEC) ERX-310 Router Specifications 11-7 E-Series Routers...
Page 144 11-8 CHAPTER 11 System Specifications...
Page 145: Chapter 12 Module Specifications
Module Specifications This chapter provides information about line modules, SRP modules, and I/O modules available for E-series routers. All line modules, with the exception of the IPSec Service and Tunnel Service module, combine with I/O modules to provide particular capabilities and connections.
Page 146 12-2 CHAPTER 12 Module Specifications...
Page 147 Module Functionality 12-3 E-Series Routers...
Page 148 12-4 CHAPTER 12 Module Specifications...
Page 149 Module Functionality 12-5 E-Series Routers...
Page 150 12-6 CHAPTER 12 Module Specifications...
Page 151 Module Functionality 12-7 E-Series Routers...
Page 152 12-8 CHAPTER 12 Module Specifications...
Page 153 Module Functionality 12-9 E-Series Routers...
Page 154 12-10 CHAPTER 12 Module Specifications...
Page 155 Module Functionality 12-11 E-Series Routers...
Page 156 12-12 CHAPTER 12 Module Specifications...
Page 157 F0 ASIC COCX-F3 ASIC Non-ASIC Non-ASIC CT3/T3-F0 ASIC E3 ATM Non-ASIC E3 FRAME Non-ASIC on the following pages for module details such as E-series Model SRP Module Compatibility Compatibility ERX-7xx models SRP-5G ERX-1410 router SRP-5G+ SRP-10G ERX-7xx models SRP-5G+...
Page 158 12-14 CHAPTER 12 Module Specifications Table 12-2 Module specifications (continued) Line Module or SRP Module Label Type FE-2 Non-ASIC GE/FE ASIC (128 MB) GE/FE ASIC (256 MB) HSSI-3F Non-ASIC IPSec Service ASIC OCx/STMx ATM ASIC OCx/STMx/DS3-ATM (128 MB) OCx/STMx/DS3-ATM ASIC (256 MB) OCx/STMx POS ASIC...
Page 159 Line module redundancy and SRP module redundancy are not supported on the ERX-310 router. b. Assembly is superseded by a newer assembly; however, assembly is supported by current software. c. See E-Series Physical Layer Configuration Guide, Chapter 9, Managing Tunnel Service and IPSec Service Interfaces. Model...
Page 160 12-16 CHAPTER 12 Module Specifications...
Page 161: I/O Module Specifications
I/O Module Specifications 12-17 E-Series Routers...
Page 162 12-18 CHAPTER 12 Module Specifications...
Page 163 I/O Module Specifications 12-19 E-Series Routers...
Page 164 12-20 CHAPTER 12 Module Specifications...
Page 165 I/O Module Specifications 12-21 E-Series Routers...
Page 166 12-22 CHAPTER 12 Module Specifications...
Page 167 I/O Module Specifications 12-23 E-Series Routers...
Page 168 12-24 CHAPTER 12 Module Specifications...
Page 169 I/O Module Specifications 12-25 E-Series Routers...
Page 170 12-26 CHAPTER 12 Module Specifications...
Page 171 I/O Module Specifications 12-27 E-Series Routers...
Page 172 12-28 CHAPTER 12 Module Specifications...
Page 173 I/O Module Specifications 12-29 E-Series Routers...
Page 174 12-30 CHAPTER 12 Module Specifications...
Page 175 I/O Module Specifications 12-31 E-Series Routers...
Page 176 12-32 CHAPTER 12 Module Specifications...
Page 177 I/O Module Specifications 12-33 E-Series Routers...
Page 178 12-34 CHAPTER 12 Module Specifications...
Page 179 I/O Module Specifications 12-35 E-Series Routers...
Page 180 12-36 CHAPTER 12 Module Specifications...
Page 181 I/O Module Specifications 12-37 E-Series Routers...
Page 182 12-38 CHAPTER 12 Module Specifications...
Page 183: Cable Lengths For X.21/V.35 Cables
Table 12-4 Maximum cable lengths for X.21/V.35 connections Transmission Speed (Hz) Table 12-4 shows the maximum cable lengths Cable Length Cable Length (Feet) 2400 4,100 4800 2,050 9600 1,025 19200 38400 56000 2048000 I/O Module Specifications E-Series Routers 1,250 12-39...
Page 184 12-40 CHAPTER 12 Module Specifications...
Page 185 Protocol Support This chapter lists the layer 2 and layer 3 protocols and applications that line modules and their corresponding I/O modules support. Modules are identified by their physical labels. See Specifications, for a list of modules and their identifying labels. Module Channelized OCx/STMx Modules Channelized T1 and E1 Modules...
Page 186: Chapter 13 Protocol Support
