Table of Contents
Advertisement
4. Press and hold brakes, and press 1 or 2
on remote transmitter. (Button 1 for
mode one, and Button 2 for mode two)
(lights will flash once for mode 1 and twice
for mode 2)
After you have entered into one of the two
programming menus you can release the
brake pedal. The unit will stay in programming
mode until the hood pins-witch is pressed or
the valet switch has been turned off. (so take
your time to make the proper selection)
The menu will automatically start you at
function one, once you choose from one of the
three Options, you will automatically jump to
the next function.
To select one of the three options press the
appropriate transmitter button. (see below)
1. Channel 1 (LOCK) = Option 1
2. Channel 2 (START) = Option 2
3. Channel 3 (TRUNK) = Option 3
Once an option has been selected the parking
lights will flash 1,2 or 3 times. (Depending on
option selected)
CUSTOM OPTIONS
MODE 1 PROGRAMMING
Function 1: Ignition Lock, Door lock/unlock
Toggled, Dual Lock Pulses
•
Channel I*
•
Channel II
•
Channel III
Note: Secure lock adds a lock pulse 4
seconds after the module starts the engine
and also 4 seconds after it stops the engine.
Function 2: Must Select default setting.
•
Channel I*
•
Channel II
Function 3: Arming/disarming Chirp
•
Channel I*
•
Channel II
Function 4: Passive/Active Arming
•
Channel I*
•
Channel II
Function 5: Door Lock Pulse Time
•
Channel I*
•
Channel II
•
Channel III
Function 6: Siren / OEM Horn Mode
•
Channel I*
•
Channel II
•
Channel III OEM Horn Mode
Ignition Lock Enabled
Ignition Lock Disabled
Ignition Lock Disabled
&SecureLock enabled
Enabled
Enabled
Chirp Enabled
Chirp Disabled
Passive Arming
Active Arming
¾second Lock/Unlock
pulse
4 second
Lock/Unlock pulses
3/4second Lock pulse,
and two 1/4second
Unlock
pulses.
SirenMode Enabled
SirenMode Enabled
* = Factory Default
This conclude Mode 1 programming. To get a
playback of these options, press and release the
hood switch.
The programming of these four
functions (and those from Mode 2) will play back
in sequence via the parking lights.
CUSTOM ENGINE OPTIONS
MODE 2
This mode allows you to customize the
alarm/remote
starter's
cycles, engine run time and diesel engine
options.
Function 1: Engine Run Time
•
Channel I
•
Channel II*
•
Channel III
Function 2: Crank Cycles
•
Channel I
•
Channel II*
•
Channel III
Function 3: Crank Time
•
Channel I
•
Channel II*
•
Channel III
Function 4: Not Used
•
Channel II*
Function 5: Engine Type
•
Channel I
•
Channel II*
•
Channel III
* = Factory Default
This conclude Mode 2 programming.
Mode 1 for playback options.
TACH WATCH LOCKOUT
Tach Watch lockout is a safety feature built
into the remote starter to protect the
vehicle's starter motor. If, during remote
start, the vehicle's engine ever cranks the
entire programmed crank time without
detecting any tach pulses during the first
crank cycle, the unit will go into tach watch
lockout. The diagnostics for this is 3 quick
parking light flashes when trying to remote
start the vehicle.
If your module is in Tach Watch Lockout it is
indicating that a problem exists with the tach
signal it is receiving. Verify that the tach
wire from the remote starter is properly
connected to a good tach signal in the
vehicle.
To remove the unit from Tach Watch
Lockout you must do the following:
5
control
of
crank
5 minutes
15 minutes
25 minutes
2 max.
3 max.
4 max.
6 seconds max.
8 seconds max.
12 seconds max.
Disabled
Gasoline Engine
Gasoline Engine
Diesel Engine
See
Advertisement
Table of Contents
