Reset / Deleting Settings; Switching Between Modes 1, 2, 3 And; Mode 1 „6 V" (7.3 V / 0.8 A); Mode 2 „12 V" (14.4 V / 0.8 A) - ULTIMATE SPEED IAN 74798 Operation And Safety Notes

Operation
This avoids sparking, which often occurs when
connecting. The battery charger is controlled by an
internal MCU (Micro-Computer Unit).

reset / deleting settings

Q
After connection to the power supply, the appliance
automatically returns to its basic setting and remains
in STANDBY mode
Switching between modes 1,
Q
2, 3 and 4
P ress the MODE selection button
priate number of times.
The device switches between charging modes in
the following order: Standby , MODE 1
„6 V", MODE 2
and then repeats the cycle
nOTe: If a 12 V battery is connected, MODE 1 "6 V"
cannot be selected. If a 6 V battery is connected,
MODES 2, 3 and 4 "12 V" cannot be selected.
nOTe: If you press the selector button
mode automatically switches over to the next mode
and begins operation in that mode.
nOTe: However, if a battery is not disconnected
from the charging station after a full charge, the
appliance remains in trickle-charge mode, even if
the user switches over to another mode. This pro-
tects the battery from being damaged.
Mode 1 „6 V" (7.3 V / 0.8 A)
Q
This mode is suitable for charging 6 V lead-acid
batteries with a capacity less than 14 Ah.
P ress the selection button MODE
mode 1. After doing so, the corresponding lED
display „6 V" lights up. If you do not activate
2
an-other process afterwards, the electronic sys-
tem will automatically start the charging process
10 GB/IE/CY
the appro-
9
, MODE 3 , MODE 4
, charging
9
, to select
9
together with the lED display
current of) 0.8 A ± 10 %. If the procedure runs
without any problems, the lED display
remains on during the entire charging process, un-
til the battery is fully charged at 7.3 V / ± 0.25 V.
When the battery is fully charged, lED display
lights up and lED display
7
out. The device now switches automatically into
maintenance charging mode.
Mode 2 „12 V" (14.4 V / 0.8 A)
Q
This mode is suitable for charging 12 V lead-acid
batteries with a capacity less than 14 Ah.
P ress the selection button MODE
mode 2. After completion of this process, the
appropriate lED indicator
Then if you do not take any further action, the
electronic control and the lED indicator
automatically switches on and starts the charg-
ing process. If the procedure runs without any
problems, the lED display
during the entire charging process, until the
battery is fully charged. When the battery is
fully charged, lED display
lED display
8
switches automatically into maintenance charg-
ing mode.
Mode 3 „12 V" (14.4 V / 3.8 A)
Q
This mode is mainly suitable for charging 12 V
lead-acid batteries with a capacity greater than
14 Ah under normal conditions.
P ress the selection button MODE
mode 3. Then if you do not take any further ac-
tion, the electronic control and the lED indicator
switches on and starts the charging pro-
4
cess. If the process runs without any problems,
the lED indicator
whole charging process until the battery is
charged. When the battery is fully charged, the
lED indicator
7
at (with a
8
goes
8
, to activate
9
lights up.
3
remains on
8
lights up and
7
goes out. The device now
, to activate
9
remains on during the
8
and the die lED indicator
8
8