13-2 CHAPTER 13 Protocol Support Channelized OCx/STMx Modules Table 13-1 Channelized OCx/STMx modules Protocol or Application Acceptance of traffic for IP tunnels APS/MSP ATM (point-to-point) BERT Bridged Ethernet Bridged IP Cisco HDLC DHCP local server Dynamic interfaces F4 OAM (ATM Administration) FDL (facilities data link) Frame Relay IP Multicasting...
Page 187: Channelized T1 And E1 Modules
Dynamic interfaces F4 OAM (ATM Administration) FDL (facilities data link) Frame Relay IP Multicasting IPv6 Channelized T1 and E1 Modules E-Series Routers cOCx Line Module with cOCx Line Module with cOC12/STM4 FO I/O cOC3/STM1 Modules Modules (T3 layer) CT1 Line Module with...
Page 188: Channelized T3 Modules
13-4 CHAPTER 13 Protocol Support Table 13-2 Channelized T1 and E1 modules (continued) Protocol or Application IS-IS LAC Support – access side LAC Support – peer side LNS Support – Internet side LNS Support – peer side Local loopback MPLS Multilink Frame Relay Multilink PPP NBMA (multipoint ATM)
Page 189 Multilink PPP NBMA (multipoint ATM) OSPF Packet over SONET PPPoE Remote loopback SMDS (trunk encapsulation) Subscriber interfaces (static) Subscriber interfaces (dynamic) Channelized T3 Modules E-Series Routers CT3/T3-F0 Line Modules with CT3/T3 CT3/T3 I/O Modules 12 I/O Modules Yes (with AIS) 13-5...
Page 190: Ethernet Modules
13-6 CHAPTER 13 Protocol Support Table 13-3 Channelized T3 modules (continued) Protocol or Application Transparent bridging VRRP Ethernet Modules Table 13-4 Ethernet modules Protocol or Application Acceptance of traffic for IP tunnels APS/MSP BERT Bridged Ethernet Bridged IP Cisco HDLC DHCP local server Dynamic interfaces F4 OAM (ATM...
Page 191: Hssi Modules
Acceptance of traffic for IP tunnels APS/MSP BERT Bridged Ethernet Bridged IP FE-2 Line Module GE/FE Line with FE-2 I/O Module with FE-8 Modules I/O Modules HSSI-3F Line Modules with HSSI-3F I/O Modules HSSI Modules 13-7 E-Series Routers GE/FE Line Modules with GE I/O Modules...
Page 192 13-8 CHAPTER 13 Protocol Support Table 13-5 HSSI modules (continued) Protocol or Application Cisco HDLC DHCP local server Dynamic interfaces F4 OAM (ATM Administration) Frame Relay IP Multicasting IPv6 IS-IS LAC Support – access side LAC Support – peer side LNS Support –...
Page 193: Ocx/Stmx Atm Modules
LNS Support – peer side Local loopback MPLS Multilink Frame Relay Multilink PPP NBMA (multipoint ATM) OSPF OCx/STMx ATM Modules OCx/STMx ATM Line OCx/STMx ATM Line Modules with OC3-4 I/O Modules with OC12/STM4 Modules 13-9 E-Series Routers I/O Modules...
Page 194: Ocx/Stmx Pos And Oc48 Modules
13-10 CHAPTER 13 Protocol Support Table 13-6 OCx/STMx ATM modules (continued) OCx/STMx POS and OC48 Modules Table 13-7 OCx/STMx POS and OC48 modules OCx/STMx ATM Line Protocol or Modules with OC3-4 I/O Application Packet over SONET PPPoE Remote loopback SMDS (trunk encapsulation) Subscriber interfaces Yes (over bridged Ethernet...
Page 195 Management PPPoE Remote loopback SMDS (trunk encapsulation) Subscriber Yes (over POS) interfaces (static) OCx/STMx POS and OC48 Modules E-Series Routers OCx/STMx POS Line Modules with OC48 Line Module OC12/STM4 I/O with OC48 Frame Modules APS I/O Module Yes (over POS)
Page 196: Tunnel Service Modules
13-12 CHAPTER 13 Protocol Support Table 13-7 OCx/STMx POS and OC48 modules (continued) Tunnel Service Modules Table 13-8 Tunnel Service modules OCx/STMx POS Protocol or Line Modules with Application OC3-4 I/O Modules Subscriber interfaces (dynamic) Transparent bridging VRRP Protocol or Tunnel Service Line Application Module (TSM)
Page 197: Unchannelized E3 Modules
Tunnel Service Line Service Line Module (TSM) Module (SM) E3 ATM Line E3 FRAME Line Modules with E3 Modules with E3 I/O Modules I/O Modules 13-13 E-Series Routers IPSec Service Line Module COCX-F3 Line Modules with E3-12 FRAME I/O Modules...
Page 198 13-14 CHAPTER 13 Protocol Support Table 13-9 Unchannelized E3 modules (continued) E3 ATM Line Protocol or Modules with E3 Application I/O Modules APS/MSP (point-to-point) BERT Bridged Ethernet Bridged IP Yes (over bridged Ethernet) Cisco HDLC DHCP local server Dynamic interfaces F4 OAM (ATM Administration) Frame Relay...
Page 199: Unchannelized T3 Modules
T3 FRAME Line COCX-F3 Line Modules with Modules with CT3/T3 I/O CT3/T3 12 I/O Modules Modules Unchannelized T3 Modules E-Series Routers COCX-F3 Line E3 FRAME Line Modules with E3-12 Modules with E3 FRAME I/O I/O Modules Modules OCx/STMx ATM CT3/T3-F0 Line...
