Unit. This Unit must be installed by a certified technician using all safety devices supplied. Please note that this guide has been written for properly trained Autostart technicians: a certain level of skills and knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
Hood-Pin Switch. The PAB works only when the Hood is up. AS-1725 SH Installation Guide Inspect vehicle for any body damage or electrical problems Always solder and tape all connections.
Parking Light flashes to which the text refers throughout this manual refer to the Parking Light output of the unit, not of the vehicle. Description position only. CRANK IGNITION ON (RUN) positions. relay (Pin F) and extra Installation Guide AS-1725 SH...
Page 5
Connect this wire to the installed Hood Pin switch supplied. This (–) Hood Switch GREY input will disable or shut down the Remote Starter when the Hood is input This wire must be connected to the Brake Light wire of the vehicle.
+ 1 LOCK UNLOCK sec after release of the buttons. toggles (max. 30 sec.). LOCK UNLOCK ON / OFF toggles (max. 60 sec.). LOCK UNLOCK ON / OFF press of UNLOCK Installation Guide AS-1725 SH 250 ms). pulse, LOCK position.
Page 7
GREY (–) N/A This pin is not used. Leave it empty. AS-1725 SH Installation Guide , pressing will activate a 1- TRUNK PIN TRUNK output. If ground (-) is detected on the...
Page 8
Combustion Chamber before the vehicle is started. When a Remote Starter is installed on a diesel vehicle, the Glow-plug section of the Ignition circuit must be activated and allowed to operate before the vehicle is remote-started. For that purpose, the Glow-plug input wire of the Remote Car Starter must be connected to the Glow-plug indicator light of the vehicle.
Transmitter Programming b. Programming Options c. Honk/Horn Timing (if available) d. Tach Programming AS-1725 SH Installation Guide Description Note: Ensure that the voltage does not vary when the dimmer control switch is turned up or down. If this is the case, it is not the right wire.
Hood Pin switch in the Engine compartment. This will spare the installer the trouble of accessing the Hood Pin switch in the Engine compartment. for up to 20 seconds. position. IGNITION ON (RUN) position. Installation Guide AS-1725 SH...
Programming Centre will move from Function 1 to Function 2, then to Function 3, and so on. Therefore, whenever you access a particular Mode, be prepared to re-configure all the Functions of that Mode in ascending order. AS-1725 SH Installation Guide ) in step 2 of the LOCK UNLOCK for up to 20 seconds.
Tach signals produced by recent Ignition systems. There is no necessary manual adjustment. Nevertheless, a Tach-programming procedure must be carried out every time a new Remote Car Starter Unit is installed. This is because the Tach signals AS-1725 SH Installation Guide button is pressed for 3 sec. with Ignition TRUNK...
Press and hold the Brake Pedal, then simultaneously press the buttons on the Transmitter – the Horn will chirp 5 times. Release the Brake Pedal. To change the timing: P. 14 for up to 20 seconds. buttons on the Transmitter: LOCK UNLOCK UNLOCK Installation Guide AS-1725 SH START...
Most comebacks are the result of misunderstandings about how a product works or performs. Take the time to properly explain all functions and features to the customers before they leave the premises. Doing this will save time and money. AS-1725 SH Installation Guide button. LOCK button.
The unit will all Doors when the UNLOCK position. all Doors when the Brake Pedal LOCK position. IGNITION ON (RUN) all Doors when the key is UNLOCK IGNITION ON (RUN) Installation Guide AS-1725 SH wire of the position...
Note: Installation of the Starter Kill system requires an external relay. (Not included!) Passive or Active Arming The Remote Car Starter can be set to: AS-1725 SH Installation Guide signal, Secure Lock will START the Remote Car Starter will trigger an START once again 4 seconds after shut-down.
The system will play back the most recent event first, then the second one, and so on. If there is no event at all to report, the Parking Lights will give one long flash. P. 18 to disarm. UNLOCK IGNITION ON (RUN) Installation Guide AS-1725 SH button to LOCK position: you...
If the unit gives irregular signals (1 to 10 flashes followed by a pause, Irregular followed by further flashes), the system is playing back Start Failure Codes. This occurs when the Hood Pin-switch is pressed three times AS-1725 SH Installation Guide Description button under Safe Start. P. 19...
Page 20
Constant flashes Panic Mode is triggered. up to 30 sec. P. 20 Installation Guide AS-1725 SH...