General Informations - Hameg HM 8131-2 Manual

General informations

Hersteller HAMEG GmbH
Manufacturer Industriestraße 6
Fabricant D-63533 Mainhausen
Die HAMEG GmbH bescheinigt die Konformität für das Produkt
The HAMEG GmbH herewith declares conformity of the product
HAMEG GmbH déclare la conformite du produit
Bezeichnung / Product name / Designation:
Frequenzgenerator/Function Generator/
Générateur de fonctions
HM 8131-2
Typ / Type / Type:
mit / with / avec: -
Optionen / Options / Options:
mit den folgenden Bestimmungen / with applicable regulations / avec les
directives suivantes
EMV Richtlinie 89/336/EWG ergänzt durch 91/263/EWG, 92/31/EWG
EMC Directive 89/336/EEC amended by 91/263/EWG, 92/31/EEC
Directive EMC 89/336/CEE amendée par 91/263/EWG, 92/31/CEE
Niederspannungsrichtlinie 73/23/EWG ergänzt durch 93/68/EWG
Low-Voltage Equipment Directive 73/23/EEC amended by 93/68/EEC
Directive des equipements basse tension 73/23/CEE amendée par 93/68/CEE
Notes regarding the Declaration of Conformity
HAMEG measuring instruments comply with the EMC directive. Our conformity tests are based upon the relevant standards. In
case there is a choice of test limits HAMEG will test to the most stringent ones. Radiated emission tests are based upon the
limits (class 1B) for Small Business. Immunity tests are based upon the limits applicable for industrial sites.
All input and output cables influence emissions as well as immunity and may cause a violation of standards' limits if improperly
installed. The following hints will help to preclude any problems:
1. Interface connections
All connections between measuring instruments and external printers, computers etc. must be shielded. Unless the operating
instructions do not specify a shorther length a maximum of 3 m must not be exceeded for input/output or signal/control cables.
Also, such cables must not be run external to the building. In case several cables can be connected to an interface terminal only
one may be connected at any time. Interface cables should be of a double-shielded type. Suitable cables for the IEEE bus are the
types HZ72S and HZ72L.
2. Signal connnections
All connections between the measuring instrument and the unit under test should be kept as short as possible. Unless the
operating instructions do not specify a shorter length 3 m must not be exceeded. Also, such cables must not be run external to
the building. All signal connections must use shielded coax such as RG58/U. Proper ground connection is mandatory. Signal
generator output cables should be of the double-shielded type, e.g. RG223/U, RG214/U.
3. Immunity
Strong magnetic or electric fields may introduce undesired signals into the measuring instrument even if the measuring setup
was carefully chosen. HAMEG instruments will not be destroyed in such case. In rare cases such influences may cause minor
measurement errors, however, with results outside of specifications.
44
KONFORMITÄTSERKLÄRUNG
DECLARATION OF CONFORMITY
DECLARATION DE CONFORMITE
HO88-2/HO89-2
Angewendete harmonisierte Normen / Harmonized standards applied / Normes
harmonisées utilisées
Sicherheit / Safety / Sécurité
EN 61010-1: 1993 / IEC (CEI) 1010-1: 1990 A 1: 1992 / VDE 0411: 1994
Überspannungskategorie / Overvoltage category / Catégorie de surtension: II
Verschmutzungsgrad / Degree of pollution / Degré de pollution: 2
Elektromagnetische Verträglichkeit / Electromagnetic compatibility / Compatibilité
électromagnétique
EN 61326-1/A1
Störaussendung / Radiation / Emission: Tabelle / table / tableau 4, Klasse / Class /
Classe B.
Störfestigkeit / Immunity / Imunitee: Tabelle / table / tableau A1.
EN 61000-3-2/A14
Oberschwingungsströme / Harmonic current emissions / Émissions de courant
harmonique: Klasse / Class / Classe D.
EN 61000-3-3
Spannungsschwankungen u. Flicker / Voltage fluctuations and flicker / Fluctuations
de tension et du flicker.
Datum/Date/Date
15.01.2001
Instruments
Unterschrift / Signature /Signatur
E. Baumgartner
Technical Manager
Directeur Technique
HAMEG GmbH
Subject to change without notice
®