Page 200 13-16 CHAPTER 13 Protocol Support Table 13-10 Unchannelized T3 modules (continued) T3 ATM Line Modules with Protocol or CT3/T3 I/O Application Modules Bridged Ethernet Bridged IP Yes (over bridged Ethernet) Cisco HDLC DHCP local server Dynamic interfaces F4 OAM (ATM Administration) FDL (facilities data link)
Page 201: X.21/V.35 Modules
T3 FRAME Line COCX-F3 Line Modules with Modules with CT3/T3 I/O CT3/T3 12 I/O Modules Modules X.21/V.35 Modules E-Series Routers OCx/STMx ATM CT3/T3-F0 Line Line Modules with Modules with 4xDS3 ATM I/O CT3/T3 12 I/O Modules Modules Yes (over bridged...
Page 202 13-18 CHAPTER 13 Protocol Support Table 13-11 X.21/V.35 modules (continued) Protocol or Application Bridged IP Cisco HDLC DHCP local server Dynamic interfaces F4 OAM (ATM Administration) Frame Relay IP Multicasting IPv6 IS-IS LAC Support – access side LAC Support – peer side LNS Support –...
Page 203: Part 3
Part 3 Appendixes...
Page 205 Cable Pinouts This appendix lists the cables and connector pinout assignments for the cables used with the ERX-7xx models and ERX-14xx models. Topic SRP I/O Module CT1 and CE1 I/O Modules SRP I/O Module The SRP I/O module provides two management ports. You can connect a console directly to the RS-232 serial port using a shielded straight-through cable with a female DB-9 connector on one end and a male DB-25 with a crossover adapter on the DB-25 end.
Page 206: Appendix A Cable Pinouts
APPENDIX A Cable Pinouts Figure A-1 SRP I/O module serial port Table A-2 Table A-1 SRP I/O module – RS-232 serial connector pinout Once you have configured an IP address on the system, you can connect using a host running Telnet over the 10/100Base-T Ethernet port on the SRP I/O module.
Page 207: Srp I/O Module
• DB-9 female to RJ-45 female crossover null modem adapter • DB-9 female to RJ-45 female straight-through adapter Table A-3 lists the pinouts for the crossover adapter. SRP I/O Module E-Series Routers...
Page 208: Ct1 And Ce1 I/O Modules
APPENDIX A Cable Pinouts Table A-3 DB-9 – RJ-45 crossover adapter pinout DB-9 Pin a. n/c=no connect Table A-4 Table A-4 DB-9 – RJ-45 straight-through adapter pinout DB-9 Pin a. n/c=no connect CT1 and CE1 I/O Modules CT1 I/O modules have 24 RJ-48C female connectors. CE1 I/O modules have either 20 RJ-48C female connectors or two 25-pair female Telco connectors.
Page 209 20 pairs of BNC connectors. We supply the Telco cables if you purchase a balun panel. Figure A-4 connectors on a CE1 I/O module and the sequence of the pins in the connectors. CT1 and CE1 I/O Modules E-Series Routers shows the location of the Telco...
Page 210 APPENDIX A Cable Pinouts Figure A-4 CE1 I/O module with Telco connectors Figure A-5 balun panel. The cables from the CE1 I/O module are plugged into the two 50-pin Telco connectors on the other side of the panel. Figure A-5 Twenty-port balun panel Table A-6 cable.
Page 211 Port 12 RX TIP Port 12 TX TIP Port 13 RX TIP Port 13 TX TIP CT1 and CE1 I/O Modules E-Series Routers Signal Port 1 TX RING Port 2 RX RING Port 2 TX RING Port 3 RX RING...
Page 212 APPENDIX A Cable Pinouts Table A-7 Pinout of 50-pin Telco connector to ports 10–19 (continued) a. n/c=no connect Signal Port 14 RX TIP Port 14 TX TIP Port 15 RX TIP Port 15 TX TIP Port 16 RX TIP Port 16 TX TIP Port 17 RX TIP Port 17 TX TIP Port 18 RX TIP...
Page 213: Installing Junose Software
Systems That Are Operating with Two SRP Modules When installing new JUNOSe software, you must mount the software CD on a network host and transfer the release files to at least one E-series Installing Software When a Firewall . However, if the router contains two SRP modules, you...
Page 214: Identifying The Software Release File
FTP to transfer the software release files from the network host to the E-series router. In this case, you must configure the FTP server on the E-series router and ensure that FTP client software is installed on the network host.
Page 215: Task 1: Obtain The Required Information
