Vertex Standard VXR-7000 Service Manual page 12

Operating Manual Reprint
Court Blip: Courtesy Blip
When this parameter is set to "on," this function causes
the VXR-7000 to send out a "blip" on the portable/mobile
radio is frequency each time the portable radio is unkeyed.
This provides audible confirmation to the user that the
VXR-7000 was able to receive the transmission from the
portable.
Press the [S ] bar to toggle "on" or "off."
PACE
Rev Bst: Reverse Burst.
When this parameter is set to "on," the CTCSS tone
signal's phase is inverted just before the repeater turns to
receive. This allows the portable/mobile station's CTCSS
Decoder to begin switching off, thus reducing the transi-
tion time required.
Press the [S ] bar to toggle "on" or "off."
PACE
DCS Typ: DCS Format
This command is effective only when DCS is chosen for
squelch control.
A = "Normal" DCS
B = "Inverted" (complement) DCS
Press the [S ] bar to select the desired DCS Type.
PACE
DDec Type: DCS Decoder Type
This command selects the manner in which DCS is to be
decoded.
Fixed = Decodes only the type selected in above pa-
rameter (DCS Typ: Normal or Inverted).
Auto = Both types (Normal and Inverted) will be de-
coded.
Press the [S ] bar to select the desired DCS Decoder
PACE
Mode.
Multi Tone: Enable/disable Multi Tone Operation
Press the [S ] bar to toggle Multi Tone Operation be-
PACE
tween selections "yes" and "no."
Press the [E ] key to
NTER
display the "M T
ULTI ONE
S " window, from
ELECT
which you may select a
CTCSS tone or DCS
code; move the cursol to
the appropriate field
you using the [A ] key, then press the [E
RROW
open the "T S " or "C
ONE ELECT
select the desired CTCSS tone or DCS code using the [A
] key, then press the [E
ROW
selected tone or code, or press the [E
You may set as many as 16 CTCSS tones and/or DCS
codes.
Note that, if you do not yet program a CTCSS tone or
DCS code in the "M
ULTI
the "M T S
ULTI ONE ELECT
grammed), press the [S
PACE
T S " window directly.
ONE ELECT
12
] key to
NTER
S " window. Now
ODE ELECT
] key again to accept the
NTER
] key to cancel.
SC
T S
" window (when
ONE ELECT
" window data is not pro-
] bar to display the "M
CWID ANI/ENI: Select the Identifier mode
Press the [S
PACE
"ANI/ENI," or "off." To select this feature to the "CW
ID" or "ANI/ENI," the "CW ID" parameter must be en-
abled via the dealer programming.
Action Mode: Select the repeater operation mode
Press the [S
PACE
tion or "Simplex" operation.
Tx Freq.: Edit Transmit Frequency
Use the [0] - [9] keys to enter the desired channel fre-
quency directly, and press the [E
CTCSS Encoders: Toggle CTCSS Encoder ON/OFF,
sets CTCSS Frequency
Press the [S
PACE
or "off," or press the [E
S
" window, from
E L E C T
which you may select a
CTCSS frequency using the
[A ] key; press [E
RROW
again to accept the selected
tone, or press the [E
to cancel.
DCS Encoders: Toggle DCS Encoder ON/OFF, sets DCS
Code #
Press the [S
PACE
"off," or press the [E
" window,
LECT
from which you
may select a DCS
code using the
[A ] key;
R R O W
press [E
N T E R
again to accept
the selected code, or press the [E
Base TOT: Enable/disable the Time-Out Timer while in
the "BASE" station mode
Press the [S
PACE
"yes" and no."
The TOT time is determined via dealer programming.
Base Guard: Enable/disable the Base Guard Feature
When this parameter is set to "yes," the transmitter will
be inhibited for a few seconds before the repeater (in the
-
R
"BASE" station mode) turns to receive.
The inhibit time is determined via dealer programming.
LOUT: Select the Lock Out Feature's mode
Press the [S
PACE
tween "BCLO," "BTLO," or "off," then press the [E
] key to accept the setting. "BCLO" inhibits transmit-
TER
ting while there is carrier present. "BTLO" inhibits trans-
ULTI
mitting while there is carrier present unless there also is a
valid tone present.
] bar to toggle the selections "CW ID,"
] bar to toggle between "Duplex" opera-
] key.
NTER
] bar to toggle the CTCSS Encoder "on"
] key to display the "T
NTER
]
NTER
] key
SC
] bar to toggle the DCS Encoder "on" or
] key to display the "C
NTER
]
] key to cancel.
SC
] bar to toggle the TOT feature selects
] bar to toggle the Lock Out Feature be-
ONE
S -
ODE E
-
N