Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Fujitsu Inverter Halcyon
Summary of Contents for Fujitsu Inverter Halcyon
- Page 1 Compact Wall Mounted Type PART NO.9332280012-03...
-
Page 2: Table Of Contents
CONTENTS SAFETY PRECAUTIONS ........En-1 SWING OPERATION .......... En-11 FEATURES AND FUNCTIONS ......En-2 ECONOMY OPERATION ........En-11 NAME OF PARTS ..........En-3 MINIMUM HEAT OPERATION ......En-12 PREPARATION ............En-5 MANUAL AUTO OPERATION ......En-12 OPERATION ............En-6 CLEANING AND CARE ........En-13 TIMER OPERATION ..........En-8 TROUBLESHOOTING.........En-15 SLEEP TIMER OPERATION ........En-9 OPERATING TIPS ..........En-16 ADJUSTING THE DIRECTION OF... -
Page 3: Features And Functions
● Ensure that any electronic equipment is at least 3.3ft (1m) away from either the in- CAUTION! door or outdoor units. ● Avoid installing the air conditioner near a fi replace or other heating apparatus. ● When installing the indoor and outdoor unit, take precautions to prevent access to infants. ●... -
Page 4: Name Of Parts
NAME OF PARTS Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 To facilitate explanation, the accompanying illustra- tion has been drawn to show all possible indica- tors; in actual operation, however, the display will only show those indicators appropriate to the cur- rent operation. - Page 5 Fig. 1 Indoor Unit Fig. 5 Remote Controller 1 Operating Control Panel (Fig. 2) D Signal Transmitter 2 MANUAL AUTO button E MODE button ● When the MANUAL AUTO button is F MIN.HEAT button pressed in for more than 10 seconds, the forced cooling operation will start.
-
Page 6: Preparation
PREPARATION CAUTION! Turn on the Power ● Take care to prevent infants from acci- dentally swallowing batteries. Turn on the circuit breaker ● When not using the Remote Control- ler for an extended period, remove the Load Batteries (AAA/R03/LR03 × 2) batteries to avoid possible leakage and damage to the unit. -
Page 7: Operation
OPERATION To Select Mode Operation Press the START/STOP button (Fig.5 K ). The indoor unit’s OPERATION Indicator Lamp (green) (Fig. 3 5) will light. The air conditioner will start operating. Press the MODE button (Fig.5 E ) to select the desired mode. - Page 8 OPERATION To Stop Operation Press the START/STOP button (Fig. 5 K ). The OPERATION Indicator Lamp (green) (Fig. 3 5) will go out. About AUTO CHANGEOVER Operation ● When AUTO CHANGEOVER operation fi rst selected, the fan will oper- AUTO: ate at very low speed for about a few minutes, during which time the indoor unit detects the room conditions and selects the proper opera- tion mode.
-
Page 9: Timer Operation
TIMER OPERATION Before using the timer function, be sure that the Remote Controller is set to the correct current time (☞ P . 5). To Use the ON timer or OFF timer To Cancel the Timer Press the START/STOP button (Fig. 5 K ) Use the TIMER button to select “CANCEL ”... -
Page 10: Sleep Timer Operation
SLEEP TIMER OPERATION Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operation is stopped. To Use the SLEEP Timer To Cancel the Timer: While the air conditioner is operating or stopped, press the Use the TIMER MODE button to select SLEEP button (Fig. -
Page 11: Adjusting The Direction Of Air Circulation
ADJUSTING THE DIRECTION OF AIR CIRCULATION Vertical (up-down) direction of airfl ow is adjusted by pressing the Remote Controller's SET button. Horizontal (right-left) air- fl ow direction is adjusted manually, by moving the Airfl ow Direction Louvers. Whenever making horizontal airfl ow adjustments, start air conditioner operation and be sure that the vertical air direction louvers are stopped. -
Page 12: Swing Operation
SWING OPERATION Begin air conditioner operation before performing this procedure. To select SWING Operation Press the SWING button (Fig. 5 M ). The SWING Display (Fig. 6 Y ) will light. In this mode, the Airfl ow Direction Louvers will swing automatically to direct the airfl... -
Page 13: Minimum Heat Operation
MINIMUM HEAT OPERATION To use MINIMUM HEAT OPERATION Press the MIN. HEAT button (Fig.5 F ) While MINIMUM HEAT OPERATION The OPERATION indicator lamp (green) (Fig. 3 5 ) will go out, and the ECONOMY is in progress, only the following indicator lamp (green) (Fig. -
Page 14: Cleaning And Care
CLEANING AND CARE ● Before cleaning the indoor unit, be sure to turn it off and disconnect the Power Supply Cord. CAUTION! ● Be sure the Intake Grille (Fig. 1 8 ) is installed securely. ● When removing or replacing the air fi lters, be sure not to touch the heat exchanger, as person- al injury may result. - Page 15 CLEANING AND CARE Air Cleaning Filter Installation 3. Replace them by 2 new Air cleaning fi lters. 1. Open the Intake Grille and remove the Air 1 Remove the old air cleaning fi lters in reverse order fi lters. of their installation. 2 Install in the same way as for installation of the air 2.
-
Page 16: Troubleshooting
TROUBLESHOOTING In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the WARNING! electrical breaker and consult authorized service personnel. Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. -
Page 17: Operating Tips
TROUBLESHOOTING Symptom Items to check See Page ● Has the circuit breaker been turn off? CHECK ONCE Doesn’t operate at all: MORE ● Has there been a power failure? — ● Has a fuse blown out, or a circuit breaker been tripped? ●... -
Page 18: Auto Restart
OPERATING TIPS AUTO Restart In Event of Power Interruption ● The power supply to the air conditioner is stopped by a ● If a power interruption occurs during TIMER operation, the power interruption. The air conditioner will then restart timer will be reset and the indoor unit will begin (or stop) automatically in its previous mode when the power is operation at the new time setting.