Enable the FTP server on the E-series router. Identify the files to transfer. Transfer the files to the user space on the E-series router. Install the software release file to the system space on the E-series router. Save the current configuration.
Page 216: Task 3: Access Privileged Exec Mode
APPENDIX B Installing JUNOSe Software Task 3: Access Privileged Exec Mode To access this mode via the CLI: Task 4: Configure IP on an Interface Typically, you configure IP on the Fast Ethernet interface of the SRP module. To configure IP on an interface: Note: If an IP interface is not configured, you see the message “Invalid interface.”...
Page 217: Task 6: Configure Access To The Network Host
If the network host is listed, go to step 8. Otherwise, proceed with step 7. Add an entry to the Static Host Table so that the E-series router can access the network host. The host command allows you to specify the network host name and IP address.
Page 218: Task 7: Enable The Ftp Server On The E-Series Router
Task 9: Transfer Files to the User Space To transfer the files for the release to the E-series user space, use the FTP client software on the network host to connect to the FTP server on the E-series router.
Page 219: Task 11: Save The Current Configuration
Press <CTRL-Z> to return to Privileged Exec mode. Check that the E-series router is ready to boot with the new software release. host1#show boot If the old software version is still listed, verify that you completed the previous steps correctly.
Page 220: Installing Software When A Firewall Does Not Exist
Installing JUNOSe Software Installing Software When a Firewall Does Not Exist If there is no firewall between the E-series router and the network host on which you mount the software CD, you can transfer the software release files from the network host to the E-series router via the E-series FTP server or by issuing the copy command.
Page 221: Task 1: Obtain The Required Information
Exec mode on the E-series router • The IP address of the network host • The IP address of the E-series router • The IP address of the next hop to reach the destination network (for example, a gateway) •...
Page 222: Task 5: Configure Access To The Network Host
If the network host is listed, go to step 8. Otherwise, proceed with step 7. Add an entry to the Static Host Table so that the E-series router can access the network host. The host command allows you to specify...
Page 223: Task 6: Mount The Cd On The Network Host
Task 7: Copy the Software Release File To copy the software release file to the E-series router, use the copy command. Note: The destination file must have a .rel extension.
Page 224: Task 9: Reboot The System
Press <CTRL-Z> to return to Privileged Exec mode. Check that the E-series router is ready to boot with the new software release. host1#show boot If the old software version is still listed, verify that you completed the previous steps correctly.
Page 225: Installing Software In Boot Mode
Installing Software in Boot Mode To install the E-series software in Boot mode, you must access the CLI via the local console. To install the software: Obtain the required information for the installation. Divert network traffic to another router. Access the Boot mode.
Page 226: Task 4: Assign An Ip Address
CLI to the normal User Exec mode. Task 4: Assign an IP Address When you assign an IP address to the E-series router in Boot mode, the address is configured on the Fast Ethernet port of the primary SRP module.
Page 227: Task 8: Reboot The System
Copying Release Files from One E-Series Router to Another When you have copied the release files from a network host to one E-series router, you can transfer files from that E-series router to other E-series routers on the network. This feature is useful when: •...
Page 228: Upgrading Systems That Are Operating With Two Srp Modules
The procedures for transferring release files from a source E-series router to a destination E-series router are almost identical to transferring release files from a network host to an E-series router on the same side of the firewall. Note: You must enable the FTP server on the source E-series router.
