Before Using Your Range - Kenmore 970-3395 Use & Care Manual

Before Using Your Range

Assembly of Burner Heads & Burner Caps (for Deep Well Cooktop models only)
Your range is shipped with the Burner Heads and Burner Caps in the correct locations. Packing material is located between
the Burner Heads and the cooktop.
a. Be sure to follow the installation instructions before
installing and using your new range.
b. Remove all packing tape from cooktop area. Remove all
Burner Caps and Burner Heads.
c. Discard all packing material located under Burner Heads.
d. To replace Burner Heads & Caps, match the letters
located under center of Burner Caps with the letters
located inside Burner Heads (Fig. 1).
e. Match the letters stamped on Burner Skirts with Burner
Heads and Burner Caps (See Fig. 1). Replace the Burner
Heads and Caps on cooktop (See Fig. 2). Carefully align
the Electrodes into slot or hole of each Burner Head (Fig.
3). Note: The Burner Heads should sit flat on Cooktop
Burner Skirts.
f. Unpack Burner Grates and position on the cooktop.
Assembly of Burner Heads & Burner Caps (for Ceramic Glass Cooktop models only)
Your range is shipped with the Burner Heads and Burner Caps in the correct locations. Packing material is located between
the Burner Heads and burner skirts.
a. Be sure to follow the installation instructions before
installing and using your new range.
b. Remove any packing tape from cooktop. Remove all
Burner Caps and Burner Heads, except DO NOT RE-
MOVE Burner Head for Triple Ring Burner (right-front
burner position; See Fig. 4).
c. Discard any packing material located under the Burner
Heads (except Triple Ring Burner position).
d. Replace right rear Burner Head & Cap onto cooktop.
Match the letter for the right-rear burner located inside of
Burner Cap with the letter located inside Burner Head
(only the right-rear position is marked with letter A - See
Fig. 5). Carefully align the Electrode into slot of Simmer
Burner Head (Fig. 7).
e. CAREFULLY (DO NOT FORCE) align the Bridge Burner
Head over the 2 Bridge Burner Electrodes located on left
side of the cooktop. After placing the Bridge Burner Head
on the burner skirt, MAKE SURE that the Bridge Burner
Head lies evenly on burner skirt.
f. Replace Bridge Burner Caps. These include 1 Bridge
Burner Center Cap (rectangular shaped) and the 2 Bridge
Burner End Caps (The Bridge Burner End Caps will fit at
either the front or rear Bridge Burner Head locations).
Make sure that the tabs located under the Bridge Burner
Caps fall into the slots located in the Bridge Burner Head
(See black arrows in Fig. 6) and that the Bridge Burner
Caps lie flat and evenly on top the Bridge Burner Head.
g. Unpack Burner Grates. Position End Burner Grates on
cooktop. Place Center Burner Grate between the end
Burner Grates and check that all the Burner Grate legs lie
flat on the glass cooktop surface.
B
Burner
Cap
B
Burner
Head
Electrode
Burner Skirt
Fig. 1
Fig. 1
Fig. 1
Fig. 4
Bridge Burner
Head
Bridge
Bridge
Burner
Burner
End
End
Cap
Cap
Bridge
Bridge
Burner
Burner
Center
Center
Cap
Cap
Bridge
Bridge
Burner
Burner
End
End
Cap
Cap
Fig. 6
7
A A
E
4.2k k k
B
1 1 7.2 1
9.5k
Fig. 2
Electrodes must
align into slot or hole for each
Fig. 3
Burner Head
Fig. 5
2 Electrode
Electrode
must align into slot or hole
hole
for Simmer Burner Head
locations
through
Fig. 7
Bridge
Burner
Head
k