Quick Guide To The Special Functions - Electrolux DIVA 60 cm Service Manual

12 QUICK GUIDE TO THE SPECIAL FUNCTIONS

The table below briefly describes how each of the special functions available
to the user and to the Service Engineer can be used.
Function Activation of the function
Keys
[S1 + S2]
Select regeneration
S0 (On/Off)
S0 (On/Off)
Disactivate rinse-
aid
[S2 + S3]
S0 (On/Off)
Disactivate buzzer
[S2 + S3]
Display of alarms [S1 + S3]
and components
S0 (On/Off)
diagnostics
[S1 + S3]
Cancel alarms
stored in memory
S0 (On/Off)
[S1 + S3]
Test cycle
S0 (On/Off)
[S1 + S3]
Extra rinse
S0 (On/Off)
[S1 + S3]
Disable buttons
S0 (On/Off)
In order to memorize the functions or exit diagnostics mode, press key S0 to switch the appliance off. In most cases, memorization / exit take place automatically after 60 seconds (in
Exit / Memorize
which case the appliance returns to pre-selection mode)
(*) To activate the functions available to the user, no cycles must be selected (i.e. the appliance must be in pre-selection mode).
SOI/DT 2003 -01 eb
Starting the function
Led(s) Keys
LD1 + LD2
S1
flashing
LD1 + LD2+ LD3
S2
flashing
LD1 + LD2+ LD3
S3
flashing
LD1 + LD2 + LD3
S1
flashing
LD1 + LD2 + LD3
S2
flashing
LD1 + LD2 + LD3
S3
flashing
[S1 + S2]
LD1 + LD2 + LD3
flashing
S1
[S2 + S3]
LD1 + LD2 + LD3
flashing
S2
Led(s)
(description on page 23 – section 6.15)
LD1
Level
flashing
N° of flashes
Example: level 3: [3 flashes, 5 sec pause] repeated for 1 minute
(description on page 21 – section 6.11)
LD2
Press key S2 and press again: the end of cycle LED lights then switches off.
flashing
(LED lit = function activated)
(description on page 10 – section 4.6.1)
LD3
Press key S3 and press again: the end of cycle LED lights then switches off
flashing
(LED lit = function activated)
(description on page 28 – section 10.2)
The end of cycle LED emits a series of flashes which correspond to the type
LD1 of alarm (see section 9.1)
flashing The last 3 alarms can be displayed by pressing
When pressed from the 4
actioned.
LD2
(description on page 29 – section 10.3)
flashing
All the LEDs flash for 30 seconds.
LD3
(description on page 29 – section 10.4)
flashing
The cycle starts automatically.
LD1 (description on page 29 – section 10.5.1)
flashing Press key S2 and press again: the end of cycle LED lights then switches off
(LED lit = function activated)
(description on page 29 – section 10.5.2)
LD2
Press key S2 and press again: the end of cycle LED lights then switches off
flashing
(LED lit = function activated)
37
Brief description / Comments
L1 L2 and in sequence up to ......L10
1 2
S1
th th
to the 10 time, the individual components are
10
599 35 64-85