Finishing; Front Panel Removal And Installation - Fujitsu 9319357003-02 Installation Manual

8. FINISHING

(1) Insulate between pipes.
• Insulate suction and discharge pipes separately.
• For rear, right, and bottom piping, overlap the connection pipe heat insulation and
indoor unit pipe heat insulation and bind them with vinyl tape so that there is no
gap.
• For left and left rear piping, butt the connection pipe heat insulation and indoor unit
pipe heat insulation together and bind them with and vinyl tape so that there is no
gap.
• For left and left rear piping, wrap the area which accommodates the rear piping
housing section with cloth tape.
• For left and left rear piping, bind the connection cable to the top of the pipe with
vinyl tape.
• For left and left rear piping, bundle the piping and drain hose together by wrapping
them with cloth tape over the range within which they fi t into the rear piping
housing section.
(2) Temporarily fasten the connection cable along the connection pipe with vinyl tape.
(Wrap to about 1/3 the width of the tape from the bottom of the pipe so that water
does not enter.)
(3) Fasten the connection pipe to the outside wall with a saddle, etc.
(4) Fill the gap between the outside wall pipe hole and the pipe with sealer so that rain
water and wind cannot blow in.
(5) Fasten the drain hose to the outside wall, etc.
Saddle*
Pipe
Connection pipe
(heat insulation)
Bind the pipes together
so that there is no gap.
Pipe
Drain hose
Seal A is used when the diameter
of gas pipe is Ø12.70 or more.
Butt connection pipe (heat
insulation) against the indoor
unit pipe (heat insulation) and
wrap with seal A so that there
is no gap.
Left piping
Connection cable
Pipe
Drain hose
Check the following:
GOOD
Drain hose
Saddle
En-7
Outside wall cap*
Sealer putty*
(Outdoors)
*Field supplied
Wall
Overlap the insulation
Indoor unit pipe
(heat insulation)
Vinyl tape
Wrap with cloth tape
Cloth tape
For connection from the left rear
Wall pipe Connection cable
Drain hose Connection pipe
NO GOOD NO GOOD NO GOOD
Lifted up Wave End in water

9. FRONT PANEL REMOVAL AND INSTALLATION

9.1. Intake grille removal
(1) Open the intake grille.
(2) While holding the intake grille, lift up the grille stay and secure the intake grille.
(3) Remove the screws from the arm-cover on the top part of the front panel
(in 2 places, one on the left and one on the right).
(4) Push down the arm-cover grips to release the lock.
(5) Open the intake grille until it is horizontal, and pull it towards you to remove it.
Intake grille
(1)
(3)
(4)
(2)
Grille stay
9.2. Intake grille installation
(1) Make the intake grille horizontal and push the attachment shafts into the holes for
them in the top of the front panel (in 2 places, one on the left and one on the right).
(2) While holding the intake grille, lift up the grille stay and secure the intake grille.
(3) Push the arm-cover grips up, and lock the intake grille attachment shaft.
(4) Fix the arm-cover on the top part of the front panel using screws (in 2 places, one on
the left and one on the right).
(5) Lift up the intake grille a little, and return the grille stay to its original position.
(6) Close the intake grille.
9.3. Front panel removal
(1) Remove intake grille. (Reference the intake grille removal.)
(2) Remove wire cover. (Remove the 1 screw.)
(3) Remove 4 screws.
Screws (4 position)
(4) The front panel is pulled to the front, raising the upper surface, and a front panel is
removed.
Intake grille
Grille stay
Arm-cover knob
Attachment shaft
Hole
Wire cover Screw (Wire cover)
Front panel