Quick Guide To The Special Functions - Electrolux Diva Service Manual

15 QUICK GUIDE TO THE SPECIAL FUNCTIONS

The table below briefly describes how each of the special functions available to the user and to the Service Engineer can be used. The display does not indicate any
function neither of Service nor User.
Function Activation of the function
Buttons
S0
(On/Off)
Select
regeneration
[S2 + S3]
S0
(On/Off)
Deactivate
rinse-aid
[S2 + S3]
Accessing
diagnostics
[S1 + S3]
mode, alarm
display and
S0
(On/Off)
activation of
actuators
[S1 + S3]
Cancel alarms
stored in
memory
S0
(On/Off)
[S1 + S3]
Test cycle
S0
(On/Off)
[S1 + S3]
Extra rinse
S0
(On/Off)
[S1 + S3]
Disable buttons
S0
(On/Off)
In order to memorize the functions or exit diagnostics mode, press key S0 to switch the appliance off. In most cases, memorization / exit take place automatically
Exit / Memorize
after 60 seconds (in which case the appliance returns to pre-selection mode).
(*) To activate the functions available to the user, no cycles must be selected: to cancel them see 4.3.1 (i.e. the appliance must be in pre-selection mode).
SOI/TD PR
Starting the function
Led(s) Buttons
LD1 + LD2+ LD3
S1
flash
LD1 + LD2+ LD3
S2
flash
LD1 + LD2 + LD3
S1
flash
LD1 + LD2 + LD3
S2
flash
LD1 + LD2 + LD3
S3
flash
[S1 + S2]
LD1 + LD2 + LD3
flash
S1
[S2 + S3]
LD1 + LD2 + LD3
flash
S2
Led(s)
(description on page 22 / chapter 6.15)
Level ...... .. .....
LD1
N° of flashes of LED End of cycle ... 1 ... ... ... ...
flashes 10
ex. level 3: 3 flashes, pause .... repeated for 1 minute
LD2
(description on page 20 / chapter 6.11)
Press key S2 and press again: the end of cycle LED lights then switches off.
(LED lit = function activated)
flashes
(description on page 27 / chapter 10)
LD1
The end of cycle LED emits a series of flashes which correspond to the type
of alarm
flashes
The last 3 alarms can be displayed by pressing
LD2
When pressed from the 4
actioned (description on page 27 / chapter 10)
flashes
All LEDs
(description on page 28 / chapter 10.3)
flash
All the LEDs flash for 30 seconds.
(description on page 28 / chapter 10.4)
LD3
The cycle starts automatically signalling the various current phases with the
flashes
lightning of the corresponding LEDs.
LD1
(description on page 29 / chapter 10.5.1)
flashes
Press key S1 and press again: the end of cycle LED lights then switches off
LD11
(Led on = active function)
On/Off
LD2
description on page 29 / chapter 10.5.2)
flashes
Press key S2 and press again: the end of cycle LED lights then switches off
LD11
(Led on = pulse; Led off = continuous)
On/Off
35 /35
Brief description / Comments
..... ..... ... L1 ... ... ... ... L2 ... ... ... ... ... ... L10
2 ... ... ... ... ... ...
S1
th th
to the 10 time, the individual components are
599 35 90-23