Page 229 • If you are transferring the files from one E-series router to another, copy the file to the system space of the second E-series router from the user space of the first E-series router (see Release Files from One E-Series Router to appendix).
Page 230 B-18 APPENDIX B Installing JUNOSe Software...
Page 231: Customer Support
• • • Note: When requesting service via phone, e-mail, or the Web, please be sure to have your router serial number available. Your Juniper Networks support engineer will need this number to verify your support level. http://www.juniper.net/support/guidelines.html Case Manager: https://www.juniper.net/casemanager/cgi/mgr/welcome.htm...
Page 232: Information You Need To Supply
APPENDIX C Customer Support Information You Need to Supply When requesting technical support from the JTAC by phone, be prepared to provide the following information when prompted. For existing cases: • For new cases: • The JTAC engineer will also need the following information: •...
Page 233: Returning Products For Repair Or Replacement
E-Series Routers Returning Products for Repair or Replacement In the event of a hardware failure, please contact Juniper Networks to obtain a Return Material Authorization (RMA) number. This number is necessary to ensure proper tracking and handling of returned material at the factory.
Page 234 APPENDIX C Customer Support...
Page 235: Declaration Of Conformity
Product Name: Model Number(s): Product Options: Conforms to the following Product Specifications: Safety: EMC: Supplementary Information: Juniper Networks, Inc. Juniper Networks, Inc. 10 Technology Park Drive Westford, Massachusetts 01886 USA Edge Switching Router ERX-310, ERX-700, ERX-705, ERX-1400, ERX-1440 All Modules IEC 60950-1(2001-10) Ed.
Page 236 APPENDIX D Declaration of Conformity...
Page 237: Index
3-8, 6-1 FTP access. See FTP access IP address. See assigning an IP address management access 8-1 Telnet 8-4 connecting console to E-series router 8-3 connectors, pinouts A-1 console cables, SRP I/O modules 6-7 for management access 8-2 to 8-4...
Page 238 Declaration of Conformity, EC D-1 detecting double-bit error 10-11 Device Management System, NMC-RX 1-16 diagnosing problems. See troubleshooting diagnostic LEDs 10-2 dimensions of E-series router 11-1, 11-3, 11-5 dissipation, heat 11-1, 11-3, 11-5 distribution rack 3-4 documentation set, E-series xvii CD xvii...
Page 239 LEDs 10-2 line modules 1-10 normal activity 10-7 redundancy status 10-9 SRP modules 1-10, 10-5 lifting E-series router 2-2, 2-3, 4-5, 4-6 line build-outs 12-20, 12-21, 12-36, 12-37 line modules 1-14 to 1-15 access 1-10 allowed combinations 1-4 installing 5-10...
Page 240 ONLINE LED 10-3 order of module installation 5-6 packet classification 1-15 PCMCIA slot, SRP modules 1-13 performance rate, line modules 1-4 pinouts, E-series router cables and connectors A-1 planning site for installation 3-1 plenum 4-3 ports alarm 6-5 console 6-5...
Page 241 9-10 removing 9-9 storing 9-2 signal degradation, X.21/V.35 cables 12-39 site planning 3-1 size of E-series router 11-1, 11-3, 11-5 of rack 3-6 slot groups 5-2 ERX-1410 router 5-3 ERX-7xx models 5-4 overloading 10-8 small form-factor pluggable transceivers. See SFPs...
Page 242 SRP module B-1 systems with two SRP modules B-16 uplink line modules 1-10 ventilation. See airflow weight of E-series router 11-1, 11-3, 11-5 of rack 3-2, 3-6 X.21/V.35 cables 12-39 X.21/V.35 connectors, cabling 6-19 X.21/V.35 modules, protocols 13-17...

Juniper E-Series Installation And User Manual

Chapter 1 E-Series Overview

Chapter 2 Unpacking and Inspecting E-Series Routers

Chapter 3 Installation Guidelines and Requirements

Chapter 4 Installing E-Series Routers

Chapter 5 Installing Modules

Chapter 6 Cabling E-Series Routers

Chapter 7 Powering up E-Series Routers

Chapter 8 Accessing E-Series Routers

Chapter 9 Maintaining E-Series Routers

Chapter 10 Troubleshooting

Chapter 11 System Specifications

Chapter 12 Module Specifications

Chapter 13 Protocol Support

Appendix A Cable Pinouts

Appendix B Installing Junose Software

Appendix C Customer Support

Appendix D Declaration of Conformity

Quick Links

Troubleshooting

Related Manuals for Juniper E-Series

Summary of Contents for Juniper E-Series