Quick Guide To The Special Functions - Electrolux EDW 1500 - 1510 Service Manual

12 QUICK GUIDE TO THE SPECIAL FUNCTIONS

The table below briefly describes how each of the special functions available to the user and to the Service Engineer can be used.
Function Activation of the function
Buttons
S0
(On/Off)
Select regeneration
[S2 + S3]
S0
(On/Off)
Disactivate
rinse-aid
[S2 + S3]
S0
(On/Off)
Disactivate buzzer
[S2 + S3]
[S1 + S3]
Display of alarms
and components
diagnostics
S0
(On/Off)
[S1 + S3]
Cancel alarms
stored in memory
S0
(On/Off)
[S1 + S3]
Test cycle
S0
(On/Off)
[S1 + S3]
Extra rinse
S0
(On/Off)
[S1 + S3]
Disable buttons
S0
(On/Off)
In order to memorize the functions or exit diagnostics mode, press key S0 to switch the appliance off
Exit / Memorize
automatically after 60 seconds (in which case the appliance returns to pre-selection mode).
(*) To activate the functions available to the user, no cycles must be selected (i.e. the appliance must be in pre-selection mode).
SOI/TD - PR
Starting the function
Led(s) Buttons
LD1 + LD2+ LD3
S1
flashing
LD1 flashes
LD1 + LD2+ LD3
S2
flashing
LD2 flashes
LD1 + LD2+ LD3
S3
flashing
LD3 flashes
LD1 + LD2 + LD3
S1
flashing
LD1 flashes
LD1 + LD2 + LD3
S2
flashing
LD1 + LD2 + LD3
S3
flashing
LD3 flashes
[S1 + S2]
LD1 + LD2 + LD3
flashing
S1
LD1 flashes
[S2 + S3]
LD1 + LD2 + LD3
flashing
S2
LD2 flashes
Display
(description on page 24 / chapter 6.14). Press S1:
Liv....[1L]......[2L]....[3L]......[ 4L]......[ 5L].... [ 6L ]......[ 7L] ....[ 8L]......[ 9L].......[10L]
1L ..... 10L
° F... >8 ..... >14 .....>20 ..... >30 ..... >40 ..... >50 ..... >60 ..... >70 ..... >80 ....... >90
° D... >4 ...... >8 ...... >11 ..... >17 ..... >22 ..... >28 ..... >33 ..... >39 ..... >45 ....... >50
(description on page 22 / chapter 6.10)
0d / 1d
Press S2 and press again: 1d = rinse-aid activated, 0d = not activated
(description on page 11 / chapter 4.6.1)
0b / 1b
Press S3 and press again: 1b = buzzer activated, 0b = not activated
(description on page 29 / chapter 10.2).
i_0 / 4......10
Press button
[i.0] [i.0]
flashing
AL 1 AL2
(description on page 30 / chapter 10.3)
[ 188 ]
All the LEDs and digits flash for 30 sec.
[ 50 ]
(description on page 30 / chapter 10.4)
Time-to-end
The cycle starts automatically
(description on page 31 / chapter 10.5.1)
0A / 1A
Press S1 and press again: 1A = rinse activated 0A = not activated
flashing
(description on page 31 / chapter 10.5.2)
0P / 1P
Press S2 and press again: 1P = pulse wash PW activated;
flashing
0P = continuous wash
(
On/Off). In most cases, memorization / exit take place
37
Brief description / Comments
S1:
[i.0] [4 ] [ 5] [ 6] [ 7 ] [ 8] [ 9 ]
PS
AL 3 ER EV RR PL DD
[10]
MV
599 36 01-86