Table of Contents
Advertisement
Step 1: Make sure the LEIT-2ET controller is out in bright light to harness
light energy used to power the controller. It will take approximately thirty (30)
minutes, or less, in direct sunlight. Do not connect sensor wires at this time.
Wait until controller is charged and ready to be assigned an ID.
Step 2: Splice the two (2) yellow or yellow and black sensor wires together
using waterproof connectors. This splice will distinguish that the controller is
ready to communicate with a LEIT RC2ET handset.
Step 3: Connect via RADIO UPLINK screen:
a. On the LEIT RC2ET handset's MAIN MENU, press
UPLINK icon. Press
again, CONTROL ID: 00 DEFAULT SETUP with
the first Ø blinking appears. Press
screen appears with RADIO UPLINK icon selected. Press
connect, CONNECTED appears momentarily, then, CONTROL ID: 00, NO
DESCRIPTION screen appears. Press
DESCRIPTION appears with Ø blinking. At this point the user can assign a
new Controller ID.
b. To assign a Controller ID, press
the first digit. Press
and repeat the steps with the second digit (we
recommend changing the ID number to a number higher than 01).
Next, assign description, name or address (recommended). The default
is NO DESCRIPTION. Press
and the first letter of NO DESCRIPTION is
blinking. Press
or
and enter a letter for the first digit. Press
repeat the steps for each letter. After completion press
the new information with the new ID number and address. Use the new ID
number to connect to this controller and use the address or name to help
identify the controller location.
NOTE: Setting a new CLIENT ID (A-Z): The default ID is AAA (this is a security feature). If the
controller CLIENT ID is changed from AAA to other letters, the user must update the handset
to the same CLIENT ID after exiting the controller program.
and highlight RADIO
again to connect. ARE YOU SURE?
again to
again and CONTROL ID: 01, NO
or
and enter a number (1-9) for
and
to download
16
Repeat the steps to select a new ID. When finished, press
upload the new information. ARE YOU SURE? screen appears. Press
to download the information. UPDATE SUCCESSFUL message will appear
momentarily, confirming that the controller received the information and setup
is updated and complete. After the update is completed the CONTROLLER
MENU appears. The controller may now be programmed (section 4).
The user can now easily connect back to this controller using the newly
assigned CONTROL ID and CLIENT ID. Repeat the steps to program additional
controllers. Repeat the steps to program additional new controllers.
NOTE: When connecting to a LEIT-2ET controller, the controller CLIENT ID must be the same
10:00
as on the handset and controller.
ATTENTION: The two (2) yellow or yellow and black sensor wires are left connected, so the
RAIN OFF alert will not appear. If a rain sensor needs to be added, see Sensor Installation in
the LEIT-2ET controller instruction manual.
MAIN MENU
NOTE: Where multiple LEIT-2ET controllers are installed within range of the LEIT RC2ET, make
10:00
sure to assign different CONTROLLER ID numbers, one at a time.
4.
Controller Menu
After connecting to a LEIT-2ET controller, press
10:00
review the Controller ID and available controller information
until the CONTROLLER MENU appears. The CONTROLLER
CONNECTING
MENU screen is used to perform functions such as Manual
Run or Manual Test, set a program for each valve, activate
ET if a weather station is installed within range, check
History Reports, review Controller Status information, adjust
seasonal Budget, program Rain Delay, Wind Stop and Stop Irrigation for any
specific month of the year, as needed.
to connect and
10:00
10:00
CONTROL ID: 00
NO DESCRIPTION
RADIO UPLINK
RADIO UPLINK
10:00
10:00
CONNECTED
UPLOADING
CONTROL ID: XX
NO DESCRIPTION
CONNECT
CONNECTED TO
CONNECT
and
10:00
10:00
UPDATE
SUCCESSFUL
CONNECT
CONNECT
CONTROLLER MENU
17
again
10:00
ARE YOU
YES /
10:00
CONTROL
NO DESCR
CLIENT ID:
CONT. S
Advertisement
Table of Contents
