12"xga/15" xga/17" sxga/19" sxva industrial monitor with resistive touch screen, vga, dp or hdmi display port, and dc24 v input (30 pages)
Summary of Contents for Advantech FPM-3155 Series
Page 1
FPM-3155 Series Industrial Flat Panel Monitor with 15" LCD VGA/Video Users Manual...
Page 2
Copyright This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Spec- ifications are thus subject to change without notice.
Page 3
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence when the equipment is operated in a residential environment.
If any of these items is missing or damaged, contact your distributor or sales representative immediately. Additional Information and Assistance 1.Visit the Advantech web site at www.advantech.com where you can find the latest information about the product. 2.Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equip- ment and must be easily accessible.
Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung.
Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3155 Series is a 15" color TFT LCD flat panel monitor built specifically for industrial applications. With the optional touch- screen, the FPM-3155 Series is an excellent and user-friendly system control interface. In addition to its usual application as an LCD panel monitor, the FPM-...
• Dimensions: (W x H x D):428 x 310 x 84 mm (16.9" x 12.2" x 3.3") • Weight:7 Kgs (15.4 lbs) • CE, FCC, BSMI, CCIB compliant Touchscreen (Optional) • Type: 8 wire, analog resistive • Resolution: continuous • Light transmission: 72% •...
1.4 Connectors The following connectors are situated on the left hand side of the FPM-3155 Series: VGA Port (DB-15) This DB-15 connector can be connected to the system via the external 15- pin DB-15 connector located on the left side of the system unit.
Chapter 2 System Setup 2.1 Mounting the Monitor The FPM-3155 Series can be placed as you require. The versatility of the FPM-3155 mounts enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting With wall brackets, the FPM-3155 can be mounted directly to a wall.
2.1.2 Panel Mounting If you need to install the FPM-3155 series on a panel mount, please release the mounting brackets by detaching four screws on rear side and fix them on up and bottom side by screws. Figure 2-2: Panel Mounting (cut out dimensions: 396 x 296 mm)
2.1.3 Rack Mounting To install the FPM-3155 on a 19" rack, you need rack mount kit FPM- 3150Rack-MT (4 bracket pieces). Assemble the rack mount brackets with 12 screws, then affix the monitor on the rack. Figure 2-3: Rack Mounting FPM-3155 Users Manual...
2.2 Desktop, Swingarm mounting The FPM-3155 Series can be mounted in other ways. You can place the desktop stand for desktop use or attach it on a swing-arm bracket. 2.2.1 Desktop Stand The desktop stand bracket is attached to the rear of the FPM-3155. Sim- ply detach the small bracket at the top of the monitor by unscrewing the two screws.
2.2.2 Swing-ARM Detach the mounting brackets on the rear side, then attach the FPM-3155 series onto the Swing-ARM mount (75mm or 100mm square bracket). Figure 2.5: Swing-ARM for the FPM-3155 series FPM-3155 Users Manual...
Appendix A Touchscreen Driver Installation A.1 Introduction The FPM-3155 Series’ optional touchscreen uses an advanced 8-wire resistive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments, and has been approved to FCC Class A and Class B standards.
• Storage temperature: -25 ~ 70° C (humidity 20 ~ 95% RH) A.3 Installation of Touchscreen Driver The touchscreen for the FPM-3155 Series provides drivers for use with MS-DOS, Windows 3.1, 95, 98, NT, and 2000. For the detailed touch- screen driver installation procedure, please refer to the “TSCB-9516...
Appendix C OSD Operation C.1 OSD Operation Keypad The OSD keypad, including six keys and a two color indicator, is designed as the OSD operation interface. The six keypad functions are in Table C-1. Auto Press this button to execute auto adjustment process Press to show the OSD screen or select an item to change its setting !"#...
C-2 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out.
Page 30
Digital Color Controls- Press the "# key to adjust the digital controls such as black level, red/green/blue gain, hue & saturation, flesh-tone compensation and color. Analog Settings- Press the "# key to adjust controls such as brightness, contrast, Horizontal and vertical position, phase, clocks per line and auto con- figuration.
Page 31
Clocks- Press the !"and"# keys to adjust the number of clocks per line in the analog to digital converter. Auto Config- Press the # key to automatically configure the above settings. OSD-Timeout- Press the !"and"# keys to decrease or increase the amount of time that elapses before the menu disappears.
Page 32
Red Gain- Press the !"and"# keys to adjust the red gain. Green Gain- Press the !"and"# keys to adjust the green gain. Blue Gain- Press the !"and"# keys to adjust the blue gain. Firmware version- This monitor uses software version X.XX Overlapped Modes- Press the !"and"# keys to tell the monitor to use DOS mode timings (720 pxl/line) or EGA/CGA timing (640 pxl/line) when these modes are otherwise indistinguishable.