The Camera Settings - TANDBERG Profile 42” Manual

Profile
Contents Introduction
Contents Introduction
Audio SoundsAndAlerts RingVolume:
Sets the ring tone volume[0-100] for an incoming call in steps of 0.5dB from -34.5dB to 15dB. Volume 0 =
Off.
Example:
Audio SoundsAndAlerts RingVolume: 50
Audio Volume:
<0..100>
Sets the volume level [0-100] on the loudspeaker output in steps of 0.5dB from -34.5dB to 15dB. Volume 0
= Off.
Example:
Audio Volume: 70

The Camera settings

Cameras Camera [1..7] Backlight:
Backlight is used to compensate for lights shining directly at the camera (usually the sun entering the
window) to avoid a too dark image from the room. Addresses the specific camera.
On: Set to On to turn on the backlight compensation.
Off: Set to Off to turn the backlight compensation off.
Example:
Cameras Camera 1 Backlight: Off
Cameras Camera [1..7] Brightness Level:
Define the Brightness Level for the camera. Requires the Brightness Mode to be set to manual. Addresses
the specific camera.
Range: 1-31
Example:
Cameras Camera 1 Brightness Level: 1
Cameras Camera [1..7] Brightness Mode:
Define whether to control the camera brightness manually or to have it automatically adjusted by the system.
Addresses the specific camera.
Auto: When set to Auto, the camera brightness is automatically set by the system.
Manual: Set to Manual to enable manual control of the camera brightness, e.g. the level of the brightness
level setting will be used for the camera.
Example:
Cameras Camera 1 Brightness Mode: Auto
D14324.03—AUGUST 2009
Getting started About the menus
Getting started About the menus
<0..100>
<On/Off>
<1..31>
<Auto/Manual>
The Settings menu The Settings library The Settings library
The settings menu Settings Library
Cameras Camera [1..7] Flip:
Applies to cameras which supports Flip mode. Enables the video on screen to be flipped upside down.
Addresses the specific camera. Since TANDBERG PrecisionHD 1080p camera auto-detects if the camera is
mounted upside down, the flip mode is not necessary to use for this camera.
On: When set to On the video on screen is flipped. This setting is used with cameras that can be mounted
upside down, but cannot auto detect that the camera is mounted upside down.
Off: Set to Off to display the video on screen the normal way.
Example:
Cameras Camera 1 Flip: Off
Cameras Camera [1..7] Focus Mode:
Determines whether the camera should be in auto focus or manual focus mode. Addresses the specific
camera.
Auto: When set to Auto the focus will be updated throughout the call. When moving the camera, the system
will use auto focus for a few seconds to set the right focus of the new camera position. After a few seconds
auto focus is turned off to prevent continuous focus adjustments of the camera.
Manual: If set to Manual the focus is adjusted manually.
Example:
Cameras Camera 1 Focus Mode: Auto
Cameras Camera [1..7] Gamma Level:
By setting the Gamma Level you can select which gamma correction table to use. This setting may be useful
in difficult lighting conditions, where changes to the the brightness setting does not provide satisfactory
results. Requires the Gamma Mode to be set to Manual. Addresses the specific camera.
Range: 0-7
Example:
Cameras Camera 1 Gamma Level: 0
Cameras Camera [1..7] Gamma Mode:
Applies to cameras which supports Gamma mode. The Gamma Mode setting enables for gamma
corrections. Gamma describes the nonlinear relationship between image pixels and monitor brightness.
Addresses the specific camera. The TANDBERG PrecisionHD 1080p camera do not need Gamma Mode.
The TANDBERG PrecisionHD 720p camera do support Gamma Mode.
Auto: Auto is the default and the recommended setting.
Manual: In severe light conditions, you may switch mode to manual and specify explicitly which gamma
table to use by setting the Gamma Level.
Example:
Cameras Camera 1 Gamma Mode: Auto
Cameras Camera [1..7] IrSensor:
The Camera IR setting determines whether the infrared receiver at the camera should be enabled or not.
The IR sensor LED is located in the front of the camera and flickers when the IR sensor is activated from the
remote control. Addresses the specific camera.
On: Set to On to enable the IR sensor on the camera.
Off: Set to Off to disable the IR sensor on the camera.
Example:
Cameras Camera 1 IrSensor: On
Administrator Guide
Cameras Appendices
Cameras Appendices
<On/Off>
<Auto/Manual>
<0..7>
<Auto/Manual>
<On/Off>
Contact us
Contact us
28