Table of Contents
Advertisement
ups. The
f&owing
example
will program.
store,
recalland in-
spect three different
relay set ups a\\ of which
are in the
matrix
mode. Programs 4, 5 end 43 will be used throughout
the exampie,
I.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
53.
14.
15.
16.
17.
18.
19.
20.
21.
Press RESET. Reset the Model 706.
Press PRGM, 9, 3. Activates
the inspect mode and
displays the following for approximately 0.5s~.
I InsPEEtl
,
J
After the inspect display, the Model 706 reverts to the
previously displayed channel or crosspoint with the blink-
ing decimal point.
Press PRGM, 6, 0, ENTER. Activates matrix mode.
Press 0, 0, I, 1, CLOSE. Closes crosspoint 003 1 c.
Press 0, 0, 2, 2, CLOSE. Closes crosspoint 002 2 c.
Press 0, 0, 3, 3, CLOSE. Closes crosspoint 003 3 c.
Press PRGM, 4,O, 1, ENTER. Stores the present relay set
up in location 01.
Press RESET. Resets Model 706.
Press 0, 0, 1, 2, CLOSE. Closes crosspoint 001 2 G.
Press 0, 0, 2, 3, CLOSE. Closes crosspoint 002 3 c.
Press 0, 0, 3, 4,
CLOSE. Closes
crosspoint 003 4 c.
Press PRGM, 4,0, 2, ENTER. Stores the
present
relay set
up in location 02.
Press RESET. Resets
the Mode) 706.
Press 0, 0, 1,3,
CLOSE.
Closes crosspoint 001 3 c.
Press 0, 0, 2, 4, CLOSE. Closes crosspoint 002 4 c.
Press 0, 0, 3, 1, CLOSE. Closes crosspoint 003 1 c.
Press PRGM, 4,0,3,
ENTER. Stores the present relay set
up
in [ocation 03.
Press RESET. Resets the Model 706.
Press PRGM, 5, 0, 1, ENTER. Recalls relay set up 01.
Ptess CHANNEL, CHANNEL,
CHANNEL.
Pressing tie
CHANNEL button while
in
the inspect
mode advances
the
display to the next closed crosspoint. When the last
closed crosspoint of a set up is reached pressing
CHAN-
NEL displays the first closed crosspoint of the set up.
Press RESET. Resets Model 706.
22. Press PRGM, 5,0, 2, ENTER. Recalls relay set up 02.
23. Press CHANNEL,
CHANNEL, CHANNEL,
CHANNEL.
Displays all the closed crosspoints of relay setup 02. Then
displays first closed crosspoint.
24. Press RESET. Resets
Model 706.
25. Press PRGM, 5, 0, 3, ENTER. Recalls relay set up 03.
26. Press CHANNEL,
CHANNEL,
CHANNEL,
CHANNEL.
Advanced to and displays all the closed crosspoints of
relay set up 03. Then loops back to the first closed cross-
point.
27.
Press
PRGM, 9, 3. Takes the Model 706 out of the in-
spect mode
and displays get
out for H sec.
I
LCW.
.
28. Press
CHANNEL,
CHANNEL,
CHANNEL.
This
step
shows that when the Model 706
is
out of the inspect
mode, pressing
CHANNEL
advances
the display to the
next
channel whether it is
open
or
closed.
White in the in-
spect mode pressing CHANNEL advances the display
to the next closed crosspoint.
NOTE
Program
93 may
also
be
used
in
the
normal
mode (out of matrix). In the normal mode the
closed channels are displayed.
NOTE
fn ihe inspect mode, pressing CHANNEL ad-
vances and displays the next closed channel or
crosspoint.
The crosspoint or channef is NOT
CLOSED, it is just displayed for the user's in-
spection.
The preceding example has shown how to:
1. Activate Program 93 inspect mode {step 21.
2. Activate matrix mode Istep 31.
3. Program three relay set ups and store them using Program
4. (steps 4.171.
4.
Recall the stored relay
set
ups (steps 19, 22 and 251.
5.
Inspect
the closed crosspoints of the set up (steps 20, 23
and 261.
6. Take the Model 706 out of the inspect mode (step 271.
NOTE
Activating
Program 99 or shutting off power to
the
Model
706 takes the instrument out of the
inspect mode.
2.9.14 Program
94 Clear
Program
94 is used to clear a
buffer location. A buffer
loca-
tion consists of
a
relay set up that was stored using Program
4. Up to 75 relay set ups can be stored and individually
cleared of data using Program 94. Use the following example
to:
rStore five relay set ups in location 1 thru 5.
aClear locations 3, 4 and 5 using Program 94.
1. Press PRGM , 4, 0, 1, ENTER. Selects Program
4 and
stores the present relay set up in location
01.
For simplici-
ty in this procedure the relay set up is all relays open.
2. Press PRGM, 4, 0, 2, ENTER. Seiects Program 4 and
stores
the present relay set up
in
location 02. For simplici-
ty in this procedure the relay set up is all
relays
open.
3.
Press
PRGM,
4,
0, 3, ENTER. Selects Program 4 and
stores the present relay set up in location 03. For simplici-
ty in this procedure the relay set up is all &ys
open.
4.
Press
PRGM
4, 0, 4, ENTER. Selects Program 4 and
stores the present relay set up in location 04. For simplici-
ty in this procedure the relay set up is all relays open.
_
2-27
Advertisement
Table of